From: Jagan Teki <jteki@openedev.com>
To: u-boot@lists.denx.de
Subject: [U-Boot] [U-Boot PATCH v2 02/17] spi: Zap ftssp010_spi driver
Date: Sun, 10 May 2015 20:45:42 +0530 [thread overview]
Message-ID: <1431270957-6901-3-git-send-email-jteki@openedev.com> (raw)
In-Reply-To: <1431270957-6901-1-git-send-email-jteki@openedev.com>
Zap ftssp010_spi driver since the boards used this driver
is no longer been active.
Signed-off-by: Jagan Teki <jteki@openedev.com>
Cc: Kuo-Jung Su <dantesu@faraday-tech.com>
Cc: Axel Lin <axel.lin@ingics.com>
---
drivers/spi/Makefile | 1 -
drivers/spi/ftssp010_spi.c | 498 ---------------------------------------------
2 files changed, 499 deletions(-)
delete mode 100644 drivers/spi/ftssp010_spi.c
diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile
index 93065b7..1e3611d 100644
--- a/drivers/spi/Makefile
+++ b/drivers/spi/Makefile
@@ -28,7 +28,6 @@ obj-$(CONFIG_CF_QSPI) += cf_qspi.o
obj-$(CONFIG_DAVINCI_SPI) += davinci_spi.o
obj-$(CONFIG_DESIGNWARE_SPI) += designware_spi.o
obj-$(CONFIG_EXYNOS_SPI) += exynos_spi.o
-obj-$(CONFIG_FTSSP010_SPI) += ftssp010_spi.o
obj-$(CONFIG_ICH_SPI) += ich.o
obj-$(CONFIG_KIRKWOOD_SPI) += kirkwood_spi.o
obj-$(CONFIG_LPC32XX_SSP) += lpc32xx_ssp.o
diff --git a/drivers/spi/ftssp010_spi.c b/drivers/spi/ftssp010_spi.c
deleted file mode 100644
index c7d6480..0000000
--- a/drivers/spi/ftssp010_spi.c
+++ /dev/null
@@ -1,498 +0,0 @@
-/*
- * (C) Copyright 2013
- * Faraday Technology Corporation. <http://www.faraday-tech.com/tw/>
- * Kuo-Jung Su <dantesu@gmail.com>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <linux/compat.h>
-#include <asm/io.h>
-#include <malloc.h>
-#include <spi.h>
-
-#ifndef CONFIG_FTSSP010_BASE_LIST
-#define CONFIG_FTSSP010_BASE_LIST { CONFIG_FTSSP010_BASE }
-#endif
-
-#ifndef CONFIG_FTSSP010_GPIO_BASE
-#define CONFIG_FTSSP010_GPIO_BASE 0
-#endif
-
-#ifndef CONFIG_FTSSP010_GPIO_LIST
-#define CONFIG_FTSSP010_GPIO_LIST { CONFIG_FTSSP010_GPIO_BASE }
-#endif
-
-#ifndef CONFIG_FTSSP010_CLOCK
-#define CONFIG_FTSSP010_CLOCK clk_get_rate("SSP");
-#endif
-
-#ifndef CONFIG_FTSSP010_TIMEOUT
-#define CONFIG_FTSSP010_TIMEOUT 100
-#endif
-
-/* FTSSP010 chip registers */
-struct ftssp010_regs {
- uint32_t cr[3];/* control register */
- uint32_t sr; /* status register */
- uint32_t icr; /* interrupt control register */
- uint32_t isr; /* interrupt status register */
- uint32_t dr; /* data register */
- uint32_t rsvd[17];
- uint32_t revr; /* revision register */
- uint32_t fear; /* feature register */
-};
-
-/* Control Register 0 */
-#define CR0_FFMT_MASK (7 << 12)
-#define CR0_FFMT_SSP (0 << 12)
-#define CR0_FFMT_SPI (1 << 12)
-#define CR0_FFMT_MICROWIRE (2 << 12)
-#define CR0_FFMT_I2S (3 << 12)
-#define CR0_FFMT_AC97 (4 << 12)
-#define CR0_FLASH (1 << 11)
-#define CR0_FSDIST(x) (((x) & 0x03) << 8)
-#define CR0_LOOP (1 << 7) /* loopback mode */
-#define CR0_LSB (1 << 6) /* LSB */
-#define CR0_FSPO (1 << 5) /* fs atcive low (I2S only) */
-#define CR0_FSJUSTIFY (1 << 4)
-#define CR0_OPM_SLAVE (0 << 2)
-#define CR0_OPM_MASTER (3 << 2)
-#define CR0_OPM_I2S_MSST (3 << 2) /* master stereo mode */
-#define CR0_OPM_I2S_MSMO (2 << 2) /* master mono mode */
-#define CR0_OPM_I2S_SLST (1 << 2) /* slave stereo mode */
-#define CR0_OPM_I2S_SLMO (0 << 2) /* slave mono mode */
-#define CR0_SCLKPO (1 << 1) /* clock polarity */
-#define CR0_SCLKPH (1 << 0) /* clock phase */
-
-/* Control Register 1 */
-#define CR1_PDL(x) (((x) & 0xff) << 24) /* padding length */
-#define CR1_SDL(x) ((((x) - 1) & 0x1f) << 16) /* data length */
-#define CR1_DIV(x) (((x) - 1) & 0xffff) /* clock divider */
-
-/* Control Register 2 */
-#define CR2_CS(x) (((x) & 3) << 10) /* CS/FS select */
-#define CR2_FS (1 << 9) /* CS/FS signal level */
-#define CR2_TXEN (1 << 8) /* tx enable */
-#define CR2_RXEN (1 << 7) /* rx enable */
-#define CR2_RESET (1 << 6) /* chip reset */
-#define CR2_TXFC (1 << 3) /* tx fifo Clear */
-#define CR2_RXFC (1 << 2) /* rx fifo Clear */
-#define CR2_TXDOE (1 << 1) /* tx data output enable */
-#define CR2_EN (1 << 0) /* chip enable */
-
-/* Status Register */
-#define SR_RFF (1 << 0) /* rx fifo full */
-#define SR_TFNF (1 << 1) /* tx fifo not full */
-#define SR_BUSY (1 << 2) /* chip busy */
-#define SR_RFVE(reg) (((reg) >> 4) & 0x1f) /* rx fifo valid entries */
-#define SR_TFVE(reg) (((reg) >> 12) & 0x1f) /* tx fifo valid entries */
-
-/* Feature Register */
-#define FEAR_BITS(reg) ((((reg) >> 0) & 0xff) + 1) /* data width */
-#define FEAR_RFSZ(reg) ((((reg) >> 8) & 0xff) + 1) /* rx fifo size */
-#define FEAR_TFSZ(reg) ((((reg) >> 16) & 0xff) + 1) /* tx fifo size */
-#define FEAR_AC97 (1 << 24)
-#define FEAR_I2S (1 << 25)
-#define FEAR_SPI_MWR (1 << 26)
-#define FEAR_SSP (1 << 27)
-#define FEAR_SPDIF (1 << 28)
-
-/* FTGPIO010 chip registers */
-struct ftgpio010_regs {
- uint32_t out; /* 0x00: Data Output */
- uint32_t in; /* 0x04: Data Input */
- uint32_t dir; /* 0x08: Direction */
- uint32_t bypass; /* 0x0c: Bypass */
- uint32_t set; /* 0x10: Data Set */
- uint32_t clr; /* 0x14: Data Clear */
- uint32_t pull_up; /* 0x18: Pull-Up Enabled */
- uint32_t pull_st; /* 0x1c: Pull State (0=pull-down, 1=pull-up) */
-};
-
-struct ftssp010_gpio {
- struct ftgpio010_regs *regs;
- uint32_t pin;
-};
-
-struct ftssp010_spi {
- struct spi_slave slave;
- struct ftssp010_gpio gpio;
- struct ftssp010_regs *regs;
- uint32_t fifo;
- uint32_t mode;
- uint32_t div;
- uint32_t clk;
- uint32_t speed;
- uint32_t revision;
-};
-
-static inline struct ftssp010_spi *to_ftssp010_spi(struct spi_slave *slave)
-{
- return container_of(slave, struct ftssp010_spi, slave);
-}
-
-static int get_spi_chip(int bus, struct ftssp010_spi *chip)
-{
- uint32_t fear, base[] = CONFIG_FTSSP010_BASE_LIST;
-
- if (bus >= ARRAY_SIZE(base) || !base[bus])
- return -1;
-
- chip->regs = (struct ftssp010_regs *)base[bus];
-
- chip->revision = readl(&chip->regs->revr);
-
- fear = readl(&chip->regs->fear);
- chip->fifo = min_t(uint32_t, FEAR_TFSZ(fear), FEAR_RFSZ(fear));
-
- return 0;
-}
-
-static int get_spi_gpio(int bus, struct ftssp010_gpio *chip)
-{
- uint32_t base[] = CONFIG_FTSSP010_GPIO_LIST;
-
- if (bus >= ARRAY_SIZE(base) || !base[bus])
- return -1;
-
- chip->regs = (struct ftgpio010_regs *)(base[bus] & 0xfff00000);
- chip->pin = base[bus] & 0x1f;
-
- /* make it an output pin */
- setbits_le32(&chip->regs->dir, 1 << chip->pin);
-
- return 0;
-}
-
-static int ftssp010_wait(struct ftssp010_spi *chip)
-{
- struct ftssp010_regs *regs = chip->regs;
- ulong t;
-
- /* wait until device idle */
- for (t = get_timer(0); get_timer(t) < CONFIG_FTSSP010_TIMEOUT; ) {
- if (!(readl(®s->sr) & SR_BUSY))
- return 0;
- }
-
- puts("ftspi010: busy timeout\n");
-
- return -1;
-}
-
-static int ftssp010_wait_tx(struct ftssp010_spi *chip)
-{
- struct ftssp010_regs *regs = chip->regs;
- ulong t;
-
- /* wait until tx fifo not full */
- for (t = get_timer(0); get_timer(t) < CONFIG_FTSSP010_TIMEOUT; ) {
- if (readl(®s->sr) & SR_TFNF)
- return 0;
- }
-
- puts("ftssp010: tx timeout\n");
-
- return -1;
-}
-
-static int ftssp010_wait_rx(struct ftssp010_spi *chip)
-{
- struct ftssp010_regs *regs = chip->regs;
- ulong t;
-
- /* wait until rx fifo not empty */
- for (t = get_timer(0); get_timer(t) < CONFIG_FTSSP010_TIMEOUT; ) {
- if (SR_RFVE(readl(®s->sr)))
- return 0;
- }
-
- puts("ftssp010: rx timeout\n");
-
- return -1;
-}
-
-static int ftssp010_spi_work_transfer_v2(struct ftssp010_spi *chip,
- const void *tx_buf, void *rx_buf, int len, uint flags)
-{
- struct ftssp010_regs *regs = chip->regs;
- const uint8_t *txb = tx_buf;
- uint8_t *rxb = rx_buf;
-
- while (len > 0) {
- int i, depth = min(chip->fifo >> 2, len);
- uint32_t xmsk = 0;
-
- if (tx_buf) {
- for (i = 0; i < depth; ++i) {
- ftssp010_wait_tx(chip);
- writel(*txb++, ®s->dr);
- }
- xmsk |= CR2_TXEN | CR2_TXDOE;
- if ((readl(®s->cr[2]) & xmsk) != xmsk)
- setbits_le32(®s->cr[2], xmsk);
- }
- if (rx_buf) {
- xmsk |= CR2_RXEN;
- if ((readl(®s->cr[2]) & xmsk) != xmsk)
- setbits_le32(®s->cr[2], xmsk);
- for (i = 0; i < depth; ++i) {
- ftssp010_wait_rx(chip);
- *rxb++ = (uint8_t)readl(®s->dr);
- }
- }
-
- len -= depth;
- }
-
- return 0;
-}
-
-static int ftssp010_spi_work_transfer_v1(struct ftssp010_spi *chip,
- const void *tx_buf, void *rx_buf, int len, uint flags)
-{
- struct ftssp010_regs *regs = chip->regs;
- const uint8_t *txb = tx_buf;
- uint8_t *rxb = rx_buf;
-
- while (len > 0) {
- int i, depth = min(chip->fifo >> 2, len);
- uint32_t tmp;
-
- for (i = 0; i < depth; ++i) {
- ftssp010_wait_tx(chip);
- writel(txb ? (*txb++) : 0, ®s->dr);
- }
- for (i = 0; i < depth; ++i) {
- ftssp010_wait_rx(chip);
- tmp = readl(®s->dr);
- if (rxb)
- *rxb++ = (uint8_t)tmp;
- }
-
- len -= depth;
- }
-
- return 0;
-}
-
-static void ftssp010_cs_set(struct ftssp010_spi *chip, int high)
-{
- struct ftssp010_regs *regs = chip->regs;
- struct ftssp010_gpio *gpio = &chip->gpio;
- uint32_t mask;
-
- /* cs pull high/low */
- if (chip->revision >= 0x11900) {
- mask = CR2_CS(chip->slave.cs) | (high ? CR2_FS : 0);
- writel(mask, ®s->cr[2]);
- } else if (gpio->regs) {
- mask = 1 << gpio->pin;
- if (high)
- writel(mask, &gpio->regs->set);
- else
- writel(mask, &gpio->regs->clr);
- }
-
- /* extra delay for signal propagation */
- udelay_masked(1);
-}
-
-/*
- * Determine if a SPI chipselect is valid.
- * This function is provided by the board if the low-level SPI driver
- * needs it to determine if a given chipselect is actually valid.
- *
- * Returns: 1 if bus:cs identifies a valid chip on this board, 0
- * otherwise.
- */
-int spi_cs_is_valid(unsigned int bus, unsigned int cs)
-{
- struct ftssp010_spi chip;
-
- if (get_spi_chip(bus, &chip))
- return 0;
-
- if (!cs)
- return 1;
- else if ((cs < 4) && (chip.revision >= 0x11900))
- return 1;
-
- return 0;
-}
-
-/*
- * Activate a SPI chipselect.
- * This function is provided by the board code when using a driver
- * that can't control its chipselects automatically (e.g.
- * common/soft_spi.c). When called, it should activate the chip select
- * to the device identified by "slave".
- */
-void spi_cs_activate(struct spi_slave *slave)
-{
- struct ftssp010_spi *chip = to_ftssp010_spi(slave);
- struct ftssp010_regs *regs = chip->regs;
-
- /* cs pull */
- if (chip->mode & SPI_CS_HIGH)
- ftssp010_cs_set(chip, 1);
- else
- ftssp010_cs_set(chip, 0);
-
- /* chip enable + fifo clear */
- setbits_le32(®s->cr[2], CR2_EN | CR2_TXFC | CR2_RXFC);
-}
-
-/*
- * Deactivate a SPI chipselect.
- * This function is provided by the board code when using a driver
- * that can't control its chipselects automatically (e.g.
- * common/soft_spi.c). When called, it should deactivate the chip
- * select to the device identified by "slave".
- */
-void spi_cs_deactivate(struct spi_slave *slave)
-{
- struct ftssp010_spi *chip = to_ftssp010_spi(slave);
-
- /* wait until chip idle */
- ftssp010_wait(chip);
-
- /* cs pull */
- if (chip->mode & SPI_CS_HIGH)
- ftssp010_cs_set(chip, 0);
- else
- ftssp010_cs_set(chip, 1);
-}
-
-void spi_init(void)
-{
- /* nothing to do */
-}
-
-struct spi_slave *spi_setup_slave(uint bus, uint cs, uint max_hz, uint mode)
-{
- struct ftssp010_spi *chip;
-
- if (mode & SPI_3WIRE) {
- puts("ftssp010: can't do 3-wire\n");
- return NULL;
- }
-
- if (mode & SPI_SLAVE) {
- puts("ftssp010: can't do slave mode\n");
- return NULL;
- }
-
- if (mode & SPI_PREAMBLE) {
- puts("ftssp010: can't skip preamble bytes\n");
- return NULL;
- }
-
- if (!spi_cs_is_valid(bus, cs)) {
- puts("ftssp010: invalid (bus, cs)\n");
- return NULL;
- }
-
- chip = spi_alloc_slave(struct ftssp010_spi, bus, cs);
- if (!chip)
- return NULL;
-
- if (get_spi_chip(bus, chip))
- goto free_out;
-
- if (chip->revision < 0x11900 && get_spi_gpio(bus, &chip->gpio)) {
- puts("ftssp010: Before revision 1.19.0, its clock & cs are\n"
- "controlled by tx engine which is not synced with rx engine,\n"
- "so the clock & cs might be shutdown before rx engine\n"
- "finishs its jobs.\n"
- "If possible, please add a dedicated gpio for it.\n");
- }
-
- chip->mode = mode;
- chip->clk = CONFIG_FTSSP010_CLOCK;
- chip->div = 2;
- if (max_hz) {
- while (chip->div < 0xffff) {
- if ((chip->clk / (2 * chip->div)) <= max_hz)
- break;
- chip->div += 1;
- }
- }
- chip->speed = chip->clk / (2 * chip->div);
-
- return &chip->slave;
-
-free_out:
- free(chip);
- return NULL;
-}
-
-void spi_free_slave(struct spi_slave *slave)
-{
- struct ftssp010_spi *chip = to_ftssp010_spi(slave);
-
- free(chip);
-}
-
-int spi_claim_bus(struct spi_slave *slave)
-{
- struct ftssp010_spi *chip = to_ftssp010_spi(slave);
- struct ftssp010_regs *regs = chip->regs;
-
- writel(CR1_SDL(8) | CR1_DIV(chip->div), ®s->cr[1]);
-
- if (chip->revision >= 0x11900) {
- writel(CR0_OPM_MASTER | CR0_FFMT_SPI | CR0_FSPO | CR0_FLASH,
- ®s->cr[0]);
- writel(CR2_TXFC | CR2_RXFC,
- ®s->cr[2]);
- } else {
- writel(CR0_OPM_MASTER | CR0_FFMT_SPI | CR0_FSPO,
- ®s->cr[0]);
- writel(CR2_TXFC | CR2_RXFC | CR2_EN | CR2_TXDOE,
- ®s->cr[2]);
- }
-
- if (chip->mode & SPI_LOOP)
- setbits_le32(®s->cr[0], CR0_LOOP);
-
- if (chip->mode & SPI_CPOL)
- setbits_le32(®s->cr[0], CR0_SCLKPO);
-
- if (chip->mode & SPI_CPHA)
- setbits_le32(®s->cr[0], CR0_SCLKPH);
-
- spi_cs_deactivate(slave);
-
- return 0;
-}
-
-void spi_release_bus(struct spi_slave *slave)
-{
- struct ftssp010_spi *chip = to_ftssp010_spi(slave);
- struct ftssp010_regs *regs = chip->regs;
-
- writel(0, ®s->cr[2]);
-}
-
-int spi_xfer(struct spi_slave *slave, unsigned int bitlen,
- const void *dout, void *din, unsigned long flags)
-{
- struct ftssp010_spi *chip = to_ftssp010_spi(slave);
- uint32_t len = bitlen >> 3;
-
- if (flags & SPI_XFER_BEGIN)
- spi_cs_activate(slave);
-
- if (chip->revision >= 0x11900)
- ftssp010_spi_work_transfer_v2(chip, dout, din, len, flags);
- else
- ftssp010_spi_work_transfer_v1(chip, dout, din, len, flags);
-
- if (flags & SPI_XFER_END)
- spi_cs_deactivate(slave);
-
- return 0;
-}
--
1.9.1
next prev parent reply other threads:[~2015-05-10 15:15 UTC|newest]
Thread overview: 21+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-05-10 15:15 [U-Boot] [U-Boot PATCH v2 00/17] spi/sf: Cleansup and driver model conversions Jagan Teki
2015-05-10 15:15 ` [U-Boot] [U-Boot PATCH v2 01/17] spi: Zap andes_spi driver Jagan Teki
2015-05-10 15:15 ` Jagan Teki [this message]
2015-05-10 15:15 ` [U-Boot] [U-Boot PATCH v2 03/17] spi: Zap oc_tiny_spi driver Jagan Teki
2015-05-10 15:15 ` [U-Boot] [U-Boot PATCH v2 04/17] spi: xilinx_spi: Move header code to driver Jagan Teki
2015-05-10 15:15 ` [U-Boot] [U-Boot PATCH v2 05/17] spi: xilinx_spi: Driver clean-up Jagan Teki
2015-05-10 15:15 ` [U-Boot] [U-Boot PATCH v2 06/17] spi: davinci_spi: Move header code to driver Jagan Teki
2015-05-10 15:15 ` [U-Boot] [U-Boot PATCH v2 07/17] spi: davinci_spi: Driver cleanup Jagan Teki
2015-05-10 15:15 ` [U-Boot] [U-Boot PATCH v2 08/17] spi/sf: Minor cleanups Jagan Teki
2015-05-10 15:15 ` [U-Boot] [U-Boot PATCH v2 09/17] dm: spi: zynq_spi: Convert to driver model Jagan Teki
2015-05-10 15:15 ` [U-Boot] [U-Boot PATCH v2 10/17] zynq: Kconfig: Enable dm spi and spi_flash Jagan Teki
2015-05-10 15:15 ` [U-Boot] [U-Boot PATCH v2 11/17] dts: zynq: Add zynq spi controller nodes Jagan Teki
2015-05-10 15:15 ` [U-Boot] [U-Boot PATCH v2 12/17] spi: zynq_spi: Add fdt support in driver Jagan Teki
2015-05-10 15:15 ` [U-Boot] [U-Boot PATCH v2 13/17] dts: zynq: Enable spi1 for zc770_xm010 board Jagan Teki
2015-06-16 11:28 ` Jagan Teki
2015-06-16 13:34 ` Michal Simek
2015-05-10 15:15 ` [U-Boot] [U-Boot PATCH v2 14/17] dm: spi: xilinx_spi: Convert to driver model Jagan Teki
2015-05-10 15:15 ` [U-Boot] [U-Boot PATCH v2 15/17] spi: xilinx_spi: Add asm/io.h include file Jagan Teki
2015-05-10 15:15 ` [U-Boot] [U-Boot PATCH v2 16/17] spi: Kconfig: Add Zynq QSPI controller entry Jagan Teki
2015-05-10 15:15 ` [U-Boot] [U-Boot PATCH v2 17/17] spi: Kconfig: Add Zynq SPI " Jagan Teki
2015-05-12 3:57 ` [U-Boot] [U-Boot PATCH v2 00/17] spi/sf: Cleansup and driver model conversions Jagan Teki
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1431270957-6901-3-git-send-email-jteki@openedev.com \
--to=jteki@openedev.com \
--cc=u-boot@lists.denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.