From: Mike Marciniszyn <mike.marciniszyn-ral2JQCrhuEAvxtiuMwx3w@public.gmane.org>
To: dledford-H+wXaHxf7aLQT0dZR+AlfA@public.gmane.org
Cc: linux-rdma-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
Subject: [PATCH v2 03/49] IB/hfi1: add chip specific support part2
Date: Mon, 15 Jun 2015 09:26:14 -0400 [thread overview]
Message-ID: <20150615132614.29741.21279.stgit@phlsvslse11.ph.intel.com> (raw)
In-Reply-To: <20150615132434.29741.35258.stgit-K+u1se/DcYrLESAwzcoQNrvm/XP+8Wra@public.gmane.org>
Signed-off-by: Andrew Friedley <andrew.friedley-ral2JQCrhuEAvxtiuMwx3w@public.gmane.org>
Signed-off-by: Arthur Kepner <arthur.kepner-ral2JQCrhuEAvxtiuMwx3w@public.gmane.org>
Signed-off-by: Brendan Cunningham <brendan.cunningham-ral2JQCrhuEAvxtiuMwx3w@public.gmane.org>
Signed-off-by: Brian Welty <brian.welty-ral2JQCrhuEAvxtiuMwx3w@public.gmane.org>
Signed-off-by: Caz Yokoyama <caz.yokoyama-ral2JQCrhuEAvxtiuMwx3w@public.gmane.org>
Signed-off-by: Dean Luick <dean.luick-ral2JQCrhuEAvxtiuMwx3w@public.gmane.org>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro-ral2JQCrhuEAvxtiuMwx3w@public.gmane.org>
Signed-off-by: Easwar Hariharan <easwar.hariharan-ral2JQCrhuEAvxtiuMwx3w@public.gmane.org>
Signed-off-by: Harish Chegondi <harish.chegondi-ral2JQCrhuEAvxtiuMwx3w@public.gmane.org>
Signed-off-by: Ira Weiny <ira.weiny-ral2JQCrhuEAvxtiuMwx3w@public.gmane.org>
Signed-off-by: Jim Snow <jim.m.snow-ral2JQCrhuEAvxtiuMwx3w@public.gmane.org>
Signed-off-by: John Gregor <john.a.gregor-ral2JQCrhuEAvxtiuMwx3w@public.gmane.org>
Signed-off-by: Jubin John <jubin.john-ral2JQCrhuEAvxtiuMwx3w@public.gmane.org>
Signed-off-by: Kaike Wan <kaike.wan-ral2JQCrhuEAvxtiuMwx3w@public.gmane.org>
Signed-off-by: Kevin Pine <kevin.pine-ral2JQCrhuEAvxtiuMwx3w@public.gmane.org>
Signed-off-by: Kyle Liddell <kyle.liddell-ral2JQCrhuEAvxtiuMwx3w@public.gmane.org>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn-ral2JQCrhuEAvxtiuMwx3w@public.gmane.org>
Signed-off-by: Mitko Haralanov <mitko.haralanov-ral2JQCrhuEAvxtiuMwx3w@public.gmane.org>
Signed-off-by: Ravi Krishnaswamy <ravi.krishnaswamy-ral2JQCrhuEAvxtiuMwx3w@public.gmane.org>
Signed-off-by: Sadanand Warrier <sadanand.warrier-ral2JQCrhuEAvxtiuMwx3w@public.gmane.org>
Signed-off-by: Sanath Kumar <sanath.s.kumar-ral2JQCrhuEAvxtiuMwx3w@public.gmane.org>
Signed-off-by: Sudeep Dutt <sudeep.dutt-ral2JQCrhuEAvxtiuMwx3w@public.gmane.org>
Signed-off-by: Vlad Danushevsky <vladimir.danusevsky-ral2JQCrhuEAvxtiuMwx3w@public.gmane.org>
---
drivers/infiniband/hw/hfi1/chip.c | 2890 +++++++++++++++++++++++++++++++++++++
1 file changed, 2890 insertions(+)
diff --git a/drivers/infiniband/hw/hfi1/chip.c b/drivers/infiniband/hw/hfi1/chip.c
index 2bb026d..ed03311 100644
--- a/drivers/infiniband/hw/hfi1/chip.c
+++ b/drivers/infiniband/hw/hfi1/chip.c
@@ -2140,3 +2140,2893 @@ static void handle_cce_err(struct hfi1_devdata *dd, u32 unused, u64 reg)
}
}
+/*
+ * Check counters for receive errors that do not have an interrupt
+ * associated with them.
+ */
+#define RCVERR_CHECK_TIME 10
+static void update_rcverr_timer(unsigned long opaque)
+{
+ struct hfi1_devdata *dd = (struct hfi1_devdata *)opaque;
+ struct hfi1_pportdata *ppd = dd->pport;
+ u32 cur_ovfl_cnt = read_dev_cntr(dd, C_RCV_OVF, CNTR_INVALID_VL);
+
+ if (dd->rcv_ovfl_cnt < cur_ovfl_cnt &&
+ ppd->port_error_action & OPA_PI_MASK_EX_BUFFER_OVERRUN) {
+ dd_dev_info(dd, "%s: PortErrorAction bounce\n", __func__);
+ set_link_down_reason(ppd,
+ OPA_LINKDOWN_REASON_EXCESSIVE_BUFFER_OVERRUN, 0,
+ OPA_LINKDOWN_REASON_EXCESSIVE_BUFFER_OVERRUN);
+ start_link(ppd);
+ }
+ dd->rcv_ovfl_cnt = (u32) cur_ovfl_cnt;
+
+ mod_timer(&dd->rcverr_timer, jiffies + HZ * RCVERR_CHECK_TIME);
+}
+
+static int init_rcverr(struct hfi1_devdata *dd)
+{
+ init_timer(&dd->rcverr_timer);
+ dd->rcverr_timer.function = update_rcverr_timer;
+ dd->rcverr_timer.data = (unsigned long) dd;
+ /* Assume the hardware counter has been reset */
+ dd->rcv_ovfl_cnt = 0;
+ return mod_timer(&dd->rcverr_timer, jiffies + HZ * RCVERR_CHECK_TIME);
+}
+
+static void free_rcverr(struct hfi1_devdata *dd)
+{
+ if (dd->rcverr_timer.data)
+ del_timer_sync(&dd->rcverr_timer);
+ dd->rcverr_timer.data = 0;
+}
+
+static void handle_rxe_err(struct hfi1_devdata *dd, u32 unused, u64 reg)
+{
+ char buf[96];
+
+ dd_dev_info(dd, "Receive Error: %s\n",
+ rxe_err_status_string(buf, sizeof(buf), reg));
+
+ if (reg & ALL_RXE_FREEZE_ERR) {
+ int flags = 0;
+
+ /*
+ * Freeze mode recovery is disabled for the errors
+ * in RXE_FREEZE_ABORT_MASK
+ */
+ if (is_a0(dd) && (reg & RXE_FREEZE_ABORT_MASK))
+ flags = FREEZE_ABORT;
+
+ start_freeze_handling(dd->pport, flags);
+ }
+}
+
+static void handle_misc_err(struct hfi1_devdata *dd, u32 unused, u64 reg)
+{
+ char buf[96];
+
+ dd_dev_info(dd, "Misc Error: %s",
+ misc_err_status_string(buf, sizeof(buf), reg));
+}
+
+static void handle_pio_err(struct hfi1_devdata *dd, u32 unused, u64 reg)
+{
+ char buf[96];
+
+ dd_dev_info(dd, "PIO Error: %s\n",
+ pio_err_status_string(buf, sizeof(buf), reg));
+
+ if (reg & ALL_PIO_FREEZE_ERR)
+ start_freeze_handling(dd->pport, 0);
+}
+
+static void handle_sdma_err(struct hfi1_devdata *dd, u32 unused, u64 reg)
+{
+ char buf[96];
+
+ dd_dev_info(dd, "SDMA Error: %s\n",
+ sdma_err_status_string(buf, sizeof(buf), reg));
+
+ if (reg & ALL_SDMA_FREEZE_ERR)
+ start_freeze_handling(dd->pport, 0);
+}
+
+static void count_port_inactive(struct hfi1_devdata *dd)
+{
+ struct hfi1_pportdata *ppd = dd->pport;
+
+ if (ppd->port_xmit_discards < ~(u64)0)
+ ppd->port_xmit_discards++;
+}
+
+/*
+ * We have had a "disallowed packet" error during egress. Determine the
+ * integrity check which failed, and update relevant error counter, etc.
+ *
+ * Note that the SEND_EGRESS_ERR_INFO register has only a single
+ * bit of state per integrity check, and so we can miss the reason for an
+ * egress error if more than one packet fails the same integrity check
+ * since we cleared the corresponding bit in SEND_EGRESS_ERR_INFO.
+ */
+static void handle_send_egress_err_info(struct hfi1_devdata *dd)
+{
+ struct hfi1_pportdata *ppd = dd->pport;
+ u64 src = read_csr(dd, SEND_EGRESS_ERR_SOURCE); /* read first */
+ u64 info = read_csr(dd, SEND_EGRESS_ERR_INFO);
+ char buf[96];
+
+ /* clear down all observed info as quickly as possible after read */
+ write_csr(dd, SEND_EGRESS_ERR_INFO, info);
+
+ dd_dev_info(dd,
+ "Egress Error Info: 0x%llx, %s Egress Error Src 0x%llx\n",
+ info, egress_err_info_string(buf, sizeof(buf), info), src);
+
+ /* Eventually add other counters for each bit */
+
+ if (info & SEND_EGRESS_ERR_INFO_TOO_LONG_IB_PACKET_ERR_SMASK) {
+ if (ppd->port_xmit_discards < ~(u64)0)
+ ppd->port_xmit_discards++;
+ }
+}
+
+/*
+ * Input value is a bit position within the SEND_EGRESS_ERR_STATUS
+ * register. Does it represent a 'port inactive' error?
+ */
+static inline int port_inactive_err(u64 posn)
+{
+ return (posn >= SEES(TX_LINKDOWN) &&
+ posn <= SEES(TX_INCORRECT_LINK_STATE));
+}
+
+/*
+ * Input value is a bit position within the SEND_EGRESS_ERR_STATUS
+ * register. Does it represent a 'disallowed packet' error?
+ */
+static inline int disallowed_pkt_err(u64 posn)
+{
+ return (posn >= SEES(TX_SDMA0_DISALLOWED_PACKET) &&
+ posn <= SEES(TX_SDMA15_DISALLOWED_PACKET));
+}
+
+static void handle_egress_err(struct hfi1_devdata *dd, u32 unused, u64 reg)
+{
+ u64 reg_copy = reg, handled = 0;
+ char buf[96];
+
+ if (reg & ALL_TXE_EGRESS_FREEZE_ERR)
+ start_freeze_handling(dd->pport, 0);
+ if (is_a0(dd) && (reg &
+ SEND_EGRESS_ERR_STATUS_TX_CREDIT_RETURN_VL_ERR_SMASK)
+ && (dd->icode != ICODE_FUNCTIONAL_SIMULATOR))
+ start_freeze_handling(dd->pport, 0);
+
+ while (reg_copy) {
+ int posn = fls64(reg_copy);
+ /*
+ * fls64() returns a 1-based offset, but we generally
+ * want 0-based offsets.
+ */
+ int shift = posn - 1;
+
+ if (port_inactive_err(shift)) {
+ count_port_inactive(dd);
+ handled |= (1ULL << shift);
+ } else if (disallowed_pkt_err(shift)) {
+ handle_send_egress_err_info(dd);
+ handled |= (1ULL << shift);
+ }
+ clear_bit(shift, (unsigned long *)®_copy);
+ }
+
+ reg &= ~handled;
+
+ if (reg)
+ dd_dev_info(dd, "Egress Error: %s\n",
+ egress_err_status_string(buf, sizeof(buf), reg));
+}
+
+static void handle_txe_err(struct hfi1_devdata *dd, u32 unused, u64 reg)
+{
+ char buf[96];
+
+ dd_dev_info(dd, "Send Error: %s\n",
+ send_err_status_string(buf, sizeof(buf), reg));
+
+}
+
+/*
+ * The maximum number of times the error clear down will loop before
+ * blocking a repeating error. This value is arbitrary.
+ */
+#define MAX_CLEAR_COUNT 20
+
+/*
+ * Clear and handle an error register. All error interrupts are funneled
+ * through here to have a central location to correctly handle single-
+ * or multi-shot errors.
+ *
+ * For non per-context registers, call this routine with a context value
+ * of 0 so the per-context offset is zero.
+ *
+ * If the handler loops too many times, assume that something is wrong
+ * and can't be fixed, so mask the error bits.
+ */
+static void interrupt_clear_down(struct hfi1_devdata *dd,
+ u32 context,
+ const struct err_reg_info *eri)
+{
+ u64 reg;
+ u32 count;
+
+ /* read in a loop until no more errors are seen */
+ count = 0;
+ while (1) {
+ reg = read_kctxt_csr(dd, context, eri->status);
+ if (reg == 0)
+ break;
+ write_kctxt_csr(dd, context, eri->clear, reg);
+ if (likely(eri->handler))
+ eri->handler(dd, context, reg);
+ count++;
+ if (count > MAX_CLEAR_COUNT) {
+ u64 mask;
+
+ dd_dev_err(dd, "Repeating %s bits 0x%llx - masking\n",
+ eri->desc, reg);
+ /*
+ * Read-modify-write so any other masked bits
+ * remain masked.
+ */
+ mask = read_kctxt_csr(dd, context, eri->mask);
+ mask &= ~reg;
+ write_kctxt_csr(dd, context, eri->mask, mask);
+ break;
+ }
+ }
+}
+
+/*
+ * CCE block "misc" interrupt. Source is < 16.
+ */
+static void is_misc_err_int(struct hfi1_devdata *dd, unsigned int source)
+{
+ const struct err_reg_info *eri = &misc_errs[source];
+
+ if (eri->handler) {
+ interrupt_clear_down(dd, 0, eri);
+ } else {
+ dd_dev_err(dd, "Unexpected misc interrupt (%u) - reserved\n",
+ source);
+ }
+}
+
+static char *send_context_err_status_string(char *buf, int buf_len, u64 flags)
+{
+ return flag_string(buf, buf_len, flags,
+ sc_err_status_flags, ARRAY_SIZE(sc_err_status_flags));
+}
+
+/*
+ * Send context error interrupt. Source (hw_context) is < 160.
+ *
+ * All send context errors cause the send context to halt. The normal
+ * clear-down mechanism cannot be used because we cannot clear the
+ * error bits until several other long-running items are done first.
+ * This is OK because with the context halted, nothing else is going
+ * to happen on it anyway.
+ */
+static void is_sendctxt_err_int(struct hfi1_devdata *dd,
+ unsigned int hw_context)
+{
+ struct send_context_info *sci;
+ struct send_context *sc;
+ char flags[96];
+ u64 status;
+ u32 sw_index;
+
+ sw_index = dd->hw_to_sw[hw_context];
+ if (sw_index >= dd->num_send_contexts) {
+ dd_dev_err(dd,
+ "out of range sw index %u for send context %u\n",
+ sw_index, hw_context);
+ return;
+ }
+ sci = &dd->send_contexts[sw_index];
+ sc = sci->sc;
+ if (!sc) {
+ dd_dev_err(dd, "%s: context %u(%u): no sc?\n", __func__,
+ sw_index, hw_context);
+ return;
+ }
+
+ /* tell the software that a halt has begun */
+ sc_stop(sc, SCF_HALTED);
+
+ status = read_kctxt_csr(dd, hw_context, SEND_CTXT_ERR_STATUS);
+
+ dd_dev_info(dd, "Send Context %u(%u) Error: %s\n", sw_index, hw_context,
+ send_context_err_status_string(flags, sizeof(flags), status));
+
+ if (status & SEND_CTXT_ERR_STATUS_PIO_DISALLOWED_PACKET_ERR_SMASK)
+ handle_send_egress_err_info(dd);
+
+ /*
+ * Automatically restart halted kernel contexts out of interrupt
+ * context. User contexts must ask the driver to restart the context.
+ */
+ if (sc->type != SC_USER)
+ queue_work(dd->pport->hfi1_wq, &sc->halt_work);
+}
+
+static void handle_sdma_eng_err(struct hfi1_devdata *dd,
+ unsigned int source, u64 status)
+{
+ struct sdma_engine *sde;
+
+ sde = &dd->per_sdma[source];
+ /* BUG_ON(source != 0); */
+#ifdef CONFIG_SDMA_VERBOSITY
+ dd_dev_err(sde->dd, "CONFIG SDMA(%u) %s:%d %s()\n", sde->this_idx,
+ slashstrip(__FILE__), __LINE__, __func__);
+ dd_dev_err(sde->dd, "CONFIG SDMA(%u) source: %u status 0x%llx\n",
+ sde->this_idx, source, (unsigned long long)status);
+#endif
+ sdma_engine_error(sde, status);
+}
+
+/*
+ * CCE block SDMA error interrupt. Source is < 16.
+ */
+static void is_sdma_eng_err_int(struct hfi1_devdata *dd, unsigned int source)
+{
+#ifdef CONFIG_SDMA_VERBOSITY
+ struct sdma_engine *sde = &dd->per_sdma[source];
+
+ dd_dev_err(dd, "CONFIG SDMA(%u) %s:%d %s()\n", sde->this_idx,
+ slashstrip(__FILE__), __LINE__, __func__);
+ dd_dev_err(dd, "CONFIG SDMA(%u) source: %u\n", sde->this_idx,
+ source);
+ sdma_dumpstate(sde);
+#endif
+ interrupt_clear_down(dd, source, &sdma_eng_err);
+}
+
+/*
+ * CCE block "various" interrupt. Source is < 8.
+ */
+static void is_various_int(struct hfi1_devdata *dd, unsigned int source)
+{
+ const struct err_reg_info *eri = &various_err[source];
+
+ /*
+ * TCritInt cannot go through interrupt_clear_down()
+ * because it is not a second tier interrupt. The handler
+ * should be called directly.
+ */
+ if (source == TCRIT_INT_SOURCE)
+ handle_temp_err(dd);
+ else if (eri->handler)
+ interrupt_clear_down(dd, 0, eri);
+ else
+ dd_dev_info(dd,
+ "%s: Unimplemented/reserved interrupt %d\n",
+ __func__, source);
+}
+
+static void handle_qsfp_int(struct hfi1_devdata *dd, u32 src_ctx, u64 reg)
+{
+ /* source is always zero */
+ struct hfi1_pportdata *ppd = dd->pport;
+ unsigned long flags;
+ u64 qsfp_int_mgmt = (u64)(QSFP_HFI0_INT_N | QSFP_HFI0_MODPRST_N);
+
+ if (reg & QSFP_HFI0_MODPRST_N) {
+
+ dd_dev_info(dd, "%s: ModPresent triggered QSFP interrupt\n",
+ __func__);
+
+ if (!qsfp_mod_present(ppd)) {
+ ppd->driver_link_ready = 0;
+ /*
+ * Cable removed, reset all our information about the
+ * cache and cable capabilities
+ */
+
+ spin_lock_irqsave(&ppd->qsfp_info.qsfp_lock, flags);
+ /*
+ * We don't set cache_refresh_required here as we expect
+ * an interrupt when a cable is inserted
+ */
+ ppd->qsfp_info.cache_valid = 0;
+ ppd->qsfp_info.qsfp_interrupt_functional = 0;
+ spin_unlock_irqrestore(&ppd->qsfp_info.qsfp_lock,
+ flags);
+ write_csr(dd,
+ dd->hfi1_id ?
+ ASIC_QSFP2_INVERT :
+ ASIC_QSFP1_INVERT,
+ qsfp_int_mgmt);
+ if (ppd->host_link_state == HLS_DN_POLL) {
+ /*
+ * The link is still in POLL. This means
+ * that the normal link down processing
+ * will not happen. We have to do it here
+ * before turning the DC off.
+ */
+ queue_work(ppd->hfi1_wq, &ppd->link_down_work);
+ }
+ } else {
+ spin_lock_irqsave(&ppd->qsfp_info.qsfp_lock, flags);
+ ppd->qsfp_info.cache_valid = 0;
+ ppd->qsfp_info.cache_refresh_required = 1;
+ spin_unlock_irqrestore(&ppd->qsfp_info.qsfp_lock,
+ flags);
+
+ qsfp_int_mgmt &= ~(u64)QSFP_HFI0_MODPRST_N;
+ write_csr(dd,
+ dd->hfi1_id ?
+ ASIC_QSFP2_INVERT :
+ ASIC_QSFP1_INVERT,
+ qsfp_int_mgmt);
+ }
+ }
+
+ if (reg & QSFP_HFI0_INT_N) {
+
+ dd_dev_info(dd, "%s: IntN triggered QSFP interrupt\n",
+ __func__);
+ spin_lock_irqsave(&ppd->qsfp_info.qsfp_lock, flags);
+ ppd->qsfp_info.check_interrupt_flags = 1;
+ ppd->qsfp_info.qsfp_interrupt_functional = 1;
+ spin_unlock_irqrestore(&ppd->qsfp_info.qsfp_lock, flags);
+ }
+
+ /* Schedule the QSFP work only if there is a cable attached. */
+ if (qsfp_mod_present(ppd))
+ queue_work(ppd->hfi1_wq, &ppd->qsfp_info.qsfp_work);
+}
+
+static int request_host_lcb_access(struct hfi1_devdata *dd)
+{
+ int ret;
+
+ ret = do_8051_command(dd, HCMD_MISC,
+ (u64)HCMD_MISC_REQUEST_LCB_ACCESS << LOAD_DATA_FIELD_ID_SHIFT,
+ NULL);
+ if (ret != HCMD_SUCCESS) {
+ dd_dev_err(dd, "%s: command failed with error %d\n",
+ __func__, ret);
+ }
+ return ret == HCMD_SUCCESS ? 0 : -EBUSY;
+}
+
+static int request_8051_lcb_access(struct hfi1_devdata *dd)
+{
+ int ret;
+
+ ret = do_8051_command(dd, HCMD_MISC,
+ (u64)HCMD_MISC_GRANT_LCB_ACCESS << LOAD_DATA_FIELD_ID_SHIFT,
+ NULL);
+ if (ret != HCMD_SUCCESS) {
+ dd_dev_err(dd, "%s: command failed with error %d\n",
+ __func__, ret);
+ }
+ return ret == HCMD_SUCCESS ? 0 : -EBUSY;
+}
+
+/*
+ * Set the LCB selector - allow host access. The DCC selector always
+ * points to the host.
+ */
+static inline void set_host_lcb_access(struct hfi1_devdata *dd)
+{
+ write_csr(dd, DC_DC8051_CFG_CSR_ACCESS_SEL,
+ DC_DC8051_CFG_CSR_ACCESS_SEL_DCC_SMASK
+ | DC_DC8051_CFG_CSR_ACCESS_SEL_LCB_SMASK);
+}
+
+/*
+ * Clear the LCB selector - allow 8051 access. The DCC selector always
+ * points to the host.
+ */
+static inline void set_8051_lcb_access(struct hfi1_devdata *dd)
+{
+ write_csr(dd, DC_DC8051_CFG_CSR_ACCESS_SEL,
+ DC_DC8051_CFG_CSR_ACCESS_SEL_DCC_SMASK);
+}
+
+/*
+ * Acquire LCB access from the 8051. If the host already has access,
+ * just increment a counter. Otherwise, inform the 8051 that the
+ * host is taking access.
+ *
+ * Returns:
+ * 0 on success
+ * -EBUSY if the 8051 has control and cannot be disturbed
+ * -errno if unable to acquire access from the 8051
+ */
+int acquire_lcb_access(struct hfi1_devdata *dd, int sleep_ok)
+{
+ struct hfi1_pportdata *ppd = dd->pport;
+ int ret = 0;
+
+ /*
+ * Use the host link state lock so the operation of this routine
+ * { link state check, selector change, count increment } can occur
+ * as a unit against a link state change. Otherwise there is a
+ * race between the state change and the count increment.
+ */
+ if (sleep_ok) {
+ mutex_lock(&ppd->hls_lock);
+ } else {
+ while (mutex_trylock(&ppd->hls_lock) == EBUSY)
+ udelay(1);
+ }
+
+ /* this access is valid only when the link is up */
+ if ((ppd->host_link_state & HLS_UP) == 0) {
+ dd_dev_info(dd, "%s: link state %s not up\n",
+ __func__, link_state_name(ppd->host_link_state));
+ ret = -EBUSY;
+ goto done;
+ }
+
+ if (dd->lcb_access_count == 0) {
+ ret = request_host_lcb_access(dd);
+ if (ret) {
+ dd_dev_err(dd,
+ "%s: unable to acquire LCB access, err %d\n",
+ __func__, ret);
+ goto done;
+ }
+ set_host_lcb_access(dd);
+ }
+ dd->lcb_access_count++;
+done:
+ mutex_unlock(&ppd->hls_lock);
+ return ret;
+}
+
+/*
+ * Release LCB access by decrementing the use count. If the count is moving
+ * from 1 to 0, inform 8051 that it has control back.
+ *
+ * Returns:
+ * 0 on success
+ * -errno if unable to release access to the 8051
+ */
+int release_lcb_access(struct hfi1_devdata *dd, int sleep_ok)
+{
+ int ret = 0;
+
+ /*
+ * Use the host link state lock because the acquire needed it.
+ * Here, we only need to keep { selector change, count decrement }
+ * as a unit.
+ */
+ if (sleep_ok) {
+ mutex_lock(&dd->pport->hls_lock);
+ } else {
+ while (mutex_trylock(&dd->pport->hls_lock) == EBUSY)
+ udelay(1);
+ }
+
+ if (dd->lcb_access_count == 0) {
+ dd_dev_err(dd, "%s: LCB access count is zero. Skipping.\n",
+ __func__);
+ goto done;
+ }
+
+ if (dd->lcb_access_count == 1) {
+ set_8051_lcb_access(dd);
+ ret = request_8051_lcb_access(dd);
+ if (ret) {
+ dd_dev_err(dd,
+ "%s: unable to release LCB access, err %d\n",
+ __func__, ret);
+ /* restore host access if the grant didn't work */
+ set_host_lcb_access(dd);
+ goto done;
+ }
+ }
+ dd->lcb_access_count--;
+done:
+ mutex_unlock(&dd->pport->hls_lock);
+ return ret;
+}
+
+/*
+ * Initialize LCB access variables and state. Called during driver load,
+ * after most of the initialization is finished.
+ *
+ * The DC default is LCB access on for the host. The driver defaults to
+ * leaving access to the 8051. Assign access now - this constrains the call
+ * to this routine to be after all LCB set-up is done. In particular, after
+ * hf1_init_dd() -> set_up_interrupts() -> clear_all_interrupts()
+ */
+static void init_lcb_access(struct hfi1_devdata *dd)
+{
+ dd->lcb_access_count = 0;
+}
+
+/*
+ * Write a response back to a 8051 request.
+ */
+static void hreq_response(struct hfi1_devdata *dd, u8 return_code, u16 rsp_data)
+{
+ write_csr(dd, DC_DC8051_CFG_EXT_DEV_0,
+ DC_DC8051_CFG_EXT_DEV_0_COMPLETED_SMASK
+ | (u64)return_code << DC_DC8051_CFG_EXT_DEV_0_RETURN_CODE_SHIFT
+ | (u64)rsp_data << DC_DC8051_CFG_EXT_DEV_0_RSP_DATA_SHIFT);
+}
+
+/*
+ * Handle requests from the 8051.
+ */
+static void handle_8051_request(struct hfi1_devdata *dd)
+{
+ u64 reg;
+ u16 data;
+ u8 type;
+
+ reg = read_csr(dd, DC_DC8051_CFG_EXT_DEV_1);
+ if ((reg & DC_DC8051_CFG_EXT_DEV_1_REQ_NEW_SMASK) == 0)
+ return; /* no request */
+
+ /* zero out COMPLETED so the response is seen */
+ write_csr(dd, DC_DC8051_CFG_EXT_DEV_0, 0);
+
+ /* extract request details */
+ type = (reg >> DC_DC8051_CFG_EXT_DEV_1_REQ_TYPE_SHIFT)
+ & DC_DC8051_CFG_EXT_DEV_1_REQ_TYPE_MASK;
+ data = (reg >> DC_DC8051_CFG_EXT_DEV_1_REQ_DATA_SHIFT)
+ & DC_DC8051_CFG_EXT_DEV_1_REQ_DATA_MASK;
+
+ switch (type) {
+ case HREQ_LOAD_CONFIG:
+ case HREQ_SAVE_CONFIG:
+ case HREQ_READ_CONFIG:
+ case HREQ_SET_TX_EQ_ABS:
+ case HREQ_SET_TX_EQ_REL:
+ case HREQ_ENABLE:
+ dd_dev_info(dd, "8051 request: request 0x%x not supported\n",
+ type);
+ hreq_response(dd, HREQ_NOT_SUPPORTED, 0);
+ break;
+
+ case HREQ_CONFIG_DONE:
+ hreq_response(dd, HREQ_SUCCESS, 0);
+ break;
+
+ case HREQ_INTERFACE_TEST:
+ hreq_response(dd, HREQ_SUCCESS, data);
+ break;
+
+ default:
+ dd_dev_err(dd, "8051 request: unknown request 0x%x\n", type);
+ hreq_response(dd, HREQ_NOT_SUPPORTED, 0);
+ break;
+ }
+}
+
+static void write_global_credit(struct hfi1_devdata *dd,
+ u8 vau, u16 total, u16 shared)
+{
+ write_csr(dd, SEND_CM_GLOBAL_CREDIT,
+ ((u64)total
+ << SEND_CM_GLOBAL_CREDIT_TOTAL_CREDIT_LIMIT_SHIFT)
+ | ((u64)shared
+ << SEND_CM_GLOBAL_CREDIT_SHARED_LIMIT_SHIFT)
+ | ((u64)vau << SEND_CM_GLOBAL_CREDIT_AU_SHIFT));
+}
+
+/*
+ * Set up initial VL15 credits of the remote. Assumes the rest of
+ * the CM credit registers are zero from a previous global or credit reset .
+ */
+void set_up_vl15(struct hfi1_devdata *dd, u8 vau, u16 vl15buf)
+{
+ /* leave shared count at zero for both global and VL15 */
+ write_global_credit(dd, vau, vl15buf, 0);
+ write_csr(dd, SEND_CM_CREDIT_VL15, (u64)vl15buf
+ << SEND_CM_CREDIT_VL15_DEDICATED_LIMIT_VL_SHIFT);
+}
+
+/*
+ * Zero all credit details from the previous connection and
+ * reset the CM manager's internal counters.
+ */
+void reset_link_credits(struct hfi1_devdata *dd)
+{
+ int i;
+
+ /* remove all previous VL credit limits */
+ for (i = 0; i < TXE_NUM_DATA_VL; i++)
+ write_csr(dd, SEND_CM_CREDIT_VL + (8*i), 0);
+ write_csr(dd, SEND_CM_CREDIT_VL15, 0);
+ write_global_credit(dd, 0, 0, 0);
+ /* reset the CM block */
+ pio_send_control(dd, PSC_CM_RESET);
+}
+
+/* convert a vCU to a CU */
+static u32 vcu_to_cu(u8 vcu)
+{
+ return 1 << vcu;
+}
+
+/* convert a CU to a vCU */
+static u8 cu_to_vcu(u32 cu)
+{
+ return ilog2(cu);
+}
+
+/* convert a vAU to an AU */
+static u32 vau_to_au(u8 vau)
+{
+ return 8 * (1 << vau);
+}
+
+static void set_linkup_defaults(struct hfi1_pportdata *ppd)
+{
+ ppd->sm_trap_qp = 0x0;
+ ppd->sa_qp = 0x1;
+}
+
+/*
+ * Graceful LCB shutdown. This leaves the LCB FIFOs in reset.
+ */
+static void lcb_shutdown(struct hfi1_devdata *dd, int abort)
+{
+ u64 reg;
+
+ /* clear lcb run: LCB_CFG_RUN.EN = 0 */
+ write_csr(dd, DC_LCB_CFG_RUN, 0);
+ /* set tx fifo reset: LCB_CFG_TX_FIFOS_RESET.VAL = 1 */
+ write_csr(dd, DC_LCB_CFG_TX_FIFOS_RESET,
+ 1ull << DC_LCB_CFG_TX_FIFOS_RESET_VAL_SHIFT);
+ /* set dcc reset csr: DCC_CFG_RESET.{reset_lcb,reset_rx_fpe} = 1 */
+ dd->lcb_err_en = read_csr(dd, DC_LCB_ERR_EN);
+ reg = read_csr(dd, DCC_CFG_RESET);
+ write_csr(dd, DCC_CFG_RESET,
+ reg
+ | (1ull << DCC_CFG_RESET_RESET_LCB_SHIFT)
+ | (1ull << DCC_CFG_RESET_RESET_RX_FPE_SHIFT));
+ (void) read_csr(dd, DCC_CFG_RESET); /* make sure the write completed */
+ if (!abort) {
+ udelay(1); /* must hold for the longer of 16cclks or 20ns */
+ write_csr(dd, DCC_CFG_RESET, reg);
+ write_csr(dd, DC_LCB_ERR_EN, dd->lcb_err_en);
+ }
+}
+
+/*
+ * This routine should be called after the link has been transitioned to
+ * OFFLINE (OFFLINE state has the side effect of putting the SerDes into
+ * reset).
+ *
+ * The expectation is that the caller of this routine would have taken
+ * care of properly transitioning the link into the correct state.
+ */
+static void dc_shutdown(struct hfi1_devdata *dd)
+{
+ unsigned long flags;
+
+ spin_lock_irqsave(&dd->dc8051_lock, flags);
+ if (dd->dc_shutdown) {
+ spin_unlock_irqrestore(&dd->dc8051_lock, flags);
+ return;
+ }
+ dd->dc_shutdown = 1;
+ spin_unlock_irqrestore(&dd->dc8051_lock, flags);
+ /* Shutdown the LCB */
+ lcb_shutdown(dd, 1);
+ /* Going to OFFLINE would have causes the 8051 to put the
+ * SerDes into reset already. Just need to shut down the 8051,
+ * itself. */
+ write_csr(dd, DC_DC8051_CFG_RST, 0x1);
+}
+
+/* Calling this after the DC has been brought out of reset should not
+ * do any damage. */
+static void dc_start(struct hfi1_devdata *dd)
+{
+ unsigned long flags;
+ int ret;
+
+ spin_lock_irqsave(&dd->dc8051_lock, flags);
+ if (!dd->dc_shutdown)
+ goto done;
+ spin_unlock_irqrestore(&dd->dc8051_lock, flags);
+ /* Take the 8051 out of reset */
+ write_csr(dd, DC_DC8051_CFG_RST, 0ull);
+ /* Wait until 8051 is ready */
+ ret = wait_fm_ready(dd, TIMEOUT_8051_START);
+ if (ret) {
+ dd_dev_err(dd, "%s: timeout starting 8051 firmware\n",
+ __func__);
+ }
+ /* Take away reset for LCB and RX FPE (set in lcb_shutdown). */
+ write_csr(dd, DCC_CFG_RESET, 0x10);
+ /* lcb_shutdown() with abort=1 does not restore these */
+ write_csr(dd, DC_LCB_ERR_EN, dd->lcb_err_en);
+ spin_lock_irqsave(&dd->dc8051_lock, flags);
+ dd->dc_shutdown = 0;
+done:
+ spin_unlock_irqrestore(&dd->dc8051_lock, flags);
+}
+
+/*
+ * These LCB adjustments are for the Aurora SerDes core in the FPGA.
+ */
+static void adjust_lcb_for_fpga_serdes(struct hfi1_devdata *dd)
+{
+ u64 rx_radr, tx_radr;
+ u32 version;
+
+ if (dd->icode != ICODE_FPGA_EMULATION)
+ return;
+
+ /*
+ * These LCB defaults on emulator _s are good, nothing to do here:
+ * LCB_CFG_TX_FIFOS_RADR
+ * LCB_CFG_RX_FIFOS_RADR
+ * LCB_CFG_LN_DCLK
+ * LCB_CFG_IGNORE_LOST_RCLK
+ */
+ if (is_emulator_s(dd))
+ return;
+ /* else this is _p */
+
+ version = emulator_rev(dd);
+ if (!is_a0(dd))
+ version = 0x2d; /* all B0 use 0x2d or higher settings */
+
+ if (version <= 0x12) {
+ /* release 0x12 and below */
+
+ /*
+ * LCB_CFG_RX_FIFOS_RADR.RST_VAL = 0x9
+ * LCB_CFG_RX_FIFOS_RADR.OK_TO_JUMP_VAL = 0x9
+ * LCB_CFG_RX_FIFOS_RADR.DO_NOT_JUMP_VAL = 0xa
+ */
+ rx_radr =
+ 0xaull << DC_LCB_CFG_RX_FIFOS_RADR_DO_NOT_JUMP_VAL_SHIFT
+ | 0x9ull << DC_LCB_CFG_RX_FIFOS_RADR_OK_TO_JUMP_VAL_SHIFT
+ | 0x9ull << DC_LCB_CFG_RX_FIFOS_RADR_RST_VAL_SHIFT;
+ /*
+ * LCB_CFG_TX_FIFOS_RADR.ON_REINIT = 0 (default)
+ * LCB_CFG_TX_FIFOS_RADR.RST_VAL = 6
+ */
+ tx_radr = 6ull << DC_LCB_CFG_TX_FIFOS_RADR_RST_VAL_SHIFT;
+ } else if (version <= 0x18) {
+ /* release 0x13 up to 0x18 */
+ /* LCB_CFG_RX_FIFOS_RADR = 0x988 */
+ rx_radr =
+ 0x9ull << DC_LCB_CFG_RX_FIFOS_RADR_DO_NOT_JUMP_VAL_SHIFT
+ | 0x8ull << DC_LCB_CFG_RX_FIFOS_RADR_OK_TO_JUMP_VAL_SHIFT
+ | 0x8ull << DC_LCB_CFG_RX_FIFOS_RADR_RST_VAL_SHIFT;
+ tx_radr = 7ull << DC_LCB_CFG_TX_FIFOS_RADR_RST_VAL_SHIFT;
+ } else if (version == 0x19) {
+ /* release 0x19 */
+ /* LCB_CFG_RX_FIFOS_RADR = 0xa99 */
+ rx_radr =
+ 0xAull << DC_LCB_CFG_RX_FIFOS_RADR_DO_NOT_JUMP_VAL_SHIFT
+ | 0x9ull << DC_LCB_CFG_RX_FIFOS_RADR_OK_TO_JUMP_VAL_SHIFT
+ | 0x9ull << DC_LCB_CFG_RX_FIFOS_RADR_RST_VAL_SHIFT;
+ tx_radr = 3ull << DC_LCB_CFG_TX_FIFOS_RADR_RST_VAL_SHIFT;
+ } else if (version == 0x1a) {
+ /* release 0x1a */
+ /* LCB_CFG_RX_FIFOS_RADR = 0x988 */
+ rx_radr =
+ 0x9ull << DC_LCB_CFG_RX_FIFOS_RADR_DO_NOT_JUMP_VAL_SHIFT
+ | 0x8ull << DC_LCB_CFG_RX_FIFOS_RADR_OK_TO_JUMP_VAL_SHIFT
+ | 0x8ull << DC_LCB_CFG_RX_FIFOS_RADR_RST_VAL_SHIFT;
+ tx_radr = 7ull << DC_LCB_CFG_TX_FIFOS_RADR_RST_VAL_SHIFT;
+ write_csr(dd, DC_LCB_CFG_LN_DCLK, 1ull);
+ } else {
+ /* release 0x1b and higher */
+ /* LCB_CFG_RX_FIFOS_RADR = 0x877 */
+ rx_radr =
+ 0x8ull << DC_LCB_CFG_RX_FIFOS_RADR_DO_NOT_JUMP_VAL_SHIFT
+ | 0x7ull << DC_LCB_CFG_RX_FIFOS_RADR_OK_TO_JUMP_VAL_SHIFT
+ | 0x7ull << DC_LCB_CFG_RX_FIFOS_RADR_RST_VAL_SHIFT;
+ tx_radr = 3ull << DC_LCB_CFG_TX_FIFOS_RADR_RST_VAL_SHIFT;
+ }
+
+ write_csr(dd, DC_LCB_CFG_RX_FIFOS_RADR, rx_radr);
+ /* LCB_CFG_IGNORE_LOST_RCLK.EN = 1 */
+ write_csr(dd, DC_LCB_CFG_IGNORE_LOST_RCLK,
+ DC_LCB_CFG_IGNORE_LOST_RCLK_EN_SMASK);
+ write_csr(dd, DC_LCB_CFG_TX_FIFOS_RADR, tx_radr);
+}
+
+/*
+ * Handle a SMA idle message
+ *
+ * This is a work-queue function outside of the interrupt.
+ */
+void handle_sma_message(struct work_struct *work)
+{
+ struct hfi1_pportdata *ppd = container_of(work, struct hfi1_pportdata,
+ sma_message_work);
+ struct hfi1_devdata *dd = ppd->dd;
+ u64 msg;
+ int ret;
+
+ /* msg is bytes 1-4 of the 40-bit idle message - the command code
+ is stripped off */
+ ret = read_idle_sma(dd, &msg);
+ if (ret)
+ return;
+ dd_dev_info(dd, "%s: SMA message 0x%llx\n", __func__, msg);
+ /*
+ * React to the SMA message. Byte[1] (0 for us) is the command.
+ */
+ switch (msg & 0xff) {
+ case SMA_IDLE_ARM:
+ /*
+ * See OPAv1 table 9-14 - HFI and External Switch Ports Key
+ * State Transitions
+ *
+ * Only expected in INIT or ARMED, discard otherwise.
+ */
+ if (ppd->host_link_state & (HLS_UP_INIT | HLS_UP_ARMED))
+ ppd->neighbor_normal = 1;
+ break;
+ case SMA_IDLE_ACTIVE:
+ /*
+ * See OPAv1 table 9-14 - HFI and External Switch Ports Key
+ * State Transitions
+ *
+ * Can activate the node. Discard otherwise.
+ */
+ if (ppd->host_link_state == HLS_UP_ARMED
+ && ppd->is_active_optimize_enabled) {
+ ppd->neighbor_normal = 1;
+ ret = set_link_state(ppd, HLS_UP_ACTIVE);
+ if (ret)
+ dd_dev_err(
+ dd,
+ "%s: received Active SMA idle message, couldn't set link to Active\n",
+ __func__);
+ }
+ break;
+ default:
+ dd_dev_err(dd,
+ "%s: received unexpected SMA idle message 0x%llx\n",
+ __func__, msg);
+ break;
+ }
+}
+
+static void adjust_rcvctrl(struct hfi1_devdata *dd, u64 add, u64 clear)
+{
+ u64 rcvctrl;
+ unsigned long flags;
+
+ spin_lock_irqsave(&dd->rcvctrl_lock, flags);
+ rcvctrl = read_csr(dd, RCV_CTRL);
+ rcvctrl |= add;
+ rcvctrl &= ~clear;
+ write_csr(dd, RCV_CTRL, rcvctrl);
+ spin_unlock_irqrestore(&dd->rcvctrl_lock, flags);
+}
+
+static inline void add_rcvctrl(struct hfi1_devdata *dd, u64 add)
+{
+ adjust_rcvctrl(dd, add, 0);
+}
+
+static inline void clear_rcvctrl(struct hfi1_devdata *dd, u64 clear)
+{
+ adjust_rcvctrl(dd, 0, clear);
+}
+
+/*
+ * Called from all interrupt handlers to start handling an SPC freeze.
+ */
+void start_freeze_handling(struct hfi1_pportdata *ppd, int flags)
+{
+ struct hfi1_devdata *dd = ppd->dd;
+ struct send_context *sc;
+ int i;
+
+ if (flags & FREEZE_SELF)
+ write_csr(dd, CCE_CTRL, CCE_CTRL_SPC_FREEZE_SMASK);
+
+ /* enter frozen mode */
+ dd->flags |= HFI1_FROZEN;
+
+ /* notify all SDMA engines that they are going into a freeze */
+ sdma_freeze_notify(dd, !!(flags & FREEZE_LINK_DOWN));
+
+ /* do halt pre-handling on all enabled send contexts */
+ for (i = 0; i < dd->num_send_contexts; i++) {
+ sc = dd->send_contexts[i].sc;
+ if (sc && (sc->flags & SCF_ENABLED))
+ sc_stop(sc, SCF_FROZEN | SCF_HALTED);
+ }
+
+ /* Send context are frozen. Notify user space */
+ hfi1_set_uevent_bits(ppd, _HFI1_EVENT_FROZEN_BIT);
+
+ if (flags & FREEZE_ABORT) {
+ dd_dev_err(dd,
+ "Aborted freeze recovery. Please REBOOT system\n");
+ return;
+ }
+ /* queue non-interrupt handler */
+ queue_work(ppd->hfi1_wq, &ppd->freeze_work);
+}
+
+/*
+ * Wait until all 4 sub-blocks indicate that they have frozen or unfrozen,
+ * depending on the "freeze" parameter.
+ *
+ * No need to return an error if it times out, our only option
+ * is to proceed anyway.
+ */
+static void wait_for_freeze_status(struct hfi1_devdata *dd, int freeze)
+{
+ unsigned long timeout;
+ u64 reg;
+
+ timeout = jiffies + msecs_to_jiffies(FREEZE_STATUS_TIMEOUT);
+ while (1) {
+ reg = read_csr(dd, CCE_STATUS);
+ if (freeze) {
+ /* waiting until all indicators are set */
+ if ((reg & ALL_FROZE) == ALL_FROZE)
+ return; /* all done */
+ } else {
+ /* waiting until all indicators are clear */
+ if ((reg & ALL_FROZE) == 0)
+ return; /* all done */
+ }
+
+ if (time_after(jiffies, timeout)) {
+ dd_dev_err(dd,
+ "Time out waiting for SPC %sfreeze, bits 0x%llx, expecting 0x%llx, continuing",
+ freeze ? "" : "un",
+ reg & ALL_FROZE,
+ freeze ? ALL_FROZE : 0ull);
+ return;
+ }
+ usleep_range(80, 120);
+ }
+}
+
+/*
+ * Do all freeze handling for the RXE block.
+ */
+static void rxe_freeze(struct hfi1_devdata *dd)
+{
+ int i;
+
+ /* disable port */
+ clear_rcvctrl(dd, RCV_CTRL_RCV_PORT_ENABLE_SMASK);
+
+ /* disable all receive contexts */
+ for (i = 0; i < dd->num_rcv_contexts; i++)
+ hfi1_rcvctrl(dd, HFI1_RCVCTRL_CTXT_DIS, i);
+}
+
+/*
+ * Unfreeze handling for the RXE block - kernel contexts only.
+ * This will also enable the port. User contexts will do unfreeze
+ * handling on a per-context basis as they call into the driver.
+ *
+ */
+static void rxe_kernel_unfreeze(struct hfi1_devdata *dd)
+{
+ int i;
+
+ /* enable all kernel contexts */
+ for (i = 0; i < dd->n_krcv_queues; i++)
+ hfi1_rcvctrl(dd, HFI1_RCVCTRL_CTXT_ENB, i);
+
+ /* enable port */
+ add_rcvctrl(dd, RCV_CTRL_RCV_PORT_ENABLE_SMASK);
+}
+
+/*
+ * Non-interrupt SPC freeze handling.
+ *
+ * This is a work-queue function outside of the triggering interrupt.
+ */
+void handle_freeze(struct work_struct *work)
+{
+ struct hfi1_pportdata *ppd = container_of(work, struct hfi1_pportdata,
+ freeze_work);
+ struct hfi1_devdata *dd = ppd->dd;
+
+ /* wait for freeze indicators on all affected blocks */
+ dd_dev_info(dd, "Entering SPC freeze\n");
+ wait_for_freeze_status(dd, 1);
+
+ /* SPC is now frozen */
+
+ /* do send PIO freeze steps */
+ pio_freeze(dd);
+
+ /* do send DMA freeze steps */
+ sdma_freeze(dd);
+
+ /* do send egress freeze steps - nothing to do */
+
+ /* do receive freeze steps */
+ rxe_freeze(dd);
+
+ /*
+ * Unfreeze the hardware - clear the freeze, wait for each
+ * block's frozen bit to clear, then clear the frozen flag.
+ */
+ write_csr(dd, CCE_CTRL, CCE_CTRL_SPC_UNFREEZE_SMASK);
+ wait_for_freeze_status(dd, 0);
+
+ if (is_a0(dd)) {
+ write_csr(dd, CCE_CTRL, CCE_CTRL_SPC_FREEZE_SMASK);
+ wait_for_freeze_status(dd, 1);
+ write_csr(dd, CCE_CTRL, CCE_CTRL_SPC_UNFREEZE_SMASK);
+ wait_for_freeze_status(dd, 0);
+ }
+
+ /* do send PIO unfreeze steps for kernel contexts */
+ pio_kernel_unfreeze(dd);
+
+ /* do send DMA unfreeze steps */
+ sdma_unfreeze(dd);
+
+ /* do send egress unfreeze steps - nothing to do */
+
+ /* do receive unfreeze steps for kernel contexts */
+ rxe_kernel_unfreeze(dd);
+
+ /*
+ * The unfreeze procedure touches global device registers when
+ * it disables and re-enables RXE. Mark the device unfrozen
+ * after all that is done so other parts of the driver waiting
+ * for the device to unfreeze don't do things out of order.
+ *
+ * The above implies that the meaning of HFI1_FROZEN flag is
+ * "Device has gone into freeze mode and freeze mode handling
+ * is still in progress."
+ *
+ * The flag will be removed when freeze mode processing has
+ * completed.
+ */
+ dd->flags &= ~HFI1_FROZEN;
+ wake_up(&dd->event_queue);
+
+ /* no longer frozen */
+ dd_dev_err(dd, "Exiting SPC freeze\n");
+}
+
+/*
+ * Handle a link up interrupt from the 8051.
+ *
+ * This is a work-queue function outside of the interrupt.
+ */
+void handle_link_up(struct work_struct *work)
+{
+ struct hfi1_pportdata *ppd = container_of(work, struct hfi1_pportdata,
+ link_up_work);
+ set_link_state(ppd, HLS_UP_INIT);
+
+ /* cache the read of DC_LCB_STS_ROUND_TRIP_LTP_CNT */
+ read_ltp_rtt(ppd->dd);
+ /*
+ * OPA specifies that certain counters are cleared on a transition
+ * to link up, so do that.
+ */
+ clear_linkup_counters(ppd->dd);
+ /*
+ * And (re)set link up default values.
+ */
+ set_linkup_defaults(ppd);
+
+ /* enforce link speed enabled */
+ if ((ppd->link_speed_active & ppd->link_speed_enabled) == 0) {
+ /* oops - current speed is not enabled, bounce */
+ dd_dev_err(ppd->dd,
+ "Link speed active 0x%x is outside enabled 0x%x, downing link\n",
+ ppd->link_speed_active, ppd->link_speed_enabled);
+ set_link_down_reason(ppd, OPA_LINKDOWN_REASON_SPEED_POLICY, 0,
+ OPA_LINKDOWN_REASON_SPEED_POLICY);
+ set_link_state(ppd, HLS_DN_OFFLINE);
+ start_link(ppd);
+ }
+}
+
+/*
+ * Handle a link down interrupt from the 8051.
+ *
+ * This is a work-queue function outside of the interrupt.
+ */
+void handle_link_down(struct work_struct *work)
+{
+ u8 lcl_reason, neigh_reason = 0;
+ struct hfi1_pportdata *ppd = container_of(work, struct hfi1_pportdata,
+ link_down_work);
+ lcl_reason = 0;
+
+ read_planned_down_reason_code(ppd->dd, &neigh_reason);
+
+ /*
+ * If no reason, assume peer-initiated but missed
+ * LinkGoingDown idle flits.
+ */
+ if (neigh_reason == 0)
+ lcl_reason = OPA_LINKDOWN_REASON_NEIGHBOR_UNKNOWN;
+
+ set_link_down_reason(ppd, lcl_reason, neigh_reason, 0);
+ set_link_state(ppd, HLS_DN_OFFLINE);
+
+ /* disable the port */
+ clear_rcvctrl(ppd->dd, RCV_CTRL_RCV_PORT_ENABLE_SMASK);
+
+ /* If there is no cable attached, turn the DC off. Otherwise,
+ * start the link bring up. */
+ if (!qsfp_mod_present(ppd))
+ dc_shutdown(ppd->dd);
+ else
+ start_link(ppd);
+}
+
+/*
+ * Mask conversion: Capability exchange to Port LTP. The capability
+ * exchange has an implicit 16b CRC that is mandatory.
+ */
+static int cap_to_port_ltp(int cap)
+{
+ int port_ltp = PORT_LTP_CRC_MODE_16; /* this mode is mandatory */
+
+ if (cap & CAP_CRC_14B)
+ port_ltp |= PORT_LTP_CRC_MODE_14;
+ if (cap & CAP_CRC_48B)
+ port_ltp |= PORT_LTP_CRC_MODE_48;
+ if (cap & CAP_CRC_12B_16B_PER_LANE)
+ port_ltp |= PORT_LTP_CRC_MODE_PER_LANE;
+
+ return port_ltp;
+}
+
+/*
+ * Convert an OPA Port LTP mask to capability mask
+ */
+int port_ltp_to_cap(int port_ltp)
+{
+ int cap_mask = 0;
+
+ if (port_ltp & PORT_LTP_CRC_MODE_14)
+ cap_mask |= CAP_CRC_14B;
+ if (port_ltp & PORT_LTP_CRC_MODE_48)
+ cap_mask |= CAP_CRC_48B;
+ if (port_ltp & PORT_LTP_CRC_MODE_PER_LANE)
+ cap_mask |= CAP_CRC_12B_16B_PER_LANE;
+
+ return cap_mask;
+}
+
+/*
+ * Convert a single DC LCB CRC mode to an OPA Port LTP mask.
+ */
+static int lcb_to_port_ltp(int lcb_crc)
+{
+ int port_ltp = 0;
+
+ if (lcb_crc == LCB_CRC_12B_16B_PER_LANE)
+ port_ltp = PORT_LTP_CRC_MODE_PER_LANE;
+ else if (lcb_crc == LCB_CRC_48B)
+ port_ltp = PORT_LTP_CRC_MODE_48;
+ else if (lcb_crc == LCB_CRC_14B)
+ port_ltp = PORT_LTP_CRC_MODE_14;
+ else
+ port_ltp = PORT_LTP_CRC_MODE_16;
+
+ return port_ltp;
+}
+
+static int neigh_is_hfi(struct hfi1_pportdata *ppd)
+{
+ return (ppd->neighbor_type & OPA_PI_MASK_NEIGH_NODE_TYPE) == 0;
+}
+
+/*
+ * Our neighbor has indicated that we are allowed to act as a fabric
+ * manager, so place the full management partition key in the second
+ * (0-based) pkey array position (see OPAv1, section 20.2.2.6.8). Note
+ * that we should already have the limited management partition key in
+ * array element 1, and also that the port is not yet up when
+ * add_full_mgmt_pkey() is invoked.
+ */
+static void add_full_mgmt_pkey(struct hfi1_pportdata *ppd)
+{
+ struct hfi1_devdata *dd = ppd->dd;
+
+ /* Sanity check - ppd->pkeys[2] should be 0 */
+ if (ppd->pkeys[2] != 0)
+ dd_dev_err(dd, "%s pkey[2] already set to 0x%x, resetting it to 0x%x\n",
+ __func__, ppd->pkeys[2], FULL_MGMT_P_KEY);
+ ppd->pkeys[2] = FULL_MGMT_P_KEY;
+ (void)hfi1_set_ib_cfg(ppd, HFI1_IB_CFG_PKEYS, 0);
+}
+
+/*
+ * Convert the given link width to the OPA link width bitmask.
+ */
+static u16 link_width_to_bits(struct hfi1_devdata *dd, u16 width)
+{
+ switch (width) {
+ case 1: return OPA_LINK_WIDTH_1X;
+ case 2: return OPA_LINK_WIDTH_2X;
+ case 3: return OPA_LINK_WIDTH_3X;
+ default:
+ /* NOTE: 0 in simulation */
+ dd_dev_info(dd, "%s: invalid width %d, using 4\n",
+ __func__, width);
+ /* fall through */
+ case 4: return OPA_LINK_WIDTH_4X;
+ }
+}
+
+/*
+ * Do a population count on the bottom nibble.
+ */
+static const u8 bit_counts[16] = {
+ 0, 1, 1, 2, 1, 2, 2, 3, 1, 2, 2, 3, 2, 3, 3, 4
+};
+static inline u8 nibble_to_count(u8 nibble)
+{
+ return bit_counts[nibble & 0xf];
+}
+
+/*
+ * Read the active lane information from the 8051 registers and return
+ * their widths.
+ *
+ * Active lane information is found in these 8051 registers:
+ * enable_lane_tx
+ * enable_lane_rx
+ */
+static void get_link_widths(struct hfi1_devdata *dd, u16 *tx_width,
+ u16 *rx_width)
+{
+ u16 tx, rx;
+ u8 enable_lane_rx;
+ u8 enable_lane_tx;
+ u8 tx_polarity_inversion;
+ u8 rx_polarity_inversion;
+ u8 max_rate;
+
+ /* read the active lanes */
+ read_tx_settings(dd, &enable_lane_tx, &tx_polarity_inversion,
+ &rx_polarity_inversion, &max_rate);
+ read_local_lni(dd, &enable_lane_rx);
+
+ /* convert to counts */
+ tx = nibble_to_count(enable_lane_tx);
+ rx = nibble_to_count(enable_lane_rx);
+
+ /*
+ * Remove the setting of link_speed_active in this routine
+ * when the 8051 firmware is using the "real" LNI and not the
+ * "engineering" LNI.
+ *
+ * Set link_speed_active here, overriding what was set in
+ * handle_verify_cap(). This is because the 8051 firmware using
+ * the "engineering" LNI does not correctly set the max_speed field.
+ * For now, to find the speed, look at max_rate after link up. This
+ * routine is called in handle_verify_cap(),after linkup, and during
+ * a downgrade. max_rate should not change after linkup so
+ * re-setting link_speed_active here should not matter.
+ */
+ if (dd->icode == ICODE_RTL_SILICON) {
+ /* max_rate: 0 = 12.5G, 1 = 25G */
+ switch (max_rate) {
+ case 0:
+ dd->pport[0].link_speed_active = OPA_LINK_SPEED_12_5G;
+ break;
+ default:
+ dd_dev_err(dd,
+ "%s: unexpected max rate %d, using 25Gb\n",
+ __func__, (int)max_rate);
+ /* fall through */
+ case 1:
+ dd->pport[0].link_speed_active = OPA_LINK_SPEED_25G;
+ break;
+ }
+ }
+
+ dd_dev_info(dd,
+ "Fabric active lanes (width): tx 0x%x (%d), rx 0x%x (%d)\n",
+ enable_lane_tx, tx, enable_lane_rx, rx);
+ *tx_width = link_width_to_bits(dd, tx);
+ *rx_width = link_width_to_bits(dd, rx);
+}
+
+/*
+ * Read verify_cap_local_fm_link_width[1] to obtain the link widths.
+ * Valid after the end of VerifyCap and during LinkUp. Does not change
+ * after link up. I.e. look elsewhere for downgrade information.
+ *
+ * Bits are:
+ * + bits [7:4] contain the number of active transmitters
+ * + bits [3:0] contain the number of active receivers
+ * These are numbers 1 through 4 and can be different values if the
+ * link is asymmetric.
+ *
+ * verify_cap_local_fm_link_width[0] retains its original value.
+ */
+static void get_linkup_widths(struct hfi1_devdata *dd, u16 *tx_width,
+ u16 *rx_width)
+{
+ u16 widths, tx, rx;
+ u8 misc_bits, local_flags;
+ u16 active_tx, active_rx;
+
+ read_vc_local_link_width(dd, &misc_bits, &local_flags, &widths);
+ tx = widths >> 12;
+ rx = (widths >> 8) & 0xf;
+ dd_dev_info(dd, "%s: active tx %d, active rx %d\n", __func__, tx, rx);
+
+ *tx_width = link_width_to_bits(dd, tx);
+ *rx_width = link_width_to_bits(dd, rx);
+
+ /* print the active widths */
+ get_link_widths(dd, &active_tx, &active_rx);
+}
+
+/*
+ * Set ppd->link_width_active and ppd->link_width_downgrade_active using
+ * hardware information when the link first comes up.
+ *
+ * The link width is not available until after VerifyCap.AllFramesReceived
+ * (the trigger for handle_verify_cap), so this is outside that routine
+ * and should be called when the 8051 signals linkup.
+ */
+void get_linkup_link_widths(struct hfi1_pportdata *ppd)
+{
+ u16 tx_width, rx_width;
+
+ /* get end-of-LNI link widths */
+ get_linkup_widths(ppd->dd, &tx_width, &rx_width);
+
+ /* use tx_width as the link is supposed to be symmetric on link up */
+ ppd->link_width_active = tx_width;
+ /* link width downgrade active (LWD.A) starts out matching LW.A */
+ ppd->link_width_downgrade_tx_active = ppd->link_width_active;
+ ppd->link_width_downgrade_rx_active = ppd->link_width_active;
+ /* per OPA spec, on link up LWD.E resets to LWD.S */
+ ppd->link_width_downgrade_enabled = ppd->link_width_downgrade_supported;
+ /* cache the active egress rate (units {10^6 bits/sec]) */
+ ppd->current_egress_rate = active_egress_rate(ppd);
+}
+
+/*
+ * Handle a verify capabilities interrupt from the 8051.
+ *
+ * This is a work-queue function outside of the interrupt.
+ */
+void handle_verify_cap(struct work_struct *work)
+{
+ struct hfi1_pportdata *ppd = container_of(work, struct hfi1_pportdata,
+ link_vc_work);
+ struct hfi1_devdata *dd = ppd->dd;
+ u64 reg;
+ u8 power_management;
+ u8 continious;
+ u8 vcu;
+ u8 vau;
+ u8 z;
+ u16 vl15buf;
+ u16 link_widths;
+ u16 crc_mask;
+ u16 crc_val;
+ u16 device_id;
+ u16 active_tx, active_rx;
+ u8 partner_supported_crc;
+ u8 remote_tx_rate;
+ u8 device_rev;
+
+ set_link_state(ppd, HLS_VERIFY_CAP);
+
+ lcb_shutdown(dd, 0);
+ adjust_lcb_for_fpga_serdes(dd);
+
+ /*
+ * These are now valid:
+ * remote VerifyCap fields in the general LNI config
+ * CSR DC8051_STS_REMOTE_GUID
+ * CSR DC8051_STS_REMOTE_NODE_TYPE
+ * CSR DC8051_STS_REMOTE_FM_SECURITY
+ */
+ read_vc_remote_phy(dd, &power_management, &continious);
+ read_vc_remote_fabric(
+ dd,
+ &vau,
+ &z,
+ &vcu,
+ &vl15buf,
+ &partner_supported_crc);
+ read_vc_remote_link_width(dd, &remote_tx_rate, &link_widths);
+ read_remote_device_id(dd, &device_id, &device_rev);
+ /*
+ * And the 'MgmtAllowed' information, which is exchanged during
+ * LNI, is also be available at this point.
+ */
+ read_mgmt_allowed(dd, &ppd->mgmt_allowed);
+ /* print the active widths */
+ get_link_widths(dd, &active_tx, &active_rx);
+ dd_dev_info(dd,
+ "Peer PHY: power management 0x%x, continuous updates 0x%x\n",
+ (int)power_management, (int)continious);
+ dd_dev_info(dd,
+ "Peer Fabric: vAU %d, Z %d, vCU %d, vl15 credits 0x%x, CRC sizes 0x%x\n",
+ (int)vau,
+ (int)z,
+ (int)vcu,
+ (int)vl15buf,
+ (int)partner_supported_crc);
+ dd_dev_info(dd, "Peer Link Width: tx rate 0x%x, widths 0x%x\n",
+ (u32)remote_tx_rate, (u32)link_widths);
+ dd_dev_info(dd, "Peer Device ID: 0x%04x, Revision 0x%02x\n",
+ (u32)device_id, (u32)device_rev);
+ /*
+ * The peer vAU value just read is the peer receiver value. HFI does
+ * not support a transmit vAU of 0 (AU == 8). We advertised that
+ * with Z=1 in the fabric capabilities sent to the peer. The peer
+ * will see our Z=1, and, if it advertised a vAU of 0, will move its
+ * receive to vAU of 1 (AU == 16). Do the same here. We do not care
+ * about the peer Z value - our sent vAU is 3 (hardwired) and is not
+ * subject to the Z value exception.
+ */
+ if (vau == 0)
+ vau = 1;
+ set_up_vl15(dd, vau, vl15buf);
+
+ /* set up the LCB CRC mode */
+ crc_mask = ppd->port_crc_mode_enabled & partner_supported_crc;
+
+ /* order is important: use the lowest bit in common */
+ if (crc_mask & CAP_CRC_14B)
+ crc_val = LCB_CRC_14B;
+ else if (crc_mask & CAP_CRC_48B)
+ crc_val = LCB_CRC_48B;
+ else if (crc_mask & CAP_CRC_12B_16B_PER_LANE)
+ crc_val = LCB_CRC_12B_16B_PER_LANE;
+ else
+ crc_val = LCB_CRC_16B;
+
+ dd_dev_info(dd, "Final LCB CRC mode: %d\n", (int)crc_val);
+ write_csr(dd, DC_LCB_CFG_CRC_MODE,
+ (u64)crc_val << DC_LCB_CFG_CRC_MODE_TX_VAL_SHIFT);
+
+ /* set (14b only) or clear sideband credit */
+ reg = read_csr(dd, SEND_CM_CTRL);
+ if (crc_val == LCB_CRC_14B && crc_14b_sideband) {
+ write_csr(dd, SEND_CM_CTRL,
+ reg | SEND_CM_CTRL_FORCE_CREDIT_MODE_SMASK);
+ } else {
+ write_csr(dd, SEND_CM_CTRL,
+ reg & ~SEND_CM_CTRL_FORCE_CREDIT_MODE_SMASK);
+ }
+
+ /* remote_tx_rate: 0 = 12.5G, 1 = 25G */
+ switch (remote_tx_rate) {
+ case 0:
+ ppd->link_speed_active = OPA_LINK_SPEED_12_5G;
+ break;
+ default:
+ dd_dev_err(dd, "%s: unexpected remote tx rate %d, using 25Gb\n",
+ __func__, (int)remote_tx_rate);
+ /* fall through */
+ case 1:
+ ppd->link_speed_active = OPA_LINK_SPEED_25G;
+ break;
+ }
+
+ /*
+ * Cache the values of the supported, enabled, and active
+ * LTP CRC modes to return in 'portinfo' queries. But the bit
+ * flags that are returned in the portinfo query differ from
+ * what's in the link_crc_mask, crc_sizes, and crc_val
+ * variables. Convert these here.
+ */
+ ppd->port_ltp_crc_mode = cap_to_port_ltp(link_crc_mask) << 8;
+ /* supported crc modes */
+ ppd->port_ltp_crc_mode |=
+ cap_to_port_ltp(ppd->port_crc_mode_enabled) << 4;
+ /* enabled crc modes */
+ ppd->port_ltp_crc_mode |= lcb_to_port_ltp(crc_val);
+ /* active crc mode */
+
+ /* set up the remote credit return table */
+ assign_remote_cm_au_table(dd, vcu);
+
+ /*
+ * The LCB is reset on entry to handle_verify_cap(), so this must
+ * be applied on every link up.
+ *
+ * Adjust LCB error kill enable to kill the link if
+ * these RBUF errors are seen:
+ * REPLAY_BUF_MBE_SMASK
+ * FLIT_INPUT_BUF_MBE_SMASK
+ */
+ if (is_a0(dd)) { /* fixed in B0 */
+ reg = read_csr(dd, DC_LCB_CFG_LINK_KILL_EN);
+ reg |= DC_LCB_CFG_LINK_KILL_EN_REPLAY_BUF_MBE_SMASK
+ | DC_LCB_CFG_LINK_KILL_EN_FLIT_INPUT_BUF_MBE_SMASK;
+ write_csr(dd, DC_LCB_CFG_LINK_KILL_EN, reg);
+ }
+
+ /* pull LCB fifos out of reset - all fifo clocks must be stable */
+ write_csr(dd, DC_LCB_CFG_TX_FIFOS_RESET, 0);
+
+ /* give 8051 access to the LCB CSRs */
+ write_csr(dd, DC_LCB_ERR_EN, 0); /* mask LCB errors */
+ set_8051_lcb_access(dd);
+
+ ppd->neighbor_guid =
+ cpu_to_be64(read_csr(dd, DC_DC8051_STS_REMOTE_GUID));
+ ppd->neighbor_type =
+ read_csr(dd, DC_DC8051_STS_REMOTE_NODE_TYPE) &
+ DC_DC8051_STS_REMOTE_NODE_TYPE_VAL_MASK;
+ ppd->neighbor_fm_security =
+ read_csr(dd, DC_DC8051_STS_REMOTE_FM_SECURITY) &
+ DC_DC8051_STS_LOCAL_FM_SECURITY_DISABLED_MASK;
+ dd_dev_info(dd, "Neighbor Guid: %llx Neighbor type %d MgmtAllowed %d FM security bypass %d\n",
+ be64_to_cpu(ppd->neighbor_guid), ppd->neighbor_type,
+ ppd->mgmt_allowed, ppd->neighbor_fm_security);
+ if (neigh_is_hfi(ppd))
+ ppd->part_enforce =
+ HFI1_PART_ENFORCE_IN | HFI1_PART_ENFORCE_OUT;
+ if (ppd->mgmt_allowed)
+ add_full_mgmt_pkey(ppd);
+
+ /* tell the 8051 to go to LinkUp */
+ set_link_state(ppd, HLS_GOING_UP);
+}
+
+/*
+ * Apply the link width downgrade enabled policy against the current active
+ * link widths.
+ *
+ * Called when the enabled policy changes or the active link widths change.
+ */
+void apply_link_downgrade_policy(struct hfi1_pportdata *ppd, int refresh_widths)
+{
+ int skip = 1;
+ int do_bounce = 0;
+ u16 lwde = ppd->link_width_downgrade_enabled;
+ u16 tx, rx;
+
+ mutex_lock(&ppd->hls_lock);
+ /* only apply if the link is up */
+ if (ppd->host_link_state & HLS_UP)
+ skip = 0;
+ mutex_unlock(&ppd->hls_lock);
+ if (skip)
+ return;
+
+ if (refresh_widths) {
+ get_link_widths(ppd->dd, &tx, &rx);
+ ppd->link_width_downgrade_tx_active = tx;
+ ppd->link_width_downgrade_rx_active = rx;
+ }
+
+ if (lwde == 0) {
+ /* downgrade is disabled */
+
+ /* bounce if not at starting active width */
+ if ((ppd->link_width_active !=
+ ppd->link_width_downgrade_tx_active)
+ || (ppd->link_width_active !=
+ ppd->link_width_downgrade_rx_active)) {
+ dd_dev_err(ppd->dd,
+ "Link downgrade is disabled and link has downgraded, downing link\n");
+ dd_dev_err(ppd->dd,
+ " original 0x%x, tx active 0x%x, rx active 0x%x\n",
+ ppd->link_width_active,
+ ppd->link_width_downgrade_tx_active,
+ ppd->link_width_downgrade_rx_active);
+ do_bounce = 1;
+ }
+ } else if ((lwde & ppd->link_width_downgrade_tx_active) == 0
+ || (lwde & ppd->link_width_downgrade_rx_active) == 0) {
+ /* Tx or Rx is outside the enabled policy */
+ dd_dev_err(ppd->dd,
+ "Link is outside of downgrade allowed, downing link\n");
+ dd_dev_err(ppd->dd,
+ " enabled 0x%x, tx active 0x%x, rx active 0x%x\n",
+ lwde,
+ ppd->link_width_downgrade_tx_active,
+ ppd->link_width_downgrade_rx_active);
+ do_bounce = 1;
+ }
+
+ if (do_bounce) {
+ set_link_down_reason(ppd, OPA_LINKDOWN_REASON_WIDTH_POLICY, 0,
+ OPA_LINKDOWN_REASON_WIDTH_POLICY);
+ set_link_state(ppd, HLS_DN_OFFLINE);
+ start_link(ppd);
+ }
+}
+
+/*
+ * Handle a link downgrade interrupt from the 8051.
+ *
+ * This is a work-queue function outside of the interrupt.
+ */
+void handle_link_downgrade(struct work_struct *work)
+{
+ struct hfi1_pportdata *ppd = container_of(work, struct hfi1_pportdata,
+ link_downgrade_work);
+
+ dd_dev_info(ppd->dd, "8051: Link width downgrade\n");
+ apply_link_downgrade_policy(ppd, 1);
+}
+
+static char *dcc_err_string(char *buf, int buf_len, u64 flags)
+{
+ return flag_string(buf, buf_len, flags, dcc_err_flags,
+ ARRAY_SIZE(dcc_err_flags));
+}
+
+static char *lcb_err_string(char *buf, int buf_len, u64 flags)
+{
+ return flag_string(buf, buf_len, flags, lcb_err_flags,
+ ARRAY_SIZE(lcb_err_flags));
+}
+
+static char *dc8051_err_string(char *buf, int buf_len, u64 flags)
+{
+ return flag_string(buf, buf_len, flags, dc8051_err_flags,
+ ARRAY_SIZE(dc8051_err_flags));
+}
+
+static char *dc8051_info_err_string(char *buf, int buf_len, u64 flags)
+{
+ return flag_string(buf, buf_len, flags, dc8051_info_err_flags,
+ ARRAY_SIZE(dc8051_info_err_flags));
+}
+
+static char *dc8051_info_host_msg_string(char *buf, int buf_len, u64 flags)
+{
+ return flag_string(buf, buf_len, flags, dc8051_info_host_msg_flags,
+ ARRAY_SIZE(dc8051_info_host_msg_flags));
+}
+
+static void handle_8051_interrupt(struct hfi1_devdata *dd, u32 unused, u64 reg)
+{
+ struct hfi1_pportdata *ppd = dd->pport;
+ u64 info, err, host_msg;
+ int queue_link_down = 0;
+ char buf[96];
+
+ /* look at the flags */
+ if (reg & DC_DC8051_ERR_FLG_SET_BY_8051_SMASK) {
+ /* 8051 information set by firmware */
+ /* read DC8051_DBG_ERR_INFO_SET_BY_8051 for details */
+ info = read_csr(dd, DC_DC8051_DBG_ERR_INFO_SET_BY_8051);
+ err = (info >> DC_DC8051_DBG_ERR_INFO_SET_BY_8051_ERROR_SHIFT)
+ & DC_DC8051_DBG_ERR_INFO_SET_BY_8051_ERROR_MASK;
+ host_msg = (info >>
+ DC_DC8051_DBG_ERR_INFO_SET_BY_8051_HOST_MSG_SHIFT)
+ & DC_DC8051_DBG_ERR_INFO_SET_BY_8051_HOST_MSG_MASK;
+
+ /*
+ * Handle error flags.
+ */
+ if (err & FAILED_LNI) {
+ /*
+ * LNI error indications are cleared by the 8051
+ * only when starting polling. Only pay attention
+ * to them when in the states that occur during
+ * LNI.
+ */
+ if (ppd->host_link_state
+ & (HLS_DN_POLL | HLS_VERIFY_CAP | HLS_GOING_UP)) {
+ queue_link_down = 1;
+ dd_dev_info(dd, "Link error: %s\n",
+ dc8051_info_err_string(buf,
+ sizeof(buf),
+ err & FAILED_LNI));
+ }
+ err &= ~(u64)FAILED_LNI;
+ }
+ if (err) {
+ /* report remaining errors, but do not do anything */
+ dd_dev_err(dd, "8051 info error: %s\n",
+ dc8051_info_err_string(buf, sizeof(buf), err));
+ }
+
+ /*
+ * Handle host message flags.
+ */
+ if (host_msg & HOST_REQ_DONE) {
+ /*
+ * Presently, the driver does a busy wait for
+ * host requests to complete. This is only an
+ * informational message.
+ * NOTE: The 8051 clears the host message
+ * information *on the next 8051 command*.
+ * Therefore, when linkup is achieved,
+ * this flag will still be set.
+ */
+ host_msg &= ~(u64)HOST_REQ_DONE;
+ }
+ if (host_msg & BC_SMA_MSG) {
+ queue_work(ppd->hfi1_wq, &ppd->sma_message_work);
+ host_msg &= ~(u64)BC_SMA_MSG;
+ }
+ if (host_msg & LINKUP_ACHIEVED) {
+ dd_dev_info(dd, "8051: Link up\n");
+ queue_work(ppd->hfi1_wq, &ppd->link_up_work);
+ host_msg &= ~(u64)LINKUP_ACHIEVED;
+ }
+ if (host_msg & EXT_DEVICE_CFG_REQ) {
+ handle_8051_request(dd);
+ host_msg &= ~(u64)EXT_DEVICE_CFG_REQ;
+ }
+ if (host_msg & VERIFY_CAP_FRAME) {
+ queue_work(ppd->hfi1_wq, &ppd->link_vc_work);
+ host_msg &= ~(u64)VERIFY_CAP_FRAME;
+ }
+ if (host_msg & LINK_GOING_DOWN) {
+ const char *extra = "";
+ /* no downgrade action needed if going down */
+ if (host_msg & LINK_WIDTH_DOWNGRADED) {
+ host_msg &= ~(u64)LINK_WIDTH_DOWNGRADED;
+ extra = " (ignoring downgrade)";
+ }
+ dd_dev_info(dd, "8051: Link down%s\n", extra);
+ queue_link_down = 1;
+ host_msg &= ~(u64)LINK_GOING_DOWN;
+ }
+ if (host_msg & LINK_WIDTH_DOWNGRADED) {
+ queue_work(ppd->hfi1_wq, &ppd->link_downgrade_work);
+ host_msg &= ~(u64)LINK_WIDTH_DOWNGRADED;
+ }
+ if (host_msg) {
+ /* report remaining messages, but do not do anything */
+ dd_dev_info(dd, "8051 info host message: %s\n",
+ dc8051_info_host_msg_string(buf, sizeof(buf),
+ host_msg));
+ }
+
+ reg &= ~DC_DC8051_ERR_FLG_SET_BY_8051_SMASK;
+ }
+ if (reg & DC_DC8051_ERR_FLG_LOST_8051_HEART_BEAT_SMASK) {
+ /*
+ * Lost the 8051 heartbeat. If this happens, we
+ * receive constant interrupts about it. Disable
+ * the interrupt after the first.
+ */
+ dd_dev_err(dd, "Lost 8051 heartbeat\n");
+ write_csr(dd, DC_DC8051_ERR_EN,
+ read_csr(dd, DC_DC8051_ERR_EN)
+ & ~DC_DC8051_ERR_EN_LOST_8051_HEART_BEAT_SMASK);
+
+ reg &= ~DC_DC8051_ERR_FLG_LOST_8051_HEART_BEAT_SMASK;
+ }
+ if (reg) {
+ /* report the error, but do not do anything */
+ dd_dev_err(dd, "8051 error: %s\n",
+ dc8051_err_string(buf, sizeof(buf), reg));
+ }
+
+ if (queue_link_down) {
+ /* if the link is already going down or disabled, do not
+ * queue another */
+ if ((ppd->host_link_state
+ & (HLS_GOING_OFFLINE|HLS_LINK_COOLDOWN))
+ || ppd->link_enabled == 0) {
+ dd_dev_info(dd, "%s: not queuing link down\n",
+ __func__);
+ } else {
+ queue_work(ppd->hfi1_wq, &ppd->link_down_work);
+ }
+ }
+}
+
+static const char * const fm_config_txt[] = {
+[0] =
+ "BadHeadDist: Distance violation between two head flits",
+[1] =
+ "BadTailDist: Distance violation between two tail flits",
+[2] =
+ "BadCtrlDist: Distance violation between two credit control flits",
+[3] =
+ "BadCrdAck: Credits return for unsupported VL",
+[4] =
+ "UnsupportedVLMarker: Received VL Marker",
+[5] =
+ "BadPreempt: Exceeded the preemption nesting level",
+[6] =
+ "BadControlFlit: Received unsupported control flit",
+/* no 7 */
+[8] =
+ "UnsupportedVLMarker: Received VL Marker for unconfigured or disabled VL",
+};
+
+static const char * const port_rcv_txt[] = {
+[1] =
+ "BadPktLen: Illegal PktLen",
+[2] =
+ "PktLenTooLong: Packet longer than PktLen",
+[3] =
+ "PktLenTooShort: Packet shorter than PktLen",
+[4] =
+ "BadSLID: Illegal SLID (0, using multicast as SLID, does not include security validation of SLID)",
+[5] =
+ "BadDLID: Illegal DLID (0, doesn't match HFI)",
+[6] =
+ "BadL2: Illegal L2 opcode",
+[7] =
+ "BadSC: Unsupported SC",
+[9] =
+ "BadRC: Illegal RC",
+[11] =
+ "PreemptError: Preempting with same VL",
+[12] =
+ "PreemptVL15: Preempting a VL15 packet",
+[13] =
+ "BadVLMarker: VL Marker for an unpreempted VL",
+};
+
+#define OPA_LDR_FMCONFIG_OFFSET 16
+#define OPA_LDR_PORTRCV_OFFSET 0
+static void handle_dcc_err(struct hfi1_devdata *dd, u32 unused, u64 reg)
+{
+ u64 info, hdr0, hdr1;
+ const char *extra;
+ char buf[96];
+ struct hfi1_pportdata *ppd = dd->pport;
+ u8 lcl_reason = 0;
+ int do_bounce = 0;
+
+ if (reg & DCC_ERR_FLG_UNCORRECTABLE_ERR_SMASK) {
+ if (!(dd->err_info_uncorrectable & OPA_EI_STATUS_SMASK)) {
+ info = read_csr(dd, DCC_ERR_INFO_UNCORRECTABLE);
+ dd->err_info_uncorrectable = info & OPA_EI_CODE_SMASK;
+ /* set status bit */
+ dd->err_info_uncorrectable |= OPA_EI_STATUS_SMASK;
+ }
+ reg &= ~DCC_ERR_FLG_UNCORRECTABLE_ERR_SMASK;
+ }
+
+ if (reg & DCC_ERR_FLG_LINK_ERR_SMASK) {
+ struct hfi1_pportdata *ppd = dd->pport;
+ /* this counter saturates at (2^32) - 1 */
+ if (ppd->link_downed < (u32)UINT_MAX)
+ ppd->link_downed++;
+ reg &= ~DCC_ERR_FLG_LINK_ERR_SMASK;
+ }
+
+ if (reg & DCC_ERR_FLG_FMCONFIG_ERR_SMASK) {
+ u8 reason_valid = 1;
+
+ info = read_csr(dd, DCC_ERR_INFO_FMCONFIG);
+ if (!(dd->err_info_fmconfig & OPA_EI_STATUS_SMASK)) {
+ dd->err_info_fmconfig = info & OPA_EI_CODE_SMASK;
+ /* set status bit */
+ dd->err_info_fmconfig |= OPA_EI_STATUS_SMASK;
+ }
+ switch (info) {
+ case 0:
+ case 1:
+ case 2:
+ case 3:
+ case 4:
+ case 5:
+ case 6:
+ extra = fm_config_txt[info];
+ break;
+ case 8:
+ extra = fm_config_txt[info];
+ if (!do_bounce && ppd->port_error_action &
+ OPA_PI_MASK_FM_CFG_UNSUPPORTED_VL_MARKER) {
+ do_bounce = 1;
+ /*
+ * lcl_reason cannot be derived from info
+ * for this error
+ */
+ lcl_reason =
+ OPA_LINKDOWN_REASON_UNSUPPORTED_VL_MARKER;
+ }
+ break;
+ default:
+ reason_valid = 0;
+ snprintf(buf, sizeof(buf), "reserved%lld", info);
+ extra = buf;
+ break;
+ }
+
+ if (reason_valid && !do_bounce) {
+ do_bounce = ppd->port_error_action &
+ (1 << (OPA_LDR_FMCONFIG_OFFSET + info));
+ lcl_reason = (lcl_reason ? lcl_reason :
+ info + OPA_LINKDOWN_REASON_BAD_HEAD_DIST);
+ }
+
+ /* just report this */
+ dd_dev_info(dd, "DCC Error: fmconfig error: %s\n", extra);
+ reg &= ~DCC_ERR_FLG_FMCONFIG_ERR_SMASK;
+ }
+
+ if (reg & DCC_ERR_FLG_RCVPORT_ERR_SMASK) {
+ u8 reason_valid = 1;
+
+ info = read_csr(dd, DCC_ERR_INFO_PORTRCV);
+ hdr0 = read_csr(dd, DCC_ERR_INFO_PORTRCV_HDR0);
+ hdr1 = read_csr(dd, DCC_ERR_INFO_PORTRCV_HDR1);
+ if (!(dd->err_info_rcvport.status_and_code &
+ OPA_EI_STATUS_SMASK)) {
+ dd->err_info_rcvport.status_and_code =
+ info & OPA_EI_CODE_SMASK;
+ /* set status bit */
+ dd->err_info_rcvport.status_and_code |=
+ OPA_EI_STATUS_SMASK;
+ /* save first 2 flits in the packet that caused
+ * the error */
+ dd->err_info_rcvport.packet_flit1 = hdr0;
+ dd->err_info_rcvport.packet_flit2 = hdr1;
+ }
+ switch (info & 0xf) {
+ case 1:
+ case 2:
+ case 3:
+ case 4:
+ case 5:
+ case 6:
+ case 7:
+ case 9:
+ case 11:
+ case 12:
+ case 13:
+ extra = port_rcv_txt[info & 0xf];
+ break;
+ default:
+ reason_valid = 0;
+ snprintf(buf, sizeof(buf), "reserved%lld", info);
+ extra = buf;
+ break;
+ }
+
+ if (reason_valid && !do_bounce) {
+ do_bounce = ppd->port_error_action &
+ (1 << ((info & 0xf) + OPA_LDR_PORTRCV_OFFSET));
+ lcl_reason =
+ (info & 0xf) + OPA_LINKDOWN_REASON_RCV_ERROR_0;
+ }
+
+ /* just report this */
+ dd_dev_info(dd, "DCC Error: PortRcv error: %s\n", extra);
+ dd_dev_info(dd, " hdr0 0x%llx, hdr1 0x%llx\n",
+ hdr0, hdr1);
+
+ reg &= ~DCC_ERR_FLG_RCVPORT_ERR_SMASK;
+ }
+
+ if (reg & DCC_ERR_FLG_EN_CSR_ACCESS_BLOCKED_UC_SMASK) {
+ /* informative only */
+ dd_dev_info(dd, "8051 access to LCB blocked\n");
+ reg &= ~DCC_ERR_FLG_EN_CSR_ACCESS_BLOCKED_UC_SMASK;
+ }
+ if (reg & DCC_ERR_FLG_EN_CSR_ACCESS_BLOCKED_HOST_SMASK) {
+ /* informative only */
+ dd_dev_info(dd, "host access to LCB blocked\n");
+ reg &= ~DCC_ERR_FLG_EN_CSR_ACCESS_BLOCKED_HOST_SMASK;
+ }
+
+ /* report any remaining errors */
+ if (reg)
+ dd_dev_info(dd, "DCC Error: %s\n",
+ dcc_err_string(buf, sizeof(buf), reg));
+
+ if (lcl_reason == 0)
+ lcl_reason = OPA_LINKDOWN_REASON_UNKNOWN;
+
+ if (do_bounce) {
+ dd_dev_info(dd, "%s: PortErrorAction bounce\n", __func__);
+ set_link_down_reason(ppd, lcl_reason, 0, lcl_reason);
+ start_link(ppd);
+ }
+}
+
+static void handle_lcb_err(struct hfi1_devdata *dd, u32 unused, u64 reg)
+{
+ char buf[96];
+
+ dd_dev_info(dd, "LCB Error: %s\n",
+ lcb_err_string(buf, sizeof(buf), reg));
+}
+
+/*
+ * CCE block DC interrupt. Source is < 8.
+ */
+static void is_dc_int(struct hfi1_devdata *dd, unsigned int source)
+{
+ const struct err_reg_info *eri = &dc_errs[source];
+
+ if (eri->handler) {
+ interrupt_clear_down(dd, 0, eri);
+ } else if (source == 3 /* dc_lbm_int */) {
+ /*
+ * This indicates that a parity error has occurred on the
+ * address/control lines presented to the LBM. The error
+ * is a single pulse, there is no associated error flag,
+ * and it is non-maskable. This is because if a parity
+ * error occurs on the request the request is dropped.
+ * This should never occur, but it is nice to know if it
+ * ever does.
+ */
+ dd_dev_err(dd, "Parity error in DC LBM block\n");
+ } else {
+ dd_dev_err(dd, "Invalid DC interrupt %u\n", source);
+ }
+}
+
+/*
+ * TX block send credit interrupt. Source is < 160.
+ */
+static void is_send_credit_int(struct hfi1_devdata *dd, unsigned int source)
+{
+ sc_group_release_update(dd, source);
+}
+
+/*
+ * TX block SDMA interrupt. Source is < 48.
+ *
+ * SDMA interrupts are grouped by type:
+ *
+ * 0 - N-1 = SDma
+ * N - 2N-1 = SDmaProgress
+ * 2N - 3N-1 = SDmaIdle
+ */
+static void is_sdma_eng_int(struct hfi1_devdata *dd, unsigned int source)
+{
+ /* what interrupt */
+ unsigned int what = source / TXE_NUM_SDMA_ENGINES;
+ /* which engine */
+ unsigned int which = source % TXE_NUM_SDMA_ENGINES;
+
+#ifdef CONFIG_SDMA_VERBOSITY
+ dd_dev_err(dd, "CONFIG SDMA(%u) %s:%d %s()\n", which,
+ slashstrip(__FILE__), __LINE__, __func__);
+ sdma_dumpstate(&dd->per_sdma[which]);
+#endif
+
+ if (likely(what < 3 && which < dd->num_sdma)) {
+ sdma_engine_interrupt(&dd->per_sdma[which], 1ull << source);
+ } else {
+ /* should not happen */
+ dd_dev_err(dd, "Invalid SDMA interrupt 0x%x\n", source);
+ }
+}
+
+/*
+ * RX block receive available interrupt. Source is < 160.
+ */
+static void is_rcv_avail_int(struct hfi1_devdata *dd, unsigned int source)
+{
+ struct hfi1_ctxtdata *rcd;
+ char *err_detail;
+
+ if (likely(source < dd->num_rcv_contexts)) {
+ rcd = dd->rcd[source];
+ if (rcd) {
+ if (source < dd->first_user_ctxt)
+ rcd->do_interrupt(rcd);
+ else
+ handle_user_interrupt(rcd);
+ return; /* OK */
+ }
+ /* received an interrupt, but no rcd */
+ err_detail = "dataless";
+ } else {
+ /* received an interrupt, but are not using that context */
+ err_detail = "out of range";
+ }
+ dd_dev_err(dd, "unexpected %s receive available context interrupt %u\n",
+ err_detail, source);
+}
+
+/*
+ * RX block receive urgent interrupt. Source is < 160.
+ */
+static void is_rcv_urgent_int(struct hfi1_devdata *dd, unsigned int source)
+{
+ struct hfi1_ctxtdata *rcd;
+ char *err_detail;
+
+ if (likely(source < dd->num_rcv_contexts)) {
+ rcd = dd->rcd[source];
+ if (rcd) {
+ /* only pay attention to user urgent interrupts */
+ if (source >= dd->first_user_ctxt)
+ handle_user_interrupt(rcd);
+ return; /* OK */
+ }
+ /* received an interrupt, but no rcd */
+ err_detail = "dataless";
+ } else {
+ /* received an interrupt, but are not using that context */
+ err_detail = "out of range";
+ }
+ dd_dev_err(dd, "unexpected %s receive urgent context interrupt %u\n",
+ err_detail, source);
+}
+
+/*
+ * Reserved range interrupt. Should not be called in normal operation.
+ */
+static void is_reserved_int(struct hfi1_devdata *dd, unsigned int source)
+{
+ char name[64];
+
+ dd_dev_err(dd, "unexpected %s interrupt\n",
+ is_reserved_name(name, sizeof(name), source));
+}
+
+static const struct is_table is_table[] = {
+/* start end
+ name func interrupt func */
+{ IS_GENERAL_ERR_START, IS_GENERAL_ERR_END,
+ is_misc_err_name, is_misc_err_int },
+{ IS_SDMAENG_ERR_START, IS_SDMAENG_ERR_END,
+ is_sdma_eng_err_name, is_sdma_eng_err_int },
+{ IS_SENDCTXT_ERR_START, IS_SENDCTXT_ERR_END,
+ is_sendctxt_err_name, is_sendctxt_err_int },
+{ IS_SDMA_START, IS_SDMA_END,
+ is_sdma_eng_name, is_sdma_eng_int },
+{ IS_VARIOUS_START, IS_VARIOUS_END,
+ is_various_name, is_various_int },
+{ IS_DC_START, IS_DC_END,
+ is_dc_name, is_dc_int },
+{ IS_RCVAVAIL_START, IS_RCVAVAIL_END,
+ is_rcv_avail_name, is_rcv_avail_int },
+{ IS_RCVURGENT_START, IS_RCVURGENT_END,
+ is_rcv_urgent_name, is_rcv_urgent_int },
+{ IS_SENDCREDIT_START, IS_SENDCREDIT_END,
+ is_send_credit_name, is_send_credit_int},
+{ IS_RESERVED_START, IS_RESERVED_END,
+ is_reserved_name, is_reserved_int},
+};
+
+/*
+ * Interrupt source interrupt - called when the given source has an interrupt.
+ * Source is a bit index into an array of 64-bit integers.
+ */
+static void is_interrupt(struct hfi1_devdata *dd, unsigned int source)
+{
+ const struct is_table *entry;
+
+ /* avoids a double compare by walking the table in-order */
+ for (entry = &is_table[0]; entry->is_name; entry++) {
+ if (source < entry->end) {
+ trace_hfi1_interrupt(dd, entry, source);
+ entry->is_int(dd, source - entry->start);
+ return;
+ }
+ }
+ /* fell off the end */
+ dd_dev_err(dd, "invalid interrupt source %u\n", source);
+}
+
+/*
+ * General interrupt handler. This is able to correctly handle
+ * all interrupts in case INTx is used.
+ */
+static irqreturn_t general_interrupt(int irq, void *data)
+{
+ struct hfi1_devdata *dd = data;
+ u64 regs[CCE_NUM_INT_CSRS];
+ u32 bit;
+ int i;
+
+ this_cpu_inc(*dd->int_counter);
+
+ /* phase 1: scan and clear all handled interrupts */
+ for (i = 0; i < CCE_NUM_INT_CSRS; i++) {
+ if (dd->gi_mask[i] == 0) {
+ regs[i] = 0; /* used later */
+ continue;
+ }
+ regs[i] = read_csr(dd, CCE_INT_STATUS + (8 * i)) &
+ dd->gi_mask[i];
+ /* only clear if anything is set */
+ if (regs[i])
+ write_csr(dd, CCE_INT_CLEAR + (8 * i), regs[i]);
+ }
+
+ /* phase 2: call the appropriate handler */
+ for_each_set_bit(bit, (unsigned long *)®s[0],
+ CCE_NUM_INT_CSRS*64) {
+ is_interrupt(dd, bit);
+ }
+
+ return IRQ_HANDLED;
+}
+
+static irqreturn_t sdma_interrupt(int irq, void *data)
+{
+ struct sdma_engine *sde = data;
+ struct hfi1_devdata *dd = sde->dd;
+ u64 status;
+
+#ifdef CONFIG_SDMA_VERBOSITY
+ dd_dev_err(dd, "CONFIG SDMA(%u) %s:%d %s()\n", sde->this_idx,
+ slashstrip(__FILE__), __LINE__, __func__);
+ sdma_dumpstate(sde);
+#endif
+
+ this_cpu_inc(*dd->int_counter);
+
+ /* This read_csr is really bad in the hot path */
+ status = read_csr(dd,
+ CCE_INT_STATUS + (8*(IS_SDMA_START/64)))
+ & sde->imask;
+ if (likely(status)) {
+ /* clear the interrupt(s) */
+ write_csr(dd,
+ CCE_INT_CLEAR + (8*(IS_SDMA_START/64)),
+ status);
+
+ /* handle the interrupt(s) */
+ sdma_engine_interrupt(sde, status);
+ } else
+ dd_dev_err(dd, "SDMA engine %u interrupt, but no status bits set\n",
+ sde->this_idx);
+
+ return IRQ_HANDLED;
+}
+
+/*
+ * NOTE: this routine expects to be on its own MSI-X interrupt. If
+ * multiple receive contexts share the same MSI-X interrupt, then this
+ * routine must check for who received it.
+ */
+static irqreturn_t receive_context_interrupt(int irq, void *data)
+{
+ struct hfi1_ctxtdata *rcd = data;
+ struct hfi1_devdata *dd = rcd->dd;
+
+ trace_hfi1_receive_interrupt(dd, rcd->ctxt);
+ this_cpu_inc(*dd->int_counter);
+
+ /* clear the interrupt */
+ write_csr(rcd->dd, CCE_INT_CLEAR + (8*rcd->ireg), rcd->imask);
+
+ /* handle the interrupt */
+ rcd->do_interrupt(rcd);
+
+ return IRQ_HANDLED;
+}
+
+/* ========================================================================= */
+
+static u32 read_physical_state(struct hfi1_devdata *dd)
+{
+ u64 reg;
+
+ reg = read_csr(dd, DC_DC8051_STS_CUR_STATE);
+ return (reg >> DC_DC8051_STS_CUR_STATE_PORT_SHIFT)
+ & DC_DC8051_STS_CUR_STATE_PORT_MASK;
+}
+
+static u32 read_logical_state(struct hfi1_devdata *dd)
+{
+ u64 reg;
+
+ reg = read_csr(dd, DCC_CFG_PORT_CONFIG);
+ return (reg >> DCC_CFG_PORT_CONFIG_LINK_STATE_SHIFT)
+ & DCC_CFG_PORT_CONFIG_LINK_STATE_MASK;
+}
+
+static void set_logical_state(struct hfi1_devdata *dd, u32 chip_lstate)
+{
+ u64 reg;
+
+ reg = read_csr(dd, DCC_CFG_PORT_CONFIG);
+ /* clear current state, set new state */
+ reg &= ~DCC_CFG_PORT_CONFIG_LINK_STATE_SMASK;
+ reg |= (u64)chip_lstate << DCC_CFG_PORT_CONFIG_LINK_STATE_SHIFT;
+ write_csr(dd, DCC_CFG_PORT_CONFIG, reg);
+}
+
+/*
+ * Use the 8051 to read a LCB CSR.
+ */
+static int read_lcb_via_8051(struct hfi1_devdata *dd, u32 addr, u64 *data)
+{
+ u32 regno;
+ int ret;
+
+ if (dd->icode == ICODE_FUNCTIONAL_SIMULATOR) {
+ if (acquire_lcb_access(dd, 0) == 0) {
+ *data = read_csr(dd, addr);
+ release_lcb_access(dd, 0);
+ return 0;
+ }
+ return -EBUSY;
+ }
+
+ /* register is an index of LCB registers: (offset - base) / 8 */
+ regno = (addr - DC_LCB_CFG_RUN) >> 3;
+ ret = do_8051_command(dd, HCMD_READ_LCB_CSR, regno, data);
+ if (ret != HCMD_SUCCESS)
+ return -EBUSY;
+ return 0;
+}
+
+/*
+ * Read an LCB CSR. Access may not be in host control, so check.
+ * Return 0 on success, -EBUSY on failure.
+ */
+int read_lcb_csr(struct hfi1_devdata *dd, u32 addr, u64 *data)
+{
+ struct hfi1_pportdata *ppd = dd->pport;
+
+ /* if up, go through the 8051 for the value */
+ if (ppd->host_link_state & HLS_UP)
+ return read_lcb_via_8051(dd, addr, data);
+ /* if going up or down, no access */
+ if (ppd->host_link_state & (HLS_GOING_UP | HLS_GOING_OFFLINE))
+ return -EBUSY;
+ /* otherwise, host has access */
+ *data = read_csr(dd, addr);
+ return 0;
+}
+
+/*
+ * Use the 8051 to write a LCB CSR.
+ */
+static int write_lcb_via_8051(struct hfi1_devdata *dd, u32 addr, u64 data)
+{
+
+ if (acquire_lcb_access(dd, 0) == 0) {
+ write_csr(dd, addr, data);
+ release_lcb_access(dd, 0);
+ return 0;
+ }
+ return -EBUSY;
+}
+
+/*
+ * Write an LCB CSR. Access may not be in host control, so check.
+ * Return 0 on success, -EBUSY on failure.
+ */
+int write_lcb_csr(struct hfi1_devdata *dd, u32 addr, u64 data)
+{
+ struct hfi1_pportdata *ppd = dd->pport;
+
+ /* if up, go through the 8051 for the value */
+ if (ppd->host_link_state & HLS_UP)
+ return write_lcb_via_8051(dd, addr, data);
+ /* if going up or down, no access */
+ if (ppd->host_link_state & (HLS_GOING_UP | HLS_GOING_OFFLINE))
+ return -EBUSY;
+ /* otherwise, host has access */
+ write_csr(dd, addr, data);
+ return 0;
+}
+
+/*
+ * Returns:
+ * < 0 = Linux error, not able to get access
+ * > 0 = 8051 command RETURN_CODE
+ */
+static int do_8051_command(
+ struct hfi1_devdata *dd,
+ u32 type,
+ u64 in_data,
+ u64 *out_data)
+{
+ u64 reg, completed;
+ int return_code;
+ unsigned long flags;
+ unsigned long timeout;
+
+ hfi1_cdbg(DC8051, "type %d, data 0x%012llx", type, in_data);
+
+ /*
+ * Alternative to holding the lock for a long time:
+ * - keep busy wait - have other users bounce off
+ */
+ spin_lock_irqsave(&dd->dc8051_lock, flags);
+
+
+ /* We can't send any commands to the 8051 if it's in reset */
+ if (dd->dc_shutdown) {
+ return_code = -ENODEV;
+ goto fail;
+ }
+
+ /*
+ * If an 8051 host command timed out previously, then the 8051 is
+ * stuck.
+ *
+ * On first timeout, attempt to reset and restart the entire DC
+ * block (including 8051). (Is this too big of a hammer?)
+ *
+ * If the 8051 times out a second time, the reset did not bring it
+ * back to healthy life. In that case, fail any subsequent commands.
+ */
+ if (dd->dc8051_timed_out) {
+ if (dd->dc8051_timed_out > 1) {
+ dd_dev_err(dd,
+ "Previous 8051 host command timed out, skipping command %u\n",
+ type);
+ return_code = -ENXIO;
+ goto fail;
+ }
+ spin_unlock_irqrestore(&dd->dc8051_lock, flags);
+ dc_shutdown(dd);
+ dc_start(dd);
+ spin_lock_irqsave(&dd->dc8051_lock, flags);
+ }
+
+ /*
+ * If there is no timeout, then the 8051 command interface is
+ * waiting for a command.
+ */
+
+ /*
+ * Do two writes: the first to stabilize the type and req_data, the
+ * second to activate.
+ */
+ reg = ((u64)type & DC_DC8051_CFG_HOST_CMD_0_REQ_TYPE_MASK)
+ << DC_DC8051_CFG_HOST_CMD_0_REQ_TYPE_SHIFT
+ | (in_data & DC_DC8051_CFG_HOST_CMD_0_REQ_DATA_MASK)
+ << DC_DC8051_CFG_HOST_CMD_0_REQ_DATA_SHIFT;
+ write_csr(dd, DC_DC8051_CFG_HOST_CMD_0, reg);
+ reg |= DC_DC8051_CFG_HOST_CMD_0_REQ_NEW_SMASK;
+ write_csr(dd, DC_DC8051_CFG_HOST_CMD_0, reg);
+
+ /* wait for completion, alternate: interrupt */
+ timeout = jiffies + msecs_to_jiffies(
+ quick_linkup ? 20000 : DC8051_COMMAND_TIMEOUT);
+ while (1) {
+ reg = read_csr(dd, DC_DC8051_CFG_HOST_CMD_1);
+ completed = reg & DC_DC8051_CFG_HOST_CMD_1_COMPLETED_SMASK;
+ if (completed)
+ break;
+ if (time_after(jiffies, timeout)) {
+ dd->dc8051_timed_out++;
+ dd_dev_err(dd, "8051 host command %u timeout\n", type);
+ if (out_data)
+ *out_data = 0;
+ return_code = -ETIMEDOUT;
+ goto fail;
+ }
+ udelay(2);
+ }
+
+ if (out_data) {
+ *out_data = (reg >> DC_DC8051_CFG_HOST_CMD_1_RSP_DATA_SHIFT)
+ & DC_DC8051_CFG_HOST_CMD_1_RSP_DATA_MASK;
+ if (type == HCMD_READ_LCB_CSR) {
+ /* top 16 bits are in a different register */
+ *out_data |= (read_csr(dd, DC_DC8051_CFG_EXT_DEV_1)
+ & DC_DC8051_CFG_EXT_DEV_1_REQ_DATA_SMASK)
+ << (48
+ - DC_DC8051_CFG_EXT_DEV_1_REQ_DATA_SHIFT);
+ }
+ }
+ return_code = (reg >> DC_DC8051_CFG_HOST_CMD_1_RETURN_CODE_SHIFT)
+ & DC_DC8051_CFG_HOST_CMD_1_RETURN_CODE_MASK;
+ dd->dc8051_timed_out = 0;
+ /*
+ * Clear command for next user.
+ */
+ write_csr(dd, DC_DC8051_CFG_HOST_CMD_0, 0);
+
+fail:
+ spin_unlock_irqrestore(&dd->dc8051_lock, flags);
+
+ return return_code;
+}
+
+static int set_physical_link_state(struct hfi1_devdata *dd, u64 state)
+{
+ return do_8051_command(dd, HCMD_CHANGE_PHY_STATE, state, NULL);
+}
+
+static int load_8051_config(struct hfi1_devdata *dd, u8 field_id,
+ u8 lane_id, u32 config_data)
+{
+ u64 data;
+ int ret;
+
+ data = (u64)field_id << LOAD_DATA_FIELD_ID_SHIFT
+ | (u64)lane_id << LOAD_DATA_LANE_ID_SHIFT
+ | (u64)config_data << LOAD_DATA_DATA_SHIFT;
+ ret = do_8051_command(dd, HCMD_LOAD_CONFIG_DATA, data, NULL);
+ if (ret != HCMD_SUCCESS) {
+ dd_dev_err(dd,
+ "load 8051 config: field id %d, lane %d, err %d\n",
+ (int)field_id, (int)lane_id, ret);
+ }
+ return ret;
+}
+
+static int read_8051_config(struct hfi1_devdata *dd, u8 field_id,
+ u8 lane_id, u32 *config_data)
+{
+ u64 in_data;
+ u64 out_data;
+ int ret;
+
+ in_data = (u64)field_id << READ_DATA_FIELD_ID_SHIFT
+ | (u64)lane_id << READ_DATA_LANE_ID_SHIFT;
+ ret = do_8051_command(dd, HCMD_READ_CONFIG_DATA, in_data,
+ &out_data);
+ if (ret != HCMD_SUCCESS) {
+ dd_dev_err(dd,
+ "read 8051 config: field id %d, lane %d, err %d failed\n",
+ (int)field_id, (int)lane_id, ret);
+ out_data = 0;
+ }
+ *config_data = (out_data >> READ_DATA_DATA_SHIFT) & READ_DATA_DATA_MASK;
+ return ret;
+}
+
+static int write_vc_local_phy(struct hfi1_devdata *dd, u8 power_management,
+ u8 continuous)
+{
+ u32 frame;
+
+ frame = continuous << CONTINIOUS_REMOTE_UPDATE_SUPPORT_SHIFT
+ | power_management << POWER_MANAGEMENT_SHIFT;
+ return load_8051_config(dd, VERIFY_CAP_LOCAL_PHY,
+ GENERAL_CONFIG, frame);
+}
+
+static int write_vc_local_fabric(struct hfi1_devdata *dd, u8 vau, u8 z, u8 vcu,
+ u16 vl15buf, u8 crc_sizes)
+{
+ u32 frame;
+
+ frame = (u32)vau << VAU_SHIFT
+ | (u32)z << Z_SHIFT
+ | (u32)vcu << VCU_SHIFT
+ | (u32)vl15buf << VL15BUF_SHIFT
+ | (u32)crc_sizes << CRC_SIZES_SHIFT;
+ return load_8051_config(dd, VERIFY_CAP_LOCAL_FABRIC,
+ GENERAL_CONFIG, frame);
+}
+
+static void read_vc_local_link_width(struct hfi1_devdata *dd, u8 *misc_bits,
+ u8 *flag_bits, u16 *link_widths)
+{
+ u32 frame;
+
+ read_8051_config(dd, VERIFY_CAP_LOCAL_LINK_WIDTH, GENERAL_CONFIG,
+ &frame);
+ *misc_bits = (frame >> MISC_CONFIG_BITS_SHIFT) & MISC_CONFIG_BITS_MASK;
+ *flag_bits = (frame >> LOCAL_FLAG_BITS_SHIFT) & LOCAL_FLAG_BITS_MASK;
+ *link_widths = (frame >> LINK_WIDTH_SHIFT) & LINK_WIDTH_MASK;
+}
+
+static int write_vc_local_link_width(struct hfi1_devdata *dd,
+ u8 misc_bits,
+ u8 flag_bits,
+ u16 link_widths)
+{
+ u32 frame;
+
+ frame = (u32)misc_bits << MISC_CONFIG_BITS_SHIFT
+ | (u32)flag_bits << LOCAL_FLAG_BITS_SHIFT
+ | (u32)link_widths << LINK_WIDTH_SHIFT;
+ return load_8051_config(dd, VERIFY_CAP_LOCAL_LINK_WIDTH, GENERAL_CONFIG,
+ frame);
+}
+
+static int write_local_device_id(struct hfi1_devdata *dd, u16 device_id,
+ u8 device_rev)
+{
+ u32 frame;
+
+ frame = ((u32)device_id << LOCAL_DEVICE_ID_SHIFT)
+ | ((u32)device_rev << LOCAL_DEVICE_REV_SHIFT);
+ return load_8051_config(dd, LOCAL_DEVICE_ID, GENERAL_CONFIG, frame);
+}
+
+static void read_remote_device_id(struct hfi1_devdata *dd, u16 *device_id,
+ u8 *device_rev)
+{
+ u32 frame;
+
+ read_8051_config(dd, REMOTE_DEVICE_ID, GENERAL_CONFIG, &frame);
+ *device_id = (frame >> REMOTE_DEVICE_ID_SHIFT) & REMOTE_DEVICE_ID_MASK;
+ *device_rev = (frame >> REMOTE_DEVICE_REV_SHIFT)
+ & REMOTE_DEVICE_REV_MASK;
+}
+
+void read_misc_status(struct hfi1_devdata *dd, u8 *ver_a, u8 *ver_b)
+{
+ u32 frame;
+
+ read_8051_config(dd, MISC_STATUS, GENERAL_CONFIG, &frame);
+ *ver_a = (frame >> STS_FM_VERSION_A_SHIFT) & STS_FM_VERSION_A_MASK;
+ *ver_b = (frame >> STS_FM_VERSION_B_SHIFT) & STS_FM_VERSION_B_MASK;
+}
+
+static void read_vc_remote_phy(struct hfi1_devdata *dd, u8 *power_management,
+ u8 *continuous)
+{
+ u32 frame;
+
+ read_8051_config(dd, VERIFY_CAP_REMOTE_PHY, GENERAL_CONFIG, &frame);
+ *power_management = (frame >> POWER_MANAGEMENT_SHIFT)
+ & POWER_MANAGEMENT_MASK;
+ *continuous = (frame >> CONTINIOUS_REMOTE_UPDATE_SUPPORT_SHIFT)
+ & CONTINIOUS_REMOTE_UPDATE_SUPPORT_MASK;
+}
+
+static void read_vc_remote_fabric(struct hfi1_devdata *dd, u8 *vau, u8 *z,
+ u8 *vcu, u16 *vl15buf, u8 *crc_sizes)
+{
+ u32 frame;
+
+ read_8051_config(dd, VERIFY_CAP_REMOTE_FABRIC, GENERAL_CONFIG, &frame);
+ *vau = (frame >> VAU_SHIFT) & VAU_MASK;
+ *z = (frame >> Z_SHIFT) & Z_MASK;
+ *vcu = (frame >> VCU_SHIFT) & VCU_MASK;
+ *vl15buf = (frame >> VL15BUF_SHIFT) & VL15BUF_MASK;
+ *crc_sizes = (frame >> CRC_SIZES_SHIFT) & CRC_SIZES_MASK;
+}
+
+static void read_vc_remote_link_width(struct hfi1_devdata *dd,
+ u8 *remote_tx_rate,
+ u16 *link_widths)
+{
+ u32 frame;
+
+ read_8051_config(dd, VERIFY_CAP_REMOTE_LINK_WIDTH, GENERAL_CONFIG,
+ &frame);
+ *remote_tx_rate = (frame >> REMOTE_TX_RATE_SHIFT)
+ & REMOTE_TX_RATE_MASK;
+ *link_widths = (frame >> LINK_WIDTH_SHIFT) & LINK_WIDTH_MASK;
+}
+
+static void read_local_lni(struct hfi1_devdata *dd, u8 *enable_lane_rx)
+{
+ u32 frame;
+
+ read_8051_config(dd, LOCAL_LNI_INFO, GENERAL_CONFIG, &frame);
+ *enable_lane_rx = (frame >> ENABLE_LANE_RX_SHIFT) & ENABLE_LANE_RX_MASK;
+}
+
+static void read_mgmt_allowed(struct hfi1_devdata *dd, u8 *mgmt_allowed)
+{
+ u32 frame;
+
+ read_8051_config(dd, REMOTE_LNI_INFO, GENERAL_CONFIG, &frame);
+ *mgmt_allowed = (frame >> MGMT_ALLOWED_SHIFT) & MGMT_ALLOWED_MASK;
+}
+
+static void read_last_local_state(struct hfi1_devdata *dd, u32 *lls)
+{
+ read_8051_config(dd, LAST_LOCAL_STATE_COMPLETE, GENERAL_CONFIG, lls);
+}
+
+static void read_last_remote_state(struct hfi1_devdata *dd, u32 *lrs)
+{
+ read_8051_config(dd, LAST_REMOTE_STATE_COMPLETE, GENERAL_CONFIG, lrs);
+}
+
+void hfi1_read_link_quality(struct hfi1_devdata *dd, u8 *link_quality)
+{
+ u32 frame;
+
+ read_8051_config(dd, LINK_QUALITY_INFO, GENERAL_CONFIG, &frame);
+ *link_quality = (frame >> LINK_QUALITY_SHIFT) & LINK_QUALITY_MASK;
+}
+
+static void read_planned_down_reason_code(struct hfi1_devdata *dd, u8 *pdrrc)
+{
+ u32 frame;
+
+ read_8051_config(dd, LINK_QUALITY_INFO, GENERAL_CONFIG, &frame);
+ *pdrrc = (frame >> DOWN_REMOTE_REASON_SHIFT) & DOWN_REMOTE_REASON_MASK;
+}
+
+static int read_tx_settings(struct hfi1_devdata *dd,
+ u8 *enable_lane_tx,
+ u8 *tx_polarity_inversion,
+ u8 *rx_polarity_inversion,
+ u8 *max_rate)
+{
+ u32 frame;
+ int ret;
+
+ ret = read_8051_config(dd, TX_SETTINGS, GENERAL_CONFIG, &frame);
+ *enable_lane_tx = (frame >> ENABLE_LANE_TX_SHIFT)
+ & ENABLE_LANE_TX_MASK;
+ *tx_polarity_inversion = (frame >> TX_POLARITY_INVERSION_SHIFT)
+ & TX_POLARITY_INVERSION_MASK;
+ *rx_polarity_inversion = (frame >> RX_POLARITY_INVERSION_SHIFT)
+ & RX_POLARITY_INVERSION_MASK;
+ *max_rate = (frame >> MAX_RATE_SHIFT) & MAX_RATE_MASK;
+ return ret;
+}
+
+static int write_tx_settings(struct hfi1_devdata *dd,
+ u8 enable_lane_tx,
+ u8 tx_polarity_inversion,
+ u8 rx_polarity_inversion,
+ u8 max_rate)
+{
+ u32 frame;
+
+ /* no need to mask, all variable sizes match field widths */
+ frame = enable_lane_tx << ENABLE_LANE_TX_SHIFT
+ | tx_polarity_inversion << TX_POLARITY_INVERSION_SHIFT
+ | rx_polarity_inversion << RX_POLARITY_INVERSION_SHIFT
+ | max_rate << MAX_RATE_SHIFT;
+ return load_8051_config(dd, TX_SETTINGS, GENERAL_CONFIG, frame);
+}
+
+static void check_fabric_firmware_versions(struct hfi1_devdata *dd)
+{
+ u32 frame, version, prod_id;
+ int ret, lane;
+
+ /* 4 lanes */
+ for (lane = 0; lane < 4; lane++) {
+ ret = read_8051_config(dd, SPICO_FW_VERSION, lane, &frame);
+ if (ret != HCMD_SUCCESS) {
+ dd_dev_err(
+ dd,
+ "Unable to read lane %d firmware details\n",
+ lane);
+ continue;
+ }
+ version = (frame >> SPICO_ROM_VERSION_SHIFT)
+ & SPICO_ROM_VERSION_MASK;
+ prod_id = (frame >> SPICO_ROM_PROD_ID_SHIFT)
+ & SPICO_ROM_PROD_ID_MASK;
+ dd_dev_info(dd,
+ "Lane %d firmware: version 0x%04x, prod_id 0x%04x\n",
+ lane, version, prod_id);
+ }
+}
+
+/*
+ * Read an idle LCB message.
+ *
+ * Returns 0 on success, -EINVAL on error
+ */
+static int read_idle_message(struct hfi1_devdata *dd, u64 type, u64 *data_out)
+{
+ int ret;
+
+ ret = do_8051_command(dd, HCMD_READ_LCB_IDLE_MSG,
+ type, data_out);
+ if (ret != HCMD_SUCCESS) {
+ dd_dev_err(dd, "read idle message: type %d, err %d\n",
+ (u32)type, ret);
+ return -EINVAL;
+ }
+ dd_dev_info(dd, "%s: read idle message 0x%llx\n", __func__, *data_out);
+ /* return only the payload as we already know the type */
+ *data_out >>= IDLE_PAYLOAD_SHIFT;
+ return 0;
+}
+
+/*
+ * Read an idle SMA message. To be done in response to a notification from
+ * the 8051.
+ *
+ * Returns 0 on success, -EINVAL on error
+ */
+static int read_idle_sma(struct hfi1_devdata *dd, u64 *data)
+{
+ return read_idle_message(dd,
--
To unsubscribe from this list: send the line "unsubscribe linux-rdma" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
next prev parent reply other threads:[~2015-06-15 13:26 UTC|newest]
Thread overview: 64+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-06-15 13:25 [PATCH v2 00/49] Add OPA gen1 driver Mike Marciniszyn
[not found] ` <20150615132434.29741.35258.stgit-K+u1se/DcYrLESAwzcoQNrvm/XP+8Wra@public.gmane.org>
2015-06-15 13:26 ` [PATCH v2 01/49] IB/core: Add OPA Port header definitions Mike Marciniszyn
[not found] ` <20150615132603.29741.75037.stgit-K+u1se/DcYrLESAwzcoQNrvm/XP+8Wra@public.gmane.org>
2015-06-15 17:11 ` Hefty, Sean
[not found] ` <1828884A29C6694DAF28B7E6B8A82373A8FF5771-P5GAC/sN6hkd3b2yrw5b5LfspsVTdybXVpNB7YpNyf8@public.gmane.org>
2015-06-17 12:08 ` Marciniszyn, Mike
[not found] ` <32E1700B9017364D9B60AED9960492BC2575145F-RjuIdWtd+YbTXloPLtfHfbfspsVTdybXVpNB7YpNyf8@public.gmane.org>
2015-06-17 12:12 ` Hal Rosenstock
[not found] ` <55816432.906-LDSdmyG8hGV8YrgS2mwiifqBs+8SCbDb@public.gmane.org>
2015-06-17 15:32 ` Hefty, Sean
2015-06-15 13:26 ` [PATCH v2 02/49] IB/hfi1: add chip specific support part1 Mike Marciniszyn
2015-06-15 13:26 ` Mike Marciniszyn [this message]
2015-06-15 13:26 ` [PATCH v2 04/49] IB/hfi1: add chip specific support part3 Mike Marciniszyn
2015-06-15 13:26 ` [PATCH v2 05/49] IB/hfi1: add chip specific support part4 Mike Marciniszyn
2015-06-15 13:26 ` [PATCH v2 06/49] IB/hfi1: add chip register definitions Mike Marciniszyn
2015-06-15 13:26 ` [PATCH v2 07/49] IB/hfi1: add chip specific headers Mike Marciniszyn
2015-06-15 13:26 ` [PATCH v2 08/49] IB/hfi1: add common header file definitions Mike Marciniszyn
2015-06-15 13:26 ` [PATCH v2 09/49] IB/hfi1: add completion queue processing Mike Marciniszyn
2015-06-15 13:26 ` [PATCH v2 10/49] IB/hfi1: add debugfs handling Mike Marciniszyn
2015-06-15 13:26 ` [PATCH v2 11/49] IB/hfi1: add char device instantiation code Mike Marciniszyn
2015-06-15 13:27 ` [PATCH v2 12/49] IB/hfi1: add diagnostic hooks Mike Marciniszyn
2015-06-15 13:27 ` [PATCH v2 13/49] IB/hfi1: add dma operation hooks Mike Marciniszyn
2015-06-15 13:27 ` [PATCH v2 14/49] IB/hfi1: add low lower receive functions Mike Marciniszyn
2015-06-15 13:27 ` [PATCH v2 15/49] IB/hfi1: add eeprom hooks Mike Marciniszyn
2015-06-15 13:27 ` [PATCH v2 16/49] IB/hfi1: add PSM driver control/data path Mike Marciniszyn
2015-06-15 13:27 ` [PATCH v2 17/49] IB/hfi1: add firmware hooks Mike Marciniszyn
2015-06-15 13:27 ` [PATCH v2 18/49] IB/hfi1: add general hfi header file Mike Marciniszyn
2015-06-15 13:27 ` [PATCH v2 19/49] IB/hfi1: add module init hooks Mike Marciniszyn
2015-06-15 13:27 ` [PATCH v2 20/49] IB/hfi1: add interrupt hooks Mike Marciniszyn
2015-06-15 13:27 ` [PATCH v2 21/49] IB/hfi1: add progress delay/restart hooks Mike Marciniszyn
2015-06-15 13:27 ` [PATCH v2 22/49] IB/hfi1: add rkey/lkey validation Mike Marciniszyn
2015-06-15 13:28 ` [PATCH v2 23/49] IB/hfi1: add OPA mad handling part1 Mike Marciniszyn
2015-06-15 13:28 ` [PATCH v2 24/49] IB/hfi1: add OPA mad handling part2 Mike Marciniszyn
2015-06-15 13:28 ` [PATCH v2 25/49] IB/hfi1: add local mad header Mike Marciniszyn
[not found] ` <20150615132813.29741.3528.stgit-K+u1se/DcYrLESAwzcoQNrvm/XP+8Wra@public.gmane.org>
2015-06-15 23:27 ` Hefty, Sean
[not found] ` <1828884A29C6694DAF28B7E6B8A82373A8FF5B18-P5GAC/sN6hkd3b2yrw5b5LfspsVTdybXVpNB7YpNyf8@public.gmane.org>
2015-06-17 11:51 ` Marciniszyn, Mike
2015-06-15 13:28 ` [PATCH v2 26/49] IB/hfi1: add user/kernel memory sharing hooks Mike Marciniszyn
2015-06-15 13:28 ` [PATCH v2 27/49] IB/hfi1: add memory region handling Mike Marciniszyn
2015-06-15 13:28 ` [PATCH v2 28/49] IB/hfi1: add misc OPA defines Mike Marciniszyn
2015-06-15 13:28 ` [PATCH v2 29/49] IB/hfi1: add pcie routines Mike Marciniszyn
2015-06-15 13:28 ` [PATCH v2 30/49] IB/hfi1: add pio handling Mike Marciniszyn
2015-06-15 13:28 ` [PATCH v2 31/49] IB/hfi1: add platform config definitions Mike Marciniszyn
2015-06-15 13:28 ` [PATCH v2 32/49] IB/hfi1: add qp handling Mike Marciniszyn
2015-06-15 13:28 ` [PATCH v2 33/49] IB/hfi1: add qsfp handling Mike Marciniszyn
2015-06-15 13:29 ` [PATCH v2 34/49] IB/hfi1: add RC QP handling Mike Marciniszyn
2015-06-15 13:29 ` [PATCH v2 35/49] IB/hfi1: add routines for RC/UC Mike Marciniszyn
2015-06-15 13:29 ` [PATCH v2 36/49] IB/hfi1: add sdma routines Mike Marciniszyn
2015-06-15 13:29 ` [PATCH v2 37/49] IB/hfi1: add sdma header file Mike Marciniszyn
2015-06-15 13:29 ` [PATCH v2 38/49] IB/hfi1: add SRQ handling Mike Marciniszyn
2015-06-15 13:29 ` [PATCH v2 39/49] IB/hfi1: add sysfs routines Mike Marciniszyn
[not found] ` <20150615132929.29741.87559.stgit-K+u1se/DcYrLESAwzcoQNrvm/XP+8Wra@public.gmane.org>
2015-06-15 19:14 ` Or Gerlitz
[not found] ` <CAJ3xEMiiqY04q4pnjRSm=7UBnS_jQJP-KhAkYEvu7FAu-F98sA-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org>
2015-06-15 19:20 ` Or Gerlitz
[not found] ` <CAJ3xEMiJ_0pFUvPJN7ov50v0hOZVsN7qC27ZbG5+pfmVuZQuMw-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org>
2015-06-17 11:48 ` Marciniszyn, Mike
[not found] ` <32E1700B9017364D9B60AED9960492BC257513D9-RjuIdWtd+YbTXloPLtfHfbfspsVTdybXVpNB7YpNyf8@public.gmane.org>
2015-06-17 15:50 ` Or Gerlitz
[not found] ` <CAJ3xEMjdhyk2OOfeCV4sZMF=Fh06H-hJn_2y85V0eBLYBBgPiA-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org>
2015-07-08 22:32 ` Marciniszyn, Mike
[not found] ` <32E1700B9017364D9B60AED9960492BC2575DB49-RjuIdWtd+YbTXloPLtfHfbfspsVTdybXVpNB7YpNyf8@public.gmane.org>
2015-07-08 23:22 ` ira.weiny
2015-06-15 13:29 ` [PATCH v2 40/49] IB/hfi1: add tracepoint debug routines Mike Marciniszyn
2015-06-15 13:29 ` [PATCH v2 41/49] IB/hfi1: add QSFP twsi routines Mike Marciniszyn
2015-06-15 13:29 ` [PATCH v2 42/49] IB/hfi1: add UC QP handling Mike Marciniszyn
2015-06-15 13:29 ` [PATCH v2 43/49] IB/hfi1: add UD " Mike Marciniszyn
2015-06-15 13:29 ` [PATCH v2 44/49] IB/hfi1: add low level page locking Mike Marciniszyn
2015-06-15 13:30 ` [PATCH v2 45/49] IB/hfi1: add PSM sdma hooks Mike Marciniszyn
2015-06-15 13:30 ` [PATCH v2 46/49] IB/hfi1: add general verbs handling Mike Marciniszyn
2015-06-15 13:30 ` [PATCH v2 47/49] IB/hfi1: add multicast routines Mike Marciniszyn
[not found] ` <20150615133012.29741.61892.stgit-K+u1se/DcYrLESAwzcoQNrvm/XP+8Wra@public.gmane.org>
2015-06-15 17:24 ` Christoph Lameter
[not found] ` <alpine.DEB.2.11.1506151222560.20941-wcBtFHqTun5QOdAKl3ChDw@public.gmane.org>
2015-06-17 12:14 ` Marciniszyn, Mike
2015-06-15 13:30 ` [PATCH v2 48/49] IB/hfi1: add driver make/config files Mike Marciniszyn
2015-06-15 13:30 ` [PATCH v2 49/49] IB/core: Add opa driver to kbuild Mike Marciniszyn
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20150615132614.29741.21279.stgit@phlsvslse11.ph.intel.com \
--to=mike.marciniszyn-ral2jqcrhueavxtiumwx3w@public.gmane.org \
--cc=dledford-H+wXaHxf7aLQT0dZR+AlfA@public.gmane.org \
--cc=linux-rdma-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.