From: Dmitry Rokosov <ddrokosov@salutedevices.com>
To: <neil.armstrong@linaro.org>, <jbrunet@baylibre.com>,
<mturquette@baylibre.com>, <sboyd@kernel.org>,
<robh+dt@kernel.org>, <krzysztof.kozlowski+dt@linaro.org>,
<khilman@baylibre.com>, <martin.blumenstingl@googlemail.com>
Cc: <jian.hu@amlogic.com>, <kernel@sberdevices.ru>,
<rockosov@gmail.com>, <linux-amlogic@lists.infradead.org>,
<linux-clk@vger.kernel.org>, <devicetree@vger.kernel.org>,
<linux-kernel@vger.kernel.org>,
<linux-arm-kernel@lists.infradead.org>,
Dmitry Rokosov <ddrokosov@salutedevices.com>
Subject: [PATCH v2 7/7] clk: meson: a1: add Amlogic A1 CPU clock controller driver
Date: Fri, 10 May 2024 12:08:59 +0300 [thread overview]
Message-ID: <20240510090933.19464-8-ddrokosov@salutedevices.com> (raw)
In-Reply-To: <20240510090933.19464-1-ddrokosov@salutedevices.com>
The CPU clock controller plays a general role in the Amlogic A1 SoC
family by generating CPU clocks. As an APB slave module, it offers the
capability to inherit the CPU clock from two sources: the internal fixed
clock known as 'cpu fixed clock' and the external input provided by the
A1 PLL clock controller, referred to as 'syspll'.
It is important for the driver to handle cpu_clk rate switching
effectively by transitioning to the CPU fixed clock to avoid any
potential execution freezes.
Signed-off-by: Dmitry Rokosov <ddrokosov@salutedevices.com>
---
drivers/clk/meson/Kconfig | 10 ++
drivers/clk/meson/Makefile | 1 +
drivers/clk/meson/a1-cpu.c | 331 +++++++++++++++++++++++++++++++++++++
3 files changed, 342 insertions(+)
create mode 100644 drivers/clk/meson/a1-cpu.c
diff --git a/drivers/clk/meson/Kconfig b/drivers/clk/meson/Kconfig
index 80c4a18c83d2..148d4495eee3 100644
--- a/drivers/clk/meson/Kconfig
+++ b/drivers/clk/meson/Kconfig
@@ -111,6 +111,16 @@ config COMMON_CLK_AXG_AUDIO
Support for the audio clock controller on AmLogic A113D devices,
aka axg, Say Y if you want audio subsystem to work.
+config COMMON_CLK_A1_CPU
+ tristate "Amlogic A1 SoC CPU controller support"
+ depends on ARM64
+ select COMMON_CLK_MESON_REGMAP
+ select COMMON_CLK_MESON_CLKC_UTILS
+ help
+ Support for the CPU clock controller on Amlogic A113L based
+ device, A1 SoC Family. Say Y if you want A1 CPU clock controller
+ to work.
+
config COMMON_CLK_A1_PLL
tristate "Amlogic A1 SoC PLL controller support"
depends on ARM64
diff --git a/drivers/clk/meson/Makefile b/drivers/clk/meson/Makefile
index 4968fc7ad555..2a06eb0303d6 100644
--- a/drivers/clk/meson/Makefile
+++ b/drivers/clk/meson/Makefile
@@ -18,6 +18,7 @@ obj-$(CONFIG_COMMON_CLK_MESON_AUDIO_RSTC) += meson-audio-rstc.o
obj-$(CONFIG_COMMON_CLK_AXG) += axg.o axg-aoclk.o
obj-$(CONFIG_COMMON_CLK_AXG_AUDIO) += axg-audio.o
+obj-$(CONFIG_COMMON_CLK_A1_CPU) += a1-cpu.o
obj-$(CONFIG_COMMON_CLK_A1_PLL) += a1-pll.o
obj-$(CONFIG_COMMON_CLK_A1_PERIPHERALS) += a1-peripherals.o
obj-$(CONFIG_COMMON_CLK_A1_AUDIO) += a1-audio.o
diff --git a/drivers/clk/meson/a1-cpu.c b/drivers/clk/meson/a1-cpu.c
new file mode 100644
index 000000000000..a9edabeafea9
--- /dev/null
+++ b/drivers/clk/meson/a1-cpu.c
@@ -0,0 +1,331 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Amlogic A1 SoC family CPU Clock Controller driver.
+ *
+ * Copyright (c) 2024, SaluteDevices. All Rights Reserved.
+ * Author: Dmitry Rokosov <ddrokosov@salutedevices.com>
+ */
+
+#include <linux/clk.h>
+#include <linux/clk-provider.h>
+#include <linux/mod_devicetable.h>
+#include <linux/platform_device.h>
+#include "clk-regmap.h"
+#include "meson-clkc-utils.h"
+
+#include <dt-bindings/clock/amlogic,a1-cpu-clkc.h>
+
+/* CPU Clock Controller register offset */
+#define CPUCTRL_CLK_CTRL0 0x0
+#define CPUCTRL_CLK_CTRL1 0x4
+
+static u32 cpu_fsource_sel_table[] = { 0, 1, 2 };
+static const struct clk_parent_data cpu_fsource_sel_parents[] = {
+ { .fw_name = "xtal" },
+ { .fw_name = "fclk_div2" },
+ { .fw_name = "fclk_div3" },
+};
+
+static struct clk_regmap cpu_fsource_sel0 = {
+ .data = &(struct clk_regmap_mux_data) {
+ .offset = CPUCTRL_CLK_CTRL0,
+ .mask = 0x3,
+ .shift = 0,
+ .table = cpu_fsource_sel_table,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "cpu_fsource_sel0",
+ .ops = &clk_regmap_mux_ops,
+ .parent_data = cpu_fsource_sel_parents,
+ .num_parents = ARRAY_SIZE(cpu_fsource_sel_parents),
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap cpu_fsource_div0 = {
+ .data = &(struct clk_regmap_div_data) {
+ .offset = CPUCTRL_CLK_CTRL0,
+ .shift = 4,
+ .width = 6,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "cpu_fsource_div0",
+ .ops = &clk_regmap_divider_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &cpu_fsource_sel0.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap cpu_fsel0 = {
+ .data = &(struct clk_regmap_mux_data) {
+ .offset = CPUCTRL_CLK_CTRL0,
+ .mask = 0x1,
+ .shift = 2,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "cpu_fsel0",
+ .ops = &clk_regmap_mux_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &cpu_fsource_sel0.hw,
+ &cpu_fsource_div0.hw,
+ },
+ .num_parents = 2,
+ .flags = CLK_SET_RATE_GATE | CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap cpu_fsource_sel1 = {
+ .data = &(struct clk_regmap_mux_data) {
+ .offset = CPUCTRL_CLK_CTRL0,
+ .mask = 0x3,
+ .shift = 16,
+ .table = cpu_fsource_sel_table,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "cpu_fsource_sel1",
+ .ops = &clk_regmap_mux_ops,
+ .parent_data = cpu_fsource_sel_parents,
+ .num_parents = ARRAY_SIZE(cpu_fsource_sel_parents),
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap cpu_fsource_div1 = {
+ .data = &(struct clk_regmap_div_data) {
+ .offset = CPUCTRL_CLK_CTRL0,
+ .shift = 20,
+ .width = 6,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "cpu_fsource_div1",
+ .ops = &clk_regmap_divider_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &cpu_fsource_sel1.hw
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap cpu_fsel1 = {
+ .data = &(struct clk_regmap_mux_data) {
+ .offset = CPUCTRL_CLK_CTRL0,
+ .mask = 0x1,
+ .shift = 18,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "cpu_fsel1",
+ .ops = &clk_regmap_mux_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &cpu_fsource_sel1.hw,
+ &cpu_fsource_div1.hw,
+ },
+ .num_parents = 2,
+ .flags = CLK_SET_RATE_GATE | CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap cpu_fclk = {
+ .data = &(struct clk_regmap_mux_data) {
+ .offset = CPUCTRL_CLK_CTRL0,
+ .mask = 0x1,
+ .shift = 10,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "cpu_fclk",
+ .ops = &clk_regmap_mux_ops,
+ .parent_hws = (const struct clk_hw *[]) {
+ &cpu_fsel0.hw,
+ &cpu_fsel1.hw,
+ },
+ .num_parents = 2,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_regmap cpu_clk = {
+ .data = &(struct clk_regmap_mux_data) {
+ .offset = CPUCTRL_CLK_CTRL0,
+ .mask = 0x1,
+ .shift = 11,
+ },
+ .hw.init = &(struct clk_init_data) {
+ .name = "cpu_clk",
+ .ops = &clk_regmap_mux_ops,
+ .parent_data = (const struct clk_parent_data []) {
+ { .hw = &cpu_fclk.hw },
+ { .fw_name = "sys_pll", },
+ },
+ .num_parents = 2,
+ .flags = CLK_SET_RATE_PARENT | CLK_IS_CRITICAL,
+ },
+};
+
+/* Array of all clocks registered by this provider */
+static struct clk_hw *a1_cpu_hw_clks[] = {
+ [CLKID_CPU_FSOURCE_SEL0] = &cpu_fsource_sel0.hw,
+ [CLKID_CPU_FSOURCE_DIV0] = &cpu_fsource_div0.hw,
+ [CLKID_CPU_FSEL0] = &cpu_fsel0.hw,
+ [CLKID_CPU_FSOURCE_SEL1] = &cpu_fsource_sel1.hw,
+ [CLKID_CPU_FSOURCE_DIV1] = &cpu_fsource_div1.hw,
+ [CLKID_CPU_FSEL1] = &cpu_fsel1.hw,
+ [CLKID_CPU_FCLK] = &cpu_fclk.hw,
+ [CLKID_CPU_CLK] = &cpu_clk.hw,
+};
+
+static struct clk_regmap *const a1_cpu_regmaps[] = {
+ &cpu_fsource_sel0,
+ &cpu_fsource_div0,
+ &cpu_fsel0,
+ &cpu_fsource_sel1,
+ &cpu_fsource_div1,
+ &cpu_fsel1,
+ &cpu_fclk,
+ &cpu_clk,
+};
+
+static struct regmap_config a1_cpu_regmap_cfg = {
+ .reg_bits = 32,
+ .val_bits = 32,
+ .reg_stride = 4,
+ .max_register = CPUCTRL_CLK_CTRL1,
+};
+
+static struct meson_clk_hw_data a1_cpu_clks = {
+ .hws = a1_cpu_hw_clks,
+ .num = ARRAY_SIZE(a1_cpu_hw_clks),
+};
+
+struct a1_sys_pll_nb_data {
+ struct notifier_block nb;
+ struct clk_hw *cpu_clk;
+ struct clk_hw *cpu_fclk;
+ struct clk *sys_pll;
+};
+
+static int meson_a1_sys_pll_notifier_cb(struct notifier_block *nb,
+ unsigned long event, void *data)
+{
+ struct a1_sys_pll_nb_data *nbd;
+ int ret = 0;
+
+ nbd = container_of(nb, struct a1_sys_pll_nb_data, nb);
+
+ switch (event) {
+ case PRE_RATE_CHANGE:
+ /*
+ * Clock sys_pll will be changed to feed cpu_clk,
+ * configure cpu_clk to use cpu_fclk fixed clock.
+ */
+ ret = clk_hw_set_parent(nbd->cpu_clk, nbd->cpu_fclk);
+
+ /* Wait for clock propagation */
+ if (!ret)
+ udelay(100);
+
+ break;
+
+ case POST_RATE_CHANGE:
+ /*
+ * Clock sys_pll rate has ben calculated,
+ * switch back cpu_clk to sys_pll
+ */
+ ret = clk_set_parent(nbd->cpu_clk->clk, nbd->sys_pll);
+
+ /* Wait for clock propagation */
+ if (!ret)
+ udelay(100);
+ break;
+
+ default:
+ pr_warn("Unknown event %lu for sys_pll notifier\n", event);
+ break;
+ }
+
+ return notifier_from_errno(ret);
+}
+
+static struct a1_sys_pll_nb_data a1_sys_pll_nb_data = {
+ .nb.notifier_call = meson_a1_sys_pll_notifier_cb,
+ .cpu_clk = &cpu_clk.hw,
+ .cpu_fclk = &cpu_fclk.hw,
+};
+
+static int meson_a1_dvfs_setup(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct clk *sys_pll;
+ int ret;
+
+ /* Setup clock notifier for sys_pll clk */
+ sys_pll = devm_clk_get(dev, "sys_pll");
+ if (IS_ERR(sys_pll))
+ return dev_err_probe(dev, PTR_ERR(sys_pll),
+ "can't get sys_pll as notifier clock\n");
+
+ a1_sys_pll_nb_data.sys_pll = sys_pll;
+ ret = devm_clk_notifier_register(dev, sys_pll,
+ &a1_sys_pll_nb_data.nb);
+ if (ret)
+ return dev_err_probe(dev, ret,
+ "can't register sys_pll notifier\n");
+
+ return ret;
+}
+
+static int meson_a1_cpu_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ void __iomem *base;
+ struct regmap *map;
+ int clkid, i, err;
+
+ base = devm_platform_ioremap_resource(pdev, 0);
+ if (IS_ERR(base))
+ return dev_err_probe(dev, PTR_ERR(base),
+ "can't ioremap resource\n");
+
+ map = devm_regmap_init_mmio(dev, base, &a1_cpu_regmap_cfg);
+ if (IS_ERR(map))
+ return dev_err_probe(dev, PTR_ERR(map),
+ "can't init regmap mmio region\n");
+
+ /* Populate regmap for the regmap backed clocks */
+ for (i = 0; i < ARRAY_SIZE(a1_cpu_regmaps); i++)
+ a1_cpu_regmaps[i]->map = map;
+
+ for (clkid = 0; clkid < a1_cpu_clks.num; clkid++) {
+ err = devm_clk_hw_register(dev, a1_cpu_clks.hws[clkid]);
+ if (err)
+ return dev_err_probe(dev, err,
+ "clock[%d] registration failed\n",
+ clkid);
+ }
+
+ err = devm_of_clk_add_hw_provider(dev, meson_clk_hw_get, &a1_cpu_clks);
+ if (err)
+ return dev_err_probe(dev, err, "can't add clk hw provider\n");
+
+ return meson_a1_dvfs_setup(pdev);
+}
+
+static const struct of_device_id a1_cpu_clkc_match_table[] = {
+ { .compatible = "amlogic,a1-cpu-clkc", },
+ {}
+};
+MODULE_DEVICE_TABLE(of, a1_cpu_clkc_match_table);
+
+static struct platform_driver a1_cpu_clkc_driver = {
+ .probe = meson_a1_cpu_probe,
+ .driver = {
+ .name = "a1-cpu-clkc",
+ .of_match_table = a1_cpu_clkc_match_table,
+ },
+};
+
+module_platform_driver(a1_cpu_clkc_driver);
+MODULE_AUTHOR("Dmitry Rokosov <ddrokosov@salutedevices.com>");
+MODULE_LICENSE("GPL");
--
2.43.0
prev parent reply other threads:[~2024-05-10 9:09 UTC|newest]
Thread overview: 22+ messages / expand[flat|nested] mbox.gz Atom feed top
2024-05-10 9:08 [PATCH v2 0/7] clk: meson: introduce Amlogic A1 SoC Family CPU clock controller driver Dmitry Rokosov
2024-05-10 9:08 ` [PATCH v2 1/7] clk: meson: introduce 'INIT_ONCE' flag to eliminate init for enabled PLL Dmitry Rokosov
2024-05-13 12:44 ` Jerome Brunet
2024-05-13 21:47 ` Dmitry Rokosov
2024-05-15 13:12 ` Jerome Brunet
2024-05-10 9:08 ` [PATCH v2 2/7] dt-bindings: clock: meson: a1: pll: introduce new syspll bindings Dmitry Rokosov
2024-05-11 13:08 ` Conor Dooley
2024-05-13 9:18 ` Dmitry Rokosov
2024-05-13 15:48 ` Conor Dooley
2024-05-13 18:30 ` Dmitry Rokosov
2024-05-15 13:15 ` Jerome Brunet
2024-05-13 12:04 ` Jerome Brunet
2024-05-13 15:42 ` Conor Dooley
2024-05-10 9:08 ` [PATCH v2 3/7] clk: meson: a1: pll: support 'syspll' general-purpose PLL for CPU clock Dmitry Rokosov
2024-05-13 12:48 ` Jerome Brunet
2024-05-13 21:25 ` Dmitry Rokosov
2024-05-10 9:08 ` [PATCH v2 4/7] dt-bindings: clock: meson: a1: peripherals: support sys_pll_div16 input Dmitry Rokosov
2024-05-11 13:03 ` Conor Dooley
2024-05-13 12:02 ` Jerome Brunet
2024-05-10 9:08 ` [PATCH v2 5/7] clk: meson: a1: peripherals: support 'sys_pll_div16' clock as GEN input Dmitry Rokosov
2024-05-10 9:08 ` [PATCH v2 6/7] dt-bindings: clock: meson: add A1 CPU clock controller bindings Dmitry Rokosov
2024-05-10 9:08 ` Dmitry Rokosov [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20240510090933.19464-8-ddrokosov@salutedevices.com \
--to=ddrokosov@salutedevices.com \
--cc=devicetree@vger.kernel.org \
--cc=jbrunet@baylibre.com \
--cc=jian.hu@amlogic.com \
--cc=kernel@sberdevices.ru \
--cc=khilman@baylibre.com \
--cc=krzysztof.kozlowski+dt@linaro.org \
--cc=linux-amlogic@lists.infradead.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-clk@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=martin.blumenstingl@googlemail.com \
--cc=mturquette@baylibre.com \
--cc=neil.armstrong@linaro.org \
--cc=robh+dt@kernel.org \
--cc=rockosov@gmail.com \
--cc=sboyd@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for read-only IMAP folder(s) and NNTP newsgroup(s).