* [PATCH] arm64: dts: rockchip: rk3588s-orangepi-5: add USB-C support
@ 2024-04-15 17:03 Jimmy Hon
2024-04-16 18:07 ` Rob Herring
2024-04-17 21:09 ` Heiko Stübner
0 siblings, 2 replies; 3+ messages in thread
From: Jimmy Hon @ 2024-04-15 17:03 UTC (permalink / raw
To: Heiko Stuebner; +Cc: linux-rockchip, linux-arm-kernel, Jimmy Hon
Add support for using the Orange Pi 5 USB-C port for USB in OHCI, EHCI
or XHCI mode. Displayport AltMode is not yet supported.
Signed-off-by: Jimmy Hon <honyuenkwun@gmail.com>
---
.../boot/dts/rockchip/rk3588s-orangepi-5.dts | 106 ++++++++++++++++++
1 file changed, 106 insertions(+)
diff --git a/arch/arm64/boot/dts/rockchip/rk3588s-orangepi-5.dts b/arch/arm64/boot/dts/rockchip/rk3588s-orangepi-5.dts
index 25de4362af38..8d1a75844673 100644
--- a/arch/arm64/boot/dts/rockchip/rk3588s-orangepi-5.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3588s-orangepi-5.dts
@@ -6,6 +6,7 @@
#include <dt-bindings/leds/common.h>
#include <dt-bindings/input/input.h>
#include <dt-bindings/pinctrl/rockchip.h>
+#include <dt-bindings/usb/pd.h>
#include "rk3588s.dtsi"
/ {
@@ -212,6 +213,64 @@ &i2c6 {
pinctrl-0 = <&i2c6m3_xfer>;
status = "okay";
+ usbc0: usb-typec@22 {
+ compatible = "fcs,fusb302";
+ reg = <0x22>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <RK_PD3 IRQ_TYPE_LEVEL_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&usbc0_int>;
+ vbus-supply = <&vbus_typec>;
+ status = "okay";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ usbc0_role_sw: endpoint@0 {
+ remote-endpoint = <&dwc3_0_role_switch>;
+ };
+ };
+ };
+
+ usb_con: connector {
+ compatible = "usb-c-connector";
+ label = "USB-C";
+ data-role = "dual";
+ op-sink-microwatt = <1000000>;
+ power-role = "dual";
+ sink-pdos =
+ <PDO_FIXED(5000, 1000, PDO_FIXED_USB_COMM)>;
+ source-pdos =
+ <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>;
+ try-power-role = "source";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ usbc0_orien_sw: endpoint {
+ remote-endpoint = <&usbdp_phy0_orientation_switch>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ dp_altmode_mux: endpoint {
+ remote-endpoint = <&usbdp_phy0_dp_altmode_mux>;
+ };
+ };
+ };
+ };
+ };
+
hym8563: rtc@51 {
compatible = "haoyu,hym8563";
reg = <0x51>;
@@ -625,6 +684,14 @@ &tsadc {
status = "okay";
};
+&u2phy0 {
+ status = "okay";
+};
+
+&u2phy0_otg {
+ status = "okay";
+};
+
&u2phy2 {
status = "okay";
};
@@ -646,6 +713,29 @@ &uart2 {
status = "okay";
};
+&usbdp_phy0 {
+ mode-switch;
+ orientation-switch;
+ sbu1-dc-gpios = <&gpio4 RK_PA5 GPIO_ACTIVE_HIGH>;
+ sbu2-dc-gpios = <&gpio4 RK_PA7 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+
+ port {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ usbdp_phy0_orientation_switch: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&usbc0_orien_sw>;
+ };
+
+ usbdp_phy0_dp_altmode_mux: endpoint@1 {
+ reg = <1>;
+ remote-endpoint = <&dp_altmode_mux>;
+ };
+ };
+};
+
&usb_host0_ehci {
status = "okay";
};
@@ -654,6 +744,22 @@ &usb_host0_ohci {
status = "okay";
};
+&usb_host0_xhci {
+ dr_mode = "otg";
+ usb-role-switch;
+ status = "okay";
+
+ port {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ dwc3_0_role_switch: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&usbc0_role_sw>;
+ };
+ };
+};
+
&usb_host1_ehci {
status = "okay";
};
--
2.44.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 3+ messages in thread
* Re: [PATCH] arm64: dts: rockchip: rk3588s-orangepi-5: add USB-C support
2024-04-15 17:03 [PATCH] arm64: dts: rockchip: rk3588s-orangepi-5: add USB-C support Jimmy Hon
@ 2024-04-16 18:07 ` Rob Herring
2024-04-17 21:09 ` Heiko Stübner
1 sibling, 0 replies; 3+ messages in thread
From: Rob Herring @ 2024-04-16 18:07 UTC (permalink / raw
To: Jimmy Hon; +Cc: linux-rockchip, linux-arm-kernel, Heiko Stuebner
On Mon, 15 Apr 2024 12:03:31 -0500, Jimmy Hon wrote:
> Add support for using the Orange Pi 5 USB-C port for USB in OHCI, EHCI
> or XHCI mode. Displayport AltMode is not yet supported.
>
> Signed-off-by: Jimmy Hon <honyuenkwun@gmail.com>
> ---
> .../boot/dts/rockchip/rk3588s-orangepi-5.dts | 106 ++++++++++++++++++
> 1 file changed, 106 insertions(+)
>
My bot found new DTB warnings on the .dts files added or changed in this
series.
Some warnings may be from an existing SoC .dtsi. Or perhaps the warnings
are fixed by another series. Ultimately, it is up to the platform
maintainer whether these warnings are acceptable or not. No need to reply
unless the platform maintainer has comments.
If you already ran DT checks and didn't see these error(s), then
make sure dt-schema is up to date:
pip3 install dtschema --upgrade
New warnings running 'make CHECK_DTBS=y rockchip/rk3588s-orangepi-5.dtb' for 20240415170331.1587-1-honyuenkwun@gmail.com:
arch/arm64/boot/dts/rockchip/rk3588s-orangepi-5.dtb: usb-typec@22: 'ports' does not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/usb/fcs,fusb302.yaml#
arch/arm64/boot/dts/rockchip/rk3588s-orangepi-5.dtb: gpio-func: leds-gpio: {'rockchip,pins': [[0, 2, 0, 231]], 'phandle': [[239]]} is not of type 'array'
from schema $id: http://devicetree.org/schemas/gpio/gpio-consumer.yaml#
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 3+ messages in thread
* Re: [PATCH] arm64: dts: rockchip: rk3588s-orangepi-5: add USB-C support
2024-04-15 17:03 [PATCH] arm64: dts: rockchip: rk3588s-orangepi-5: add USB-C support Jimmy Hon
2024-04-16 18:07 ` Rob Herring
@ 2024-04-17 21:09 ` Heiko Stübner
1 sibling, 0 replies; 3+ messages in thread
From: Heiko Stübner @ 2024-04-17 21:09 UTC (permalink / raw
To: Jimmy Hon; +Cc: linux-rockchip, linux-arm-kernel, Jimmy Hon
Hi Jimmy,
Am Montag, 15. April 2024, 19:03:31 CEST schrieb Jimmy Hon:
> Add support for using the Orange Pi 5 USB-C port for USB in OHCI, EHCI
> or XHCI mode. Displayport AltMode is not yet supported.
>
> Signed-off-by: Jimmy Hon <honyuenkwun@gmail.com>
[...]
> + usbc0: usb-typec@22 {
> + compatible = "fcs,fusb302";
> + reg = <0x22>;
> + interrupt-parent = <&gpio0>;
> + interrupts = <RK_PD3 IRQ_TYPE_LEVEL_LOW>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&usbc0_int>;
> + vbus-supply = <&vbus_typec>;
> + status = "okay";
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> +
> + usbc0_role_sw: endpoint@0 {
> + remote-endpoint = <&dwc3_0_role_switch>;
> + };
> + };
> + };
as you already saw from the mail of Rob's bot, this does not belong here
in the mainline kernel.
> + usb_con: connector {
> + compatible = "usb-c-connector";
> + label = "USB-C";
> + data-role = "dual";
> + op-sink-microwatt = <1000000>;
> + power-role = "dual";
> + sink-pdos =
> + <PDO_FIXED(5000, 1000, PDO_FIXED_USB_COMM)>;
> + source-pdos =
> + <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>;
> + try-power-role = "source";
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> +
> + usbc0_orien_sw: endpoint {
> + remote-endpoint = <&usbdp_phy0_orientation_switch>;
> + };
> + };
> +
> + port@1 {
> + reg = <1>;
> +
> + dp_altmode_mux: endpoint {
> + remote-endpoint = <&usbdp_phy0_dp_altmode_mux>;
> + };
> + };
these ports also look like they do not follow the binding.
The type-c-connector binding specifies the ports as
- port@1: High Speed (HS) data bus to the connector
- port@2: Siper Speed (SS) data bus to the connector
- port@3: Sideband Use (SBU) - the alternate mode
> + };
> + };
> + };
> +
> hym8563: rtc@51 {
> compatible = "haoyu,hym8563";
> reg = <0x51>;
> @@ -625,6 +684,14 @@ &tsadc {
> status = "okay";
> };
>
> +&u2phy0 {
> + status = "okay";
> +};
> +
> +&u2phy0_otg {
> + status = "okay";
> +};
> +
> &u2phy2 {
> status = "okay";
> };
> @@ -646,6 +713,29 @@ &uart2 {
> status = "okay";
> };
>
> +&usbdp_phy0 {
> + mode-switch;
> + orientation-switch;
> + sbu1-dc-gpios = <&gpio4 RK_PA5 GPIO_ACTIVE_HIGH>;
> + sbu2-dc-gpios = <&gpio4 RK_PA7 GPIO_ACTIVE_HIGH>;
> + status = "okay";
> +
> + port {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + usbdp_phy0_orientation_switch: endpoint@0 {
> + reg = <0>;
> + remote-endpoint = <&usbc0_orien_sw>;
> + };
> +
> + usbdp_phy0_dp_altmode_mux: endpoint@1 {
> + reg = <1>;
> + remote-endpoint = <&dp_altmode_mux>;
> + };
> + };
> +};
> +
> &usb_host0_ehci {
> status = "okay";
> };
> @@ -654,6 +744,22 @@ &usb_host0_ohci {
> status = "okay";
> };
>
> +&usb_host0_xhci {
> + dr_mode = "otg";
> + usb-role-switch;
> + status = "okay";
> +
> + port {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + dwc3_0_role_switch: endpoint@0 {
> + reg = <0>;
this only has one endpoint, so you should be able to live without the @0
and the reg and could also drop the #address-cells + #size-cells above?
> + remote-endpoint = <&usbc0_role_sw>;
> + };
> + };
> +};
> +
> &usb_host1_ehci {
> status = "okay";
> };
>
Heiko
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2024-04-17 21:09 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2024-04-15 17:03 [PATCH] arm64: dts: rockchip: rk3588s-orangepi-5: add USB-C support Jimmy Hon
2024-04-16 18:07 ` Rob Herring
2024-04-17 21:09 ` Heiko Stübner
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for read-only IMAP folder(s) and NNTP newsgroup(s).