From: Daniel Golle <daniel@makrotopia.org>
To: Frank Wunderlich <frank-w@public-files.de>
Cc: AngeloGioacchino Del Regno
<angelogioacchino.delregno@collabora.com>,
Frank Wunderlich <linux@fw-web.de>, Rob Herring <robh@kernel.org>,
Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
Conor Dooley <conor+dt@kernel.org>,
Michael Turquette <mturquette@baylibre.com>,
Stephen Boyd <sboyd@kernel.org>, Pavel Machek <pavel@ucw.cz>,
Lee Jones <lee@kernel.org>,
"David S. Miller" <davem@davemloft.net>,
Eric Dumazet <edumazet@google.com>,
Jakub Kicinski <kuba@kernel.org>, Paolo Abeni <pabeni@redhat.com>,
Matthias Brugger <matthias.bgg@gmail.com>,
Eric Woudstra <ericwouds@gmail.com>,
Tianling Shen <cnsztl@immortalwrt.org>,
devicetree@vger.kernel.org, linux-kernel@vger.kernel.org,
linux-clk@vger.kernel.org, linux-leds@vger.kernel.org,
netdev@vger.kernel.org, linux-arm-kernel@lists.infradead.org,
linux-mediatek@lists.infradead.org,
Tianling Shen <cnsztl@gmail.com>
Subject: Re: [RFC v1 5/5] arm64: dts: mediatek: Add mt7986 based Bananapi R3 Mini
Date: Mon, 6 May 2024 17:12:15 +0100 [thread overview]
Message-ID: <ZjkBX9T_xzx1D66m@makrotopia.org> (raw)
In-Reply-To: <3E013BA7-0264-4AC3-B677-BDD16B1F8D90@public-files.de>
On Mon, May 06, 2024 at 06:00:30PM +0200, Frank Wunderlich wrote:
> Hi
>
> Thanks for review.
>
> Am 6. Mai 2024 14:48:59 MESZ schrieb AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>:
> >Il 05/05/24 18:45, Frank Wunderlich ha scritto:
> >> From: Frank Wunderlich <frank-w@public-files.de>
> >>
> >> Add device Tree for Bananapi R3 Mini SBC.
> >>
> >> Co-developed-by: Eric Woudstra <ericwouds@gmail.com>
> >> Signed-off-by: Eric Woudstra <ericwouds@gmail.com>
> >> Co-developed-by: Tianling Shen <cnsztl@gmail.com>
> >> Signed-off-by: Tianling Shen <cnsztl@gmail.com>
> >> Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
> >> ---
> >> arch/arm64/boot/dts/mediatek/Makefile | 1 +
> >> .../mediatek/mt7986a-bananapi-bpi-r3-mini.dts | 486 ++++++++++++++++++
> >> 2 files changed, 487 insertions(+)
> >> create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-mini.dts
> >>
> >> diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile
> >> index 37b4ca3a87c9..1763b001ab06 100644
> >> --- a/arch/arm64/boot/dts/mediatek/Makefile
> >> +++ b/arch/arm64/boot/dts/mediatek/Makefile
> >> @@ -11,6 +11,7 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-bananapi-bpi-r64.dtb
> >> dtb-$(CONFIG_ARCH_MEDIATEK) += mt7981b-xiaomi-ax3000t.dtb
> >> dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-acelink-ew-7886cax.dtb
> >> dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3.dtb
> >> +dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-mini.dtb
> >> dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-emmc.dtbo
> >> dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-nand.dtbo
> >> dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-nor.dtbo
> >> diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-mini.dts b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-mini.dts
> >> new file mode 100644
> >> index 000000000000..c764b4dc4752
> >> --- /dev/null
> >> +++ b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-mini.dts
> >> @@ -0,0 +1,486 @@
> >> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> >> +/*
> >> + * Copyright (C) 2021 MediaTek Inc.
> >> + * Authors: Frank Wunderlich <frank-w@public-files.de>
> >> + * Eric Woudstra <ericwouds@gmail.com>
> >> + * Tianling Shen <cnsztl@immortalwrt.org>
> >> + */
> >> +
> >> +/dts-v1/;
> >> +
> >> +#include <dt-bindings/gpio/gpio.h>
> >> +#include <dt-bindings/input/input.h>
> >> +#include <dt-bindings/leds/common.h>
> >> +#include <dt-bindings/pinctrl/mt65xx.h>
> >> +
> >> +#include "mt7986a.dtsi"
> >> +
> >> +/ {
> >> + model = "Bananapi BPI-R3 Mini";
> >> + chassis-type = "embedded";
> >> + compatible = "bananapi,bpi-r3mini", "mediatek,mt7986a";
> >> +
> >> + aliases {
> >> + serial0 = &uart0;
> >> + ethernet0 = &gmac0;
> >> + ethernet1 = &gmac1;
> >> + };
> >> +
> >> + chosen {
> >> + stdout-path = "serial0:115200n8";
> >> + };
> >> +
> >> + dcin: regulator-12vd {
> >> + compatible = "regulator-fixed";
> >> + regulator-name = "12vd";
> >> + regulator-min-microvolt = <12000000>;
> >> + regulator-max-microvolt = <12000000>;
> >> + regulator-boot-on;
> >> + regulator-always-on;
> >> + };
> >> +
> >> + fan: pwm-fan {
> >> + compatible = "pwm-fan";
> >> + #cooling-cells = <2>;
> >> + /* cooling level (0, 1, 2) - pwm inverted */
> >> + cooling-levels = <255 96 0>;
> >
> >Did you try to actually invert the PWM?
> >
> >Look for PWM_POLARITY_INVERTED ;-)
>
> Mtk pwm driver does not support it
>
> https://elixir.bootlin.com/linux/latest/source/drivers/pwm/pwm-mediatek.c#L211
>
> >> + pwms = <&pwm 0 10000>;
> >> + status = "okay";
> >> + };
> >> +
> >> + reg_1p8v: regulator-1p8v {
> >> + compatible = "regulator-fixed";
> >> + regulator-name = "1.8vd";
> >> + regulator-min-microvolt = <1800000>;
> >> + regulator-max-microvolt = <1800000>;
> >> + regulator-boot-on;
> >> + regulator-always-on;
> >> + vin-supply = <&dcin>;
> >> + };
> >> +
> >> + reg_3p3v: regulator-3p3v {
> >> + compatible = "regulator-fixed";
> >> + regulator-name = "3.3vd";
> >> + regulator-min-microvolt = <3300000>;
> >> + regulator-max-microvolt = <3300000>;
> >> + regulator-boot-on;
> >> + regulator-always-on;
> >> + vin-supply = <&dcin>;
> >> + };
> >> +
> >> + usb_vbus: regulator-usb-vbus {
> >> + compatible = "regulator-fixed";
> >> + regulator-name = "usb_vbus";
> >> + regulator-min-microvolt = <5000000>;
> >> + regulator-max-microvolt = <5000000>;
> >> + gpios = <&pio 20 GPIO_ACTIVE_LOW>;
> >> + regulator-boot-on;
> >> + };
> >> +
> >> + en8811_a: regulator-phy1 {
> >> + compatible = "regulator-fixed";
> >> + regulator-name = "phy1";
> >> + regulator-min-microvolt = <3300000>;
> >> + regulator-max-microvolt = <3300000>;
> >> + gpio = <&pio 16 GPIO_ACTIVE_LOW>;
> >> + regulator-always-on;
> >> + };
> >> +
> >> + en8811_b: regulator-phy2 {
> >> + compatible = "regulator-fixed";
> >> + regulator-name = "phy2";
> >> + regulator-min-microvolt = <3300000>;
> >> + regulator-max-microvolt = <3300000>;
> >> + gpio = <&pio 17 GPIO_ACTIVE_LOW>;
> >> + regulator-always-on;
> >> + };
> >> +
> >> + leds {
> >> + compatible = "gpio-leds";
> >> +
> >> + green_led: led-0 {
> >> + color = <LED_COLOR_ID_GREEN>;
> >> + function = LED_FUNCTION_POWER;
> >> + gpios = <&pio 19 GPIO_ACTIVE_HIGH>;
> >> + default-state = "on";
> >> + };
> >> + };
> >> +
> >> + gpio-keys {
> >> + compatible = "gpio-keys";
> >> +
> >> + reset-key {
> >> + label = "reset";
> >> + linux,code = <KEY_RESTART>;
> >> + gpios = <&pio 7 GPIO_ACTIVE_LOW>;
> >> + };
> >> + };
> >> +
> >> +};
> >> +
> >> +&cpu_thermal {
> >> + cooling-maps {
> >> + map0 {
> >> + /* active: set fan to cooling level 2 */
> >> + cooling-device = <&fan 2 2>;
> >> + trip = <&cpu_trip_active_high>;
> >> + };
> >> +
> >> + map1 {
> >> + /* active: set fan to cooling level 1 */
> >> + cooling-device = <&fan 1 1>;
> >> + trip = <&cpu_trip_active_med>;
> >> + };
> >> +
> >> + map2 {
> >> + /* active: set fan to cooling level 0 */
> >> + cooling-device = <&fan 0 0>;
> >> + trip = <&cpu_trip_active_low>;
> >> + };
> >> + };
> >> +};
> >> +
> >> +&crypto {
> >> + status = "okay";
> >> +};
> >> +
> >> +ð {
> >> + status = "okay";
> >> +
> >> + gmac0: mac@0 {
> >> + compatible = "mediatek,eth-mac";
> >> + reg = <0>;
> >> + phy-mode = "2500base-x";
> >> + phy-handle = <&phy14>;
> >> + };
> >> +
> >> + gmac1: mac@1 {
> >> + compatible = "mediatek,eth-mac";
> >> + reg = <1>;
> >> + phy-mode = "2500base-x";
> >> + phy-handle = <&phy15>;
> >> + };
> >> +
> >> + mdio: mdio-bus {
> >> + #address-cells = <1>;
> >> + #size-cells = <0>;
> >> + };
> >> +};
> >> +
> >> +&mmc0 {
> >> + pinctrl-names = "default", "state_uhs";
> >> + pinctrl-0 = <&mmc0_pins_default>;
> >> + pinctrl-1 = <&mmc0_pins_uhs>;
> >> + vmmc-supply = <®_3p3v>;
> >> + vqmmc-supply = <®_1p8v>;
> >> +};
> >> +
> >> +
> >> +&i2c0 {
> >> + pinctrl-names = "default";
> >> + pinctrl-0 = <&i2c_pins>;
> >> + status = "okay";
> >> +
> >> + /* MAC Address EEPROM */
> >> + eeprom@50 {
> >> + compatible = "atmel,24c02";
> >> + reg = <0x50>;
> >> +
> >> + address-width = <8>;
> >> + pagesize = <8>;
> >> + size = <256>;
> >> + };
> >> +};
> >> +
> >> +&mdio {
> >
> >You can just move all this stuff to where you declare the mdio-bus....
>
> Ok,see these 2 lines are already above,so can be dropped here.
>
> >> + #address-cells = <1>;
> >> + #size-cells = <0>;
> >> +
> >> + phy14: ethernet-phy@14 {
> >
> >I say that this is `phy0: ethernet-phy@14` - because this is the first PHY on this
> >board.
>
> Ok,i change this and phy15
>
> >> + reg = <14>;
> >
> >Uhm.. doesn't this require the ethernet-phy-id03a2.a411 compatible?
>
> I can add it,but worked without it.
>
> There was a discussion about that and result was we don't need it in board dts,maybe add compatible in binding example.
>
> https://patchwork.kernel.org/project/netdevbpf/patch/20240206194751.1901802-2-ericwouds@gmail.com/#25703356
I confirm that setting the PHY ID in DT is **not** needed.
The PHY probes fine and it's possible to read the PHY ID even before
firmware has been loaded.
>
> >> + interrupts-extended = <&pio 48 IRQ_TYPE_EDGE_FALLING>;
> >> + reset-gpios = <&pio 49 GPIO_ACTIVE_LOW>;
> >> + reset-assert-us = <10000>;
> >> + reset-deassert-us = <20000>;
> >> + phy-mode = "2500base-x";
> >> + full-duplex;
> >> + pause;
> >> + airoha,pnswap-rx;
> >> +
> >> + leds {
> >> + #address-cells = <1>;
> >> + #size-cells = <0>;
> >> +
> >> + led@0 { /* en8811_a_gpio5 */
> >> + reg = <0>;
> >> + color = <LED_COLOR_ID_YELLOW>;
> >> + function = LED_FUNCTION_LAN;
> >> + function-enumerator = <1>;
> >
> >Why aren't you simply using a label?
>
> You mean the comment? I can add it of course like for regulators.
>
> >> + default-state = "keep";
> >> + linux,default-trigger = "netdev";
Using linux,default-trigger = "netdev" will NOT work as intended,
see also the reply to your other patch where you are adding netdev
trigger to dt-bindings.
If you do this, it will seemingly work, but if you check
/sys/class/leds/foo/hw_control
it will always be 0, and hardware offloading will hence never be used.
Please just set the LED trigger in userspace for now.
> >> + };
> >> + led@1 { /* en8811_a_gpio4 */
> >> + reg = <1>;
> >> + color = <LED_COLOR_ID_GREEN>;
> >> + function = LED_FUNCTION_LAN;
> >> + function-enumerator = <2>;
> >> + default-state = "keep";
> >> + linux,default-trigger = "netdev";
> >> + };
> >> + };
> >> + };
> >> +
> >> + phy15: ethernet-phy@15 {
> >> + reg = <15>;
> >
> >Same here.
> >
> >Cheers,
> >Angelo
> >
>
>
> regards Frank
>
next prev parent reply other threads:[~2024-05-06 16:12 UTC|newest]
Thread overview: 30+ messages / expand[flat|nested] mbox.gz Atom feed top
2024-05-05 16:45 [RFC v1 0/5] Add Bananapi R3 Mini Frank Wunderlich
2024-05-05 16:45 ` [RFC v1 1/5] dt-bindings: leds: add led trigger netdev Frank Wunderlich
2024-05-06 8:18 ` Krzysztof Kozlowski
2024-05-06 8:59 ` Daniel Golle
2024-05-06 17:10 ` Aw: " Frank Wunderlich
2024-05-07 6:10 ` Krzysztof Kozlowski
2024-05-05 16:45 ` [RFC v1 2/5] dt-bindings: clock: mediatek: add address-cells and size-cells to ethsys Frank Wunderlich
2024-05-06 8:18 ` Krzysztof Kozlowski
2024-05-06 16:51 ` Aw: " Frank Wunderlich
2024-05-07 19:35 ` Rob Herring
2024-05-07 21:22 ` Aw: " Frank Wunderlich
2024-05-06 12:48 ` AngeloGioacchino Del Regno
2024-05-06 16:01 ` Frank Wunderlich
2024-05-07 13:36 ` AngeloGioacchino Del Regno
2024-05-05 16:45 ` [RFC v1 3/5] dt-bindings: net: mediatek,net: add reset-cells Frank Wunderlich
2024-05-06 8:19 ` Krzysztof Kozlowski
2024-05-07 19:37 ` Rob Herring
2024-05-05 16:45 ` [RFC v1 4/5] dt-bindings: arm64: dts: mediatek: add BananaPi R3 Mini Frank Wunderlich
2024-05-05 16:45 ` [RFC v1 5/5] arm64: dts: mediatek: Add mt7986 based Bananapi " Frank Wunderlich
2024-05-06 8:20 ` Krzysztof Kozlowski
2024-05-06 16:40 ` Aw: " Frank Wunderlich
2024-05-06 12:48 ` AngeloGioacchino Del Regno
2024-05-06 16:00 ` Frank Wunderlich
2024-05-06 16:12 ` Daniel Golle [this message]
2024-05-07 13:35 ` AngeloGioacchino Del Regno
2024-05-08 18:25 ` Aw: " Frank Wunderlich
2024-05-09 10:10 ` AngeloGioacchino Del Regno
2024-05-09 10:30 ` Frank Wunderlich
2024-05-09 10:35 ` AngeloGioacchino Del Regno
2024-05-06 20:40 ` [RFC v1 0/5] Add " Rob Herring (Arm)
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=ZjkBX9T_xzx1D66m@makrotopia.org \
--to=daniel@makrotopia.org \
--cc=angelogioacchino.delregno@collabora.com \
--cc=cnsztl@gmail.com \
--cc=cnsztl@immortalwrt.org \
--cc=conor+dt@kernel.org \
--cc=davem@davemloft.net \
--cc=devicetree@vger.kernel.org \
--cc=edumazet@google.com \
--cc=ericwouds@gmail.com \
--cc=frank-w@public-files.de \
--cc=krzysztof.kozlowski+dt@linaro.org \
--cc=kuba@kernel.org \
--cc=lee@kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-clk@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-leds@vger.kernel.org \
--cc=linux-mediatek@lists.infradead.org \
--cc=linux@fw-web.de \
--cc=matthias.bgg@gmail.com \
--cc=mturquette@baylibre.com \
--cc=netdev@vger.kernel.org \
--cc=pabeni@redhat.com \
--cc=pavel@ucw.cz \
--cc=robh@kernel.org \
--cc=sboyd@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for read-only IMAP folder(s) and NNTP newsgroup(s).