From: Javier Carrasco <javier.carrasco.cruz@gmail.com>
To: Jonathan Cameron <jic23@kernel.org>,
Lars-Peter Clausen <lars@metafoo.de>,
Li peiyu <579lpy@gmail.com>, Rob Herring <robh+dt@kernel.org>,
Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
Conor Dooley <conor+dt@kernel.org>
Cc: Jonathan Cameron <Jonathan.Cameron@huawei.com>,
linux-kernel@vger.kernel.org, linux-iio@vger.kernel.org,
devicetree@vger.kernel.org,
Javier Carrasco <javier.carrasco.cruz@gmail.com>,
Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Subject: [PATCH v3 0/3] iio: humidity: hdc3020: add power and reset management
Date: Sun, 03 Mar 2024 22:54:19 +0100 [thread overview]
Message-ID: <20240303-hdc3020-pm-v3-0-48bc02b5241b@gmail.com> (raw)
This series adds power management for the hdc3020 humidity and
temperature sensor as well as control over the reset signal the device
provides.
The hdc3020 carries out measurements automatically, which is not
necessary in low-power modes. Furthermore, if the low-power
configuration turns off the device, proper initialization is required to
account for the setup times and initial status register value.
This device provides an active low reset signal that must be handled if
connected. This signal can be used by the driver to keep the device
under minimal power consumption during low-power modes if the power
supply stays active.
This series uses char-misc-next as basis to include the last additions
to the driver to handle events [1] as well as the fix to include the
entries in the Makefile and Kconfig files [2].
[1] https://lore.kernel.org/linux-iio/20240214085350.19382-1-dima.fedrau@gmail.com/
[2] https://lore.kernel.org/linux-iio/20240121135123.71506-1-jic23@kernel.org/
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
---
Changes in v3:
- Drop unnecessary casting to void in dev_set_drvdata.
- Call devm_add_action_or_reset right after powering on.
- Link to v2: https://lore.kernel.org/r/20240226-hdc3020-pm-v2-0-cec6766086e8@gmail.com
Changes in v2:
- Trigger power off sequence if the power on sequence fails.
- Check return value of hdc3020_power_on() in the probe.
- Remove type casting for void pointer.
- Link to v1: https://lore.kernel.org/r/20240220-hdc3020-pm-v1-0-d8e60dbe79e9@gmail.com
---
Javier Carrasco (3):
iio: humidity: hdc3020: add power management
dt-bindings: iio: humidity: hdc3020: add reset-gpios
iio: humidity: hdc3020: add reset management
.../bindings/iio/humidity/ti,hdc3020.yaml | 5 +
drivers/iio/humidity/hdc3020.c | 111 +++++++++++++++++----
2 files changed, 97 insertions(+), 19 deletions(-)
---
base-commit: d4551c189d6e6a3fcf7f625bd4b273e770fad35a
change-id: 20240217-hdc3020-pm-177983de3cab
Best regards,
--
Javier Carrasco <javier.carrasco.cruz@gmail.com>
next reply other threads:[~2024-03-03 21:54 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2024-03-03 21:54 Javier Carrasco [this message]
2024-03-03 21:54 ` [PATCH v3 1/3] iio: humidity: hdc3020: add power management Javier Carrasco
2024-03-03 21:54 ` [PATCH v3 2/3] dt-bindings: iio: humidity: hdc3020: add reset-gpios Javier Carrasco
2024-03-03 21:54 ` [PATCH v3 3/3] iio: humidity: hdc3020: add reset management Javier Carrasco
2024-03-10 15:24 ` [PATCH v3 0/3] iio: humidity: hdc3020: add power and " Jonathan Cameron
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20240303-hdc3020-pm-v3-0-48bc02b5241b@gmail.com \
--to=javier.carrasco.cruz@gmail.com \
--cc=579lpy@gmail.com \
--cc=Jonathan.Cameron@huawei.com \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=jic23@kernel.org \
--cc=krzysztof.kozlowski+dt@linaro.org \
--cc=krzysztof.kozlowski@linaro.org \
--cc=lars@metafoo.de \
--cc=linux-iio@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for read-only IMAP folder(s) and NNTP newsgroup(s).