From: Andreas Dannenberg <dannenberg@ti.com>
To: Sebastian Reichel <sre@kernel.org>,
Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>,
David Woodhouse <dwmw2@infradead.org>,
Laurentiu Palcu <laurentiu.palcu@intel.com>,
Krzysztof Kozlowski <k.kozlowski@samsung.com>
Cc: Ramakrishna Pallala <ramakrishna.pallala@intel.com>,
linux-pm@vger.kernel.org, devicetree@vger.kernel.org,
Andreas Dannenberg <dannenberg@ti.com>
Subject: [PATCH v3 01/10] dt: power: bq24257-charger: Cover additional devices
Date: Fri, 11 Sep 2015 15:26:33 -0500 [thread overview]
Message-ID: <1442003202-1430-2-git-send-email-dannenberg@ti.com> (raw)
In-Reply-To: <1442003202-1430-1-git-send-email-dannenberg@ti.com>
Extend the bq24257 charger's device tree documentation to cover the
bq24250 and bq24251 devices as well feature additions.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
---
.../devicetree/bindings/power/bq24257.txt | 59 ++++++++++++++++++++--
1 file changed, 54 insertions(+), 5 deletions(-)
diff --git a/Documentation/devicetree/bindings/power/bq24257.txt b/Documentation/devicetree/bindings/power/bq24257.txt
index 5c9d394..4a88c96 100644
--- a/Documentation/devicetree/bindings/power/bq24257.txt
+++ b/Documentation/devicetree/bindings/power/bq24257.txt
@@ -1,21 +1,70 @@
-Binding for TI bq24257 Li-Ion Charger
+Binding for TI bq24250/bq24251/bq24257 Li-Ion Charger
Required properties:
- compatible: Should contain one of the following:
+ * "ti,bq24250"
+ * "ti,bq24251"
* "ti,bq24257"
-- reg: integer, i2c address of the device.
+- reg: integer, i2c address of the device.
+- stat-gpios: GPIO used for the devices STAT_IN pin. Alternatively the pin can
+ also be defined through the standard interrupt definition properties (see
+ optional properties section below). Only use one method.
- ti,battery-regulation-voltage: integer, maximum charging voltage in uV.
-- ti,charge-current: integer, maximum charging current in uA.
-- ti,termination-current: integer, charge will be terminated when current in
- constant-voltage phase drops below this value (in uA).
+- ti,charge-current: integer, maximum charging current in uA.
+- ti,termination-current: integer, charge will be terminated when current in
+ constant-voltage phase drops below this value (in uA).
+
+Optional properties:
+- pg-gpios: GPIO used for connecting the bq2425x device PG (Power Good) pin.
+ This pin is not available on all devices however it should be used if
+ possible as this is the recommended way to obtain the charger's input PG
+ state. If this pin is not specified a software-based approach for PG
+ detection is used.
+- ti,current-limit: The maximum current to be drawn from the charger's input
+ (in uA). If this property is not specified a USB D+/D- signal based charger
+ type detection is used (if available) and the input limit current is set
+ accordingly. If the D+/D- based detection is not available on a given device
+ a default of 500,000 is used (=500mA).
+- ti,ovp-voltage: Configures the over voltage protection voltage (in uV). If
+ not specified a default of 6,5000,000 (=6.5V) is used.
+- ti,in-dpm-voltage: Configures the threshold input voltage for the dynamic
+ power path management (in uV). If not specified a default of 4,360,000
+ (=4.36V) is used.
+- ti,safety-timer-2x-enable: If this property is set to 1 the device's safety
+ timer is extended (slowed down) by a factor of two. Setting this property
+ to 0 or not providing it will leave the safety timer at its default
+ setting.
+- interrupt-parent: Should be the phandle for the interrupt controller. Use in
+ conjunction with "interrupts" and only in case "stat-gpios" is not used.
+- interrupts: Interrupt mapping for GPIO IRQ (configure for both edges). Use in
+ conjunction with "interrupt-parent" and only in case "stat-gpios" is not
+ used.
Example:
bq24257 {
compatible = "ti,bq24257";
reg = <0x6a>;
+ stat-gpios = <&gpio1 16 GPIO_ACTIVE_HIGH>;
+ pg-gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>;
ti,battery-regulation-voltage = <4200000>;
ti,charge-current = <1000000>;
ti,termination-current = <50000>;
};
+
+Example:
+
+bq24250 {
+ compatible = "ti,bq24250";
+ reg = <0x6a>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <16 IRQ_TYPE_EDGE_BOTH>;
+
+ ti,battery-regulation-voltage = <4200000>;
+ ti,charge-current = <500000>;
+ ti,termination-current = <50000>;
+ ti,current-limit = <900000>;
+ ti,ovp-voltage = <9500000>;
+ ti,in-dpm-voltage = <4440000>;
+};
--
1.9.1
next prev parent reply other threads:[~2015-09-11 20:26 UTC|newest]
Thread overview: 17+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-09-11 20:26 [PATCH v3 00/10] power: bq24257: Add support for bq24250/bq24251 Andreas Dannenberg
2015-09-11 20:26 ` Andreas Dannenberg [this message]
2015-09-14 6:11 ` [PATCH v3 01/10] dt: power: bq24257-charger: Cover additional devices Krzysztof Kozlowski
2015-09-14 13:54 ` Andreas Dannenberg
2015-09-15 7:56 ` Krzysztof Kozlowski
2015-09-15 9:05 ` Laurentiu Palcu
2015-09-15 12:51 ` Krzysztof Kozlowski
2015-09-15 13:57 ` Andreas Dannenberg
2015-09-11 20:26 ` [PATCH v3 03/10] power: bq24257: Add bit definition for temp sense enable Andreas Dannenberg
2015-09-11 20:26 ` [PATCH v3 04/10] power: bq24257: Allow manual setting of input current limit Andreas Dannenberg
2015-09-11 20:26 ` [PATCH v3 05/10] power: bq24257: Add SW-based approach for Power Good determination Andreas Dannenberg
[not found] ` <1442003202-1430-1-git-send-email-dannenberg-l0cyMroinI0@public.gmane.org>
2015-09-11 20:26 ` [PATCH v3 02/10] power: bq24257: Add basic support for bq24250/bq24251 Andreas Dannenberg
2015-09-11 20:26 ` [PATCH v3 06/10] power: bq24257: Add over voltage protection setting support Andreas Dannenberg
2015-09-11 20:26 ` [PATCH v3 07/10] power: bq24257: Add input DPM voltage threshold " Andreas Dannenberg
2015-09-11 20:26 ` [PATCH v3 08/10] power: bq24257: Allow input current limit sysfs access Andreas Dannenberg
2015-09-11 20:26 ` [PATCH v3 09/10] power: bq24257: Add various device-specific sysfs properties Andreas Dannenberg
2015-09-11 20:26 ` [PATCH v3 10/10] power: bq24257: Add platform data based initialization Andreas Dannenberg
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1442003202-1430-2-git-send-email-dannenberg@ti.com \
--to=dannenberg@ti.com \
--cc=dbaryshkov@gmail.com \
--cc=devicetree@vger.kernel.org \
--cc=dwmw2@infradead.org \
--cc=k.kozlowski@samsung.com \
--cc=laurentiu.palcu@intel.com \
--cc=linux-pm@vger.kernel.org \
--cc=ramakrishna.pallala@intel.com \
--cc=sre@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.