From: David Lechner <dlechner@baylibre.com>
To: radu.sabau@analog.com, "Lars-Peter Clausen" <lars@metafoo.de>,
"Michael Hennerich" <Michael.Hennerich@analog.com>,
"Jonathan Cameron" <jic23@kernel.org>,
"Nuno Sá" <nuno.sa@analog.com>,
"Andy Shevchenko" <andy@kernel.org>,
"Rob Herring" <robh@kernel.org>,
"Krzysztof Kozlowski" <krzk+dt@kernel.org>,
"Conor Dooley" <conor+dt@kernel.org>,
"Uwe Kleine-König" <ukleinek@kernel.org>,
"Liam Girdwood" <lgirdwood@gmail.com>,
"Mark Brown" <broonie@kernel.org>,
"Linus Walleij" <linusw@kernel.org>,
"Bartosz Golaszewski" <brgl@kernel.org>,
"Philipp Zabel" <p.zabel@pengutronix.de>,
"Jonathan Corbet" <corbet@lwn.net>,
"Shuah Khan" <skhan@linuxfoundation.org>
Cc: linux-iio@vger.kernel.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org, linux-pwm@vger.kernel.org,
linux-gpio@vger.kernel.org, linux-doc@vger.kernel.org
Subject: Re: [PATCH v6 2/4] iio: adc: ad4691: add initial driver for AD4691 family
Date: Sat, 4 Apr 2026 09:25:41 -0500 [thread overview]
Message-ID: <e4ddf44e-3189-4d4a-9184-13b0560195dd@baylibre.com> (raw)
In-Reply-To: <20260403-ad4692-multichannel-sar-adc-driver-v6-2-fa2a01a57c4e@analog.com>
On 4/3/26 6:03 AM, Radu Sabau via B4 Relay wrote:
> From: Radu Sabau <radu.sabau@analog.com>
>
> Add support for the Analog Devices AD4691 family of high-speed,
> low-power multichannel SAR ADCs: AD4691 (16-ch, 500 kSPS),
> AD4692 (16-ch, 1 MSPS), AD4693 (8-ch, 500 kSPS) and
> AD4694 (8-ch, 1 MSPS).
>
> The driver implements a custom regmap layer over raw SPI to handle the
> device's mixed 1/2/3/4-byte register widths and uses the standard IIO
> read_raw/write_raw interface for single-channel reads.
>
> The chip idles in Autonomous Mode so that single-shot read_raw can use
> the internal oscillator without disturbing the hardware configuration.
>
> Three voltage supply domains are managed: avdd (required), vio, and a
> reference supply on either the REF pin (ref-supply, external buffer)
> or the REFIN pin (refin-supply, uses the on-chip reference buffer;
> REFBUF_EN is set accordingly). Hardware reset is performed via
> the reset controller framework; a software reset through SPI_CONFIG_A
> is used as fallback when no hardware reset is available.
>
> Accumulator channel masking for single-shot reads uses ACC_MASK_REG via
> an ADDR_DESCENDING SPI write, which covers both mask bytes in a single
> 16-bit transfer.
>
> Signed-off-by: Radu Sabau <radu.sabau@analog.com>
> ---
This patch looks in good shape. Although I wouldn't mind using
MEGA/MICRO, etc. more in numbers with more than 3 or 4 zeros.
Reviewed-by: David Lechner <dlechner@baylibre.com>
next prev parent reply other threads:[~2026-04-04 14:25 UTC|newest]
Thread overview: 23+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-04-03 11:03 [PATCH v6 0/4] iio: adc: ad4691: add driver for AD4691 multichannel SAR ADC family Radu Sabau via B4 Relay
2026-04-03 11:03 ` [PATCH v6 1/4] dt-bindings: iio: adc: add AD4691 family Radu Sabau via B4 Relay
2026-04-03 11:03 ` [PATCH v6 2/4] iio: adc: ad4691: add initial driver for " Radu Sabau via B4 Relay
2026-04-04 14:25 ` David Lechner [this message]
2026-04-03 11:03 ` [PATCH v6 3/4] iio: adc: ad4691: add triggered buffer support Radu Sabau via B4 Relay
2026-04-04 15:12 ` David Lechner
2026-04-05 8:57 ` Andy Shevchenko
2026-04-06 9:22 ` Sabau, Radu bogdan
2026-04-06 13:39 ` David Lechner
2026-04-03 11:03 ` [PATCH v6 4/4] iio: adc: ad4691: add SPI offload support Radu Sabau via B4 Relay
2026-04-04 15:34 ` David Lechner
2026-04-06 9:34 ` Sabau, Radu bogdan
2026-04-06 13:44 ` David Lechner
2026-04-06 14:16 ` Sabau, Radu bogdan
2026-04-06 15:02 ` David Lechner
2026-04-07 12:38 ` Sabau, Radu bogdan
2026-04-04 15:57 ` David Lechner
2026-04-06 10:39 ` Sabau, Radu bogdan
2026-04-06 11:08 ` Sabau, Radu bogdan
2026-04-06 13:30 ` Sabau, Radu bogdan
2026-04-06 13:56 ` David Lechner
2026-04-06 14:20 ` Sabau, Radu bogdan
2026-04-06 13:53 ` David Lechner
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=e4ddf44e-3189-4d4a-9184-13b0560195dd@baylibre.com \
--to=dlechner@baylibre.com \
--cc=Michael.Hennerich@analog.com \
--cc=andy@kernel.org \
--cc=brgl@kernel.org \
--cc=broonie@kernel.org \
--cc=conor+dt@kernel.org \
--cc=corbet@lwn.net \
--cc=devicetree@vger.kernel.org \
--cc=jic23@kernel.org \
--cc=krzk+dt@kernel.org \
--cc=lars@metafoo.de \
--cc=lgirdwood@gmail.com \
--cc=linusw@kernel.org \
--cc=linux-doc@vger.kernel.org \
--cc=linux-gpio@vger.kernel.org \
--cc=linux-iio@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-pwm@vger.kernel.org \
--cc=nuno.sa@analog.com \
--cc=p.zabel@pengutronix.de \
--cc=radu.sabau@analog.com \
--cc=robh@kernel.org \
--cc=skhan@linuxfoundation.org \
--cc=ukleinek@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for read-only IMAP folder(s) and NNTP newsgroup(s).