From: MIkE <mike@ull.at>
To: linux-laptop@vger.kernel.org
Subject: PROBLEM: uhci-hcd under 2.6* kernel hangs the system
Date: Mon, 26 Jan 2004 13:56:08 +0100 [thread overview]
Message-ID: <20040126135608.3230377e.mike@ull.at> (raw)
[-- Attachment #1: Type: text/plain, Size: 564 bytes --]
when I "modprobe uhci-hcd" the systems hangs after about a minute!
tried this under 2.6.0, 2.6.1-rc1 and 2.6.1
only my good old 2.4.19 works with usb-uhci
Hardware:
Samsung Q10 notebook
00:1d.0 USB Controller: Intel Corp. 82801CA/CAM USB (Hub #1) (rev 02)
00:1d.1 USB Controller: Intel Corp. 82801CA/CAM USB (Hub #2) (rev 02)
00:1d.2 USB Controller: Intel Corp. 82801CA/CAM USB (Hub #3) (rev 02)
the other details as attachement !
anyone mentioned this before ??
mike
--
a woman can fake an orgasm,
but it takes a man
to fake an entire relationship
:-)
[-- Attachment #2: lspci.txt --]
[-- Type: application/octet-stream, Size: 8034 bytes --]
00:00.0 Host bridge: Intel Corp. 82830 830 Chipset Host Bridge (rev 04)
Subsystem: Samsung Electronics Co Ltd: Unknown device c002
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Region 0: Memory at <unassigned> (32-bit, prefetchable)
Capabilities: [40] #09 [0105]
00:02.0 VGA compatible controller: Intel Corp. 82830 CGC [Chipset Graphics Controller] (rev 04) (prog-if 00 [VGA])
Subsystem: Samsung Electronics Co Ltd: Unknown device c002
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 10
Region 0: Memory at e8000000 (32-bit, prefetchable) [size=128M]
Region 1: Memory at e0000000 (32-bit, non-prefetchable) [size=512K]
Capabilities: [d0] Power Management version 1
Flags: PMEClk- DSI+ D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:02.1 Display controller: Intel Corp. 82830 CGC [Chipset Graphics Controller]
Subsystem: Samsung Electronics Co Ltd: Unknown device c002
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (2500ns max)
Region 0: Memory at f0000000 (32-bit, prefetchable) [size=128M]
Region 1: Memory at e0080000 (32-bit, non-prefetchable) [size=512K]
Capabilities: [d0] Power Management version 1
Flags: PMEClk- DSI+ D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:1d.0 USB Controller: Intel Corp. 82801CA/CAM USB (Hub #1) (rev 02) (prog-if 00 [UHCI])
Subsystem: Samsung Electronics Co Ltd: Unknown device c002
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 10
Region 4: I/O ports at 8c80 [size=32]
00:1d.1 USB Controller: Intel Corp. 82801CA/CAM USB (Hub #2) (rev 02) (prog-if 00 [UHCI])
Subsystem: Samsung Electronics Co Ltd: Unknown device c002
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 11
Region 4: I/O ports at 8ca0 [size=32]
00:1d.2 USB Controller: Intel Corp. 82801CA/CAM USB (Hub #3) (rev 02) (prog-if 00 [UHCI])
Subsystem: Samsung Electronics Co Ltd: Unknown device c002
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 11
Region 4: I/O ports at 8cc0 [size=32]
00:1e.0 PCI bridge: Intel Corp. 82801BAM/CAM PCI Bridge (rev 42) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=02, subordinate=03, sec-latency=168
I/O behind bridge: 0000a000-0000afff
Memory behind bridge: e0200000-e02fffff
Prefetchable memory behind bridge: fff00000-000fffff
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
00:1f.0 ISA bridge: Intel Corp. 82801CAM ISA Bridge (LPC) (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:1f.1 IDE interface: Intel Corp. 82801CAM IDE U100 (rev 02) (prog-if 8a [Master SecP PriP])
Subsystem: Samsung Electronics Co Ltd: Unknown device c002
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at <unassigned>
Region 1: I/O ports at <unassigned>
Region 2: I/O ports at <unassigned>
Region 3: I/O ports at <unassigned>
Region 4: I/O ports at 9000 [size=16]
Region 5: Memory at 10000000 (32-bit, non-prefetchable) [size=1K]
00:1f.3 SMBus: Intel Corp. 82801CA/CAM SMBus Controller (rev 02)
Subsystem: Samsung Electronics Co Ltd: Unknown device c002
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 10
Region 4: I/O ports at 8ce0 [size=32]
00:1f.5 Multimedia audio controller: Intel Corp. 82801CA/CAM AC'97 Audio Controller (rev 02)
Subsystem: Samsung Electronics Co Ltd: Unknown device c002
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 10
Region 0: I/O ports at 8400 [size=256]
Region 1: I/O ports at 80c0 [size=64]
00:1f.6 Modem: Intel Corp. 82801CA/CAM AC'97 Modem Controller (rev 02) (prog-if 00 [Generic])
Subsystem: PCTel Inc: Unknown device 4c31
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 10
Region 0: I/O ports at 8800 [size=256]
Region 1: I/O ports at 8c00 [size=128]
02:03.0 CardBus bridge: Ricoh Co Ltd RL5c475 (rev b8)
Subsystem: Samsung Electronics Co Ltd: Unknown device c002
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR+
Latency: 168
Interrupt: pin A routed to IRQ 10
Region 0: Memory at 10001000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=02, secondary=03, subordinate=06, sec-latency=176
Memory window 0: 10400000-107ff000 (prefetchable)
Memory window 1: 10800000-10bff000
I/O window 0: 00004000-000040ff
I/O window 1: 00004400-000044ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt- PostWrite+
16-bit legacy interface ports at 0001
02:03.1 FireWire (IEEE 1394): Ricoh Co Ltd R5C551 IEEE 1394 Controller (prog-if 10 [OHCI])
Subsystem: Samsung Electronics Co Ltd: Unknown device c002
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR+
Latency: 64 (500ns min, 1000ns max)
Interrupt: pin B routed to IRQ 11
Region 0: Memory at e0200000 (32-bit, non-prefetchable) [size=2K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME+
02:05.0 Ethernet controller: 3Com Corporation 3c905C-TX/TX-M [Tornado] (rev 78)
Subsystem: Samsung Electronics Co Ltd: Unknown device c002
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 80 (2500ns min, 2500ns max), cache line size 08
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at a000 [size=128]
Region 1: Memory at e0200800 (32-bit, non-prefetchable) [size=128]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D3 PME-Enable+ DSel=0 DScale=2 PME-
[-- Attachment #3: dmesg.txt --]
[-- Type: application/octet-stream, Size: 8933 bytes --]
Linux version 2.6.1 (root@yoda) (gcc version 3.2.3 20030422 (Gentoo Linux 1.4 3.2.3-r3, propolice)) #1 Sat Jan 17 10:23:02 CET 2004
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009e400 (usable)
BIOS-e820: 000000000009e400 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000c0000 - 00000000000d4000 (reserved)
BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000000f6e0000 (usable)
BIOS-e820: 000000000f6e0000 - 000000000f6f0000 (ACPI data)
BIOS-e820: 000000000f6f0000 - 000000000f700000 (ACPI NVS)
BIOS-e820: 000000000f700000 - 000000000f780000 (usable)
BIOS-e820: 000000000f780000 - 0000000010000000 (reserved)
BIOS-e820: 00000000ff800000 - 00000000ffc00000 (reserved)
BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
247MB LOWMEM available.
On node 0 totalpages: 63360
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 59264 pages, LIFO batch:14
HighMem zone: 0 pages, LIFO batch:1
DMI present.
Building zonelist for node : 0
Kernel command line: root=/dev/hda5 vga=789 pci=usepirqmask quiet
Initializing CPU#0
PID hash table entries: 1024 (order 10: 8192 bytes)
Detected 531.823 MHz processor.
Using tsc for high-res timesource
Console: colour dummy device 80x25
Memory: 247740k/253440k available (1455k kernel code, 4844k reserved, 581k data, 124k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 1048.57 BogoMIPS
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: 0383f9ff 00000000 00000000 00000000
CPU: After vendor identify, caps: 0383f9ff 00000000 00000000 00000000
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 512K
CPU: After all inits, caps: 0383f9ff 00000000 00000000 00000040
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: Intel(R) Pentium(R) III Mobile CPU 800MHz stepping 01
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfd9aa, last bus=3
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
Transparent bridge - 0000:00:1e.0
PCI: Using IRQ router PIIX/ICH [8086/248c] at 0000:00:1f.0
PCI: Found IRQ 11 for device 0000:00:1f.1
PCI: Sharing IRQ 11 with 0000:00:1d.2
PCI: Sharing IRQ 11 with 0000:02:03.1
PCI: Found IRQ 10 for device 0000:02:03.0
PCI: Sharing IRQ 10 with 0000:00:02.0
PCI: Sharing IRQ 10 with 0000:00:1d.0
vesafb: framebuffer at 0xe8000000, mapped to 0xd0000000, size 8000k
vesafb: mode is 800x600x32, linelength=3200, pages=3
vesafb: protected mode interface info at 00ff:44f0
vesafb: scrolling: redraw
vesafb: directcolor: size=8:8:8:8, shift=24:16:8:0
fb0: VESA VGA frame buffer device
SBF: Simple Boot Flag extension found and enabled.
SBF: Setting boot flags 0x1
Machine check exception polling timer started.
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
devfs: v1.22 (20021013) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
Console: switching to colour frame buffer device 100x37
pty: 256 Unix98 ptys configured
Non-volatile memory driver v1.2
hw_random hardware driver 1.0.0 loaded
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing disabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
PCI: Found IRQ 10 for device 0000:00:1f.6
PCI: Sharing IRQ 10 with 0000:00:1f.3
PCI: Sharing IRQ 10 with 0000:00:1f.5
loop: loaded (max 8 devices)
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH3M: IDE controller at PCI slot 0000:00:1f.1
PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
PCI: Found IRQ 11 for device 0000:00:1f.1
PCI: Sharing IRQ 11 with 0000:00:1d.2
PCI: Sharing IRQ 11 with 0000:02:03.1
ICH3M: chipset revision 2
ICH3M: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x9000-0x9007, BIOS settings: hda:DMA, hdb:pio
hda: IC25N020ATCS04-0, ATA DISK drive
Using anticipatory io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: max request size: 128KiB
hda: 39070080 sectors (20003 MB) w/1768KiB Cache, CHS=38760/16/63, UDMA(100)
/dev/ide/host0/bus0/target0/lun0: p1 p2 p3 < p5 p6 p7 >
Console: switching to colour frame buffer device 100x37
mice: PS/2 mouse device common for all mice
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
input: AT Translated Set 2 keyboard on isa0060/serio0
NET: Registered protocol family 2
IP: routing cache hash table of 2048 buckets, 16Kbytes
TCP: Hash tables configured (established 16384 bind 32768)
NET: Registered protocol family 17
PM: Reading pmdisk image.
PM: Resume from disk failed.
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 124k freed
NET: Registered protocol family 1
Adding 512056k swap on /dev/hda2. Priority:-1 extents:1
EXT3 FS on hda5, internal journal
SCSI subsystem initialized
Linux Kernel Card Services
options: [pci] [cardbus] [pm]
PCI: Found IRQ 10 for device 0000:02:03.0
PCI: Sharing IRQ 10 with 0000:00:02.0
PCI: Sharing IRQ 10 with 0000:00:1d.0
Yenta: CardBus bridge found at 0000:02:03.0 [144d:c002]
Yenta: ISA IRQ mask 0x02b8, PCI irq 10
Socket status: 30000006
orinoco.c 0.13e (David Gibson <hermes@gibson.dropbear.id.au> and others)
orinoco_cs.c 0.13e (David Gibson <hermes@gibson.dropbear.id.au> and others)
ohci1394: $Rev: 1087 $ Ben Collins <bcollins@debian.org>
PCI: Found IRQ 11 for device 0000:02:03.1
PCI: Sharing IRQ 11 with 0000:00:1d.2
PCI: Sharing IRQ 11 with 0000:00:1f.1
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[11] MMIO=[e0200000-e02007ff] Max Packet=[2048]
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected an Intel 830M Chipset.
agpgart: Maximum main memory to use for agp memory: 196M
agpgart: Detected 8060K stolen memory.
agpgart: AGP aperture is 128M @ 0xe8000000
mtrr: 0xe8000000,0x8000000 overlaps existing 0xe8000000,0x400000
[drm] Initialized i830 1.3.2 20021108 on minor 0
PCI: Found IRQ 11 for device 0000:02:05.0
PCI: Sharing IRQ 11 with 0000:00:1d.1
3c59x: Donald Becker and others. www.scyld.com/network/vortex.html
0000:02:05.0: 3Com PCI 3c905C Tornado at 0xa000. Vers LK1.1.19
ieee1394: Host added: ID:BUS[0-00:1023] GUID[0000f041040081b1]
Synaptics Touchpad, model: 1
Firmware: 5.9
180 degree mounted touchpad
Sensor: 37
new absolute packet format
Touchpad has extended capability bits
-> multifinger detection
-> palm detection
input: SynPS/2 Synaptics TouchPad on isa0060/serio4
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda7, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
drivers/usb/core/usb.c: registered new driver usbfs
drivers/usb/core/usb.c: registered new driver hub
PCI: Found IRQ 10 for device 0000:00:1f.5
PCI: Sharing IRQ 10 with 0000:00:1f.3
PCI: Sharing IRQ 10 with 0000:00:1f.6
PCI: Setting latency timer of device 0000:00:1f.5 to 64
intel8x0: clocking to 48000
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
cs: memory probe 0x0c0000-0x0fffff: excluding 0xc0000-0xd7fff 0xe0000-0xfffff
eth1: Station identity 001f:0003:0000:0008
eth1: Looks like an Intersil firmware version 0.8.3
eth1: Ad-hoc demo mode supported
eth1: IEEE standard IBSS ad-hoc mode supported
eth1: WEP supported, 104-bit key
eth1: MAC address 00:03:2F:00:B6:22
eth1: Station name "Prism I"
eth1: ready
eth1: index 0x01: Vcc 5.0, irq 10, io 0x0100-0x013f
eth1: This firmware requires an ESSID in IBSS-Ad-Hoc mode.
eth1: New link status: Disconnected (0002)
eth1: This firmware requires an ESSID in IBSS-Ad-Hoc mode.
eth1: This firmware requires an ESSID in IBSS-Ad-Hoc mode.
eth1: New link status: Connected (0001)
inserting floppy driver for 2.6.1
Floppy drive(s): fd0 is 1.44M
FDC 0 is a National Semiconductor PC87306
mtrr: base(0xe8000000) is not aligned on a size(0x300000) boundary
PCI: Found IRQ 10 for device 0000:00:02.0
PCI: Sharing IRQ 10 with 0000:00:1d.0
PCI: Sharing IRQ 10 with 0000:02:03.0
mtrr: 0xe8000000,0x8000000 overlaps existing 0xe8000000,0x400000
atkbd.c: Unknown key released (translated set 2, code 0x7a on isa0060/serio0).
atkbd.c: Unknown key released (translated set 2, code 0x7a on isa0060/serio0).
spurious 8259A interrupt: IRQ7.
[-- Attachment #4: ver_linux.txt --]
[-- Type: application/octet-stream, Size: 977 bytes --]
If some fields are empty or look unusual you may have an old version.
Compare to the current minimal requirements in Documentation/Changes.
Linux yoda 2.6.1 #1 Sat Jan 17 10:23:02 CET 2004 i686 Intel(R) Pentium(R) III Mobile CPU 800MHz GenuineIntel GNU/Linux
Gnu C 3.2.3
Gnu make 3.80
util-linux 2.11z
mount 2.11z
module-init-tools 0.9.12
e2fsprogs 1.34
pcmcia-cs 3.2.5
PPP 2.4.1
Linux C Library 2.3.2
Dynamic linker (ldd) 2.3.2
Procps 3.1.12
Net-tools 1.60
Kbd 1.06
Sh-utils 5.0
Modules Loaded sg floppy snd_intel8x0 snd_ac97_codec snd_mpu401_uart snd_rawmidi snd_pcm_oss snd_pcm snd_page_alloc snd_timer snd_mixer_oss snd soundcore usbcore psmouse 3c59x i830 intel_agp agpgart ohci1394 ieee1394 orinoco_cs ds orinoco hermes yenta_socket pcmcia_core sr_mod scsi_mod cdrom unix
[-- Attachment #5: cpuinfo.txt --]
[-- Type: application/octet-stream, Size: 401 bytes --]
processor : 0
vendor_id : GenuineIntel
cpu family : 6
model : 11
model name : Intel(R) Pentium(R) III Mobile CPU 800MHz
stepping : 1
cpu MHz : 531.823
cache size : 512 KB
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 2
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 sep mtrr pge mca cmov pat pse36 mmx fxsr sse
bogomips : 1048.57
[-- Attachment #6: modules.txt --]
[-- Type: application/octet-stream, Size: 1387 bytes --]
sg 30476 0 - Live 0xd09fd000
floppy 56116 0 - Live 0xd0a11000
snd_intel8x0 29124 0 - Live 0xd09bf000
snd_ac97_codec 52868 1 snd_intel8x0, Live 0xd09ef000
snd_mpu401_uart 6400 1 snd_intel8x0, Live 0xd0977000
snd_rawmidi 20480 1 snd_mpu401_uart, Live 0xd09af000
snd_pcm_oss 49412 0 - Live 0xd09e1000
snd_pcm 87808 2 snd_intel8x0,snd_pcm_oss, Live 0xd09ca000
snd_page_alloc 9348 2 snd_intel8x0,snd_pcm, Live 0xd088d000
snd_timer 22016 1 snd_pcm, Live 0xd097b000
snd_mixer_oss 17408 1 snd_pcm_oss, Live 0xd08b7000
snd 43652 8 snd_intel8x0,snd_ac97_codec,snd_mpu401_uart,snd_rawmidi,snd_pcm_oss,snd_pcm,snd_timer,snd_mixer_oss, Live 0xd0982000
soundcore 7360 1 snd, Live 0xd0891000
usbcore 106964 1 - Live 0xd0993000
psmouse 18828 0 - Live 0xd0894000
3c59x 35752 0 - Live 0xd089a000
i830 71576 2 - Live 0xd08a4000
intel_agp 16280 1 - Live 0xd084a000
agpgart 27208 3 intel_agp, Live 0xd0885000
ohci1394 32512 0 - Live 0xd087c000
ieee1394 210572 1 ohci1394, Live 0xd08bd000
orinoco_cs 6920 1 - Live 0xd0840000
ds 11264 3 orinoco_cs, Live 0xd083c000
orinoco 42756 1 orinoco_cs, Live 0xd0870000
hermes 8064 2 orinoco_cs,orinoco, Live 0xd0839000
yenta_socket 14848 1 - Live 0xd0829000
pcmcia_core 56832 3 orinoco_cs,ds,yenta_socket, Live 0xd0861000
sr_mod 13472 0 - Live 0xd0824000
scsi_mod 65572 2 sg,sr_mod, Live 0xd084f000
cdrom 33440 1 sr_mod, Live 0xd082f000
unix 23948 420 - Live 0xd07dd000
[-- Attachment #7: ioports.txt --]
[-- Type: application/octet-stream, Size: 704 bytes --]
0000-001f : dma1
0020-0021 : pic1
0040-005f : timer
0060-006f : keyboard
0080-008f : dma page reg
00a0-00a1 : pic2
00c0-00df : dma2
00f0-00ff : fpu
0100-013f : orinoco_cs
01f0-01f7 : ide0
03c0-03df : vesafb
03f6-03f6 : ide0
03f8-03ff : serial
0cf8-0cff : PCI conf1
4000-40ff : PCI CardBus #03
4400-44ff : PCI CardBus #03
80c0-80ff : 0000:00:1f.5
80c0-80ff : Intel 82801CA-ICH3 - Controller
8400-84ff : 0000:00:1f.5
8400-84ff : Intel 82801CA-ICH3 - AC'97
8800-88ff : 0000:00:1f.6
8c00-8c7f : 0000:00:1f.6
8c80-8c9f : 0000:00:1d.0
8ca0-8cbf : 0000:00:1d.1
8cc0-8cdf : 0000:00:1d.2
8ce0-8cff : 0000:00:1f.3
9000-900f : 0000:00:1f.1
9000-9007 : ide0
a000-a07f : 0000:02:05.0
a000-a07f : 0000:02:05.0
[-- Attachment #8: interrupts.txt --]
[-- Type: application/octet-stream, Size: 365 bytes --]
CPU0
0: 2373908 XT-PIC timer
1: 11754 XT-PIC i8042
2: 0 XT-PIC cascade
10: 11028 XT-PIC yenta, Intel 82801CA-ICH3, orinoco_cs
11: 4 XT-PIC ohci1394
12: 174027 XT-PIC i8042
14: 9686 XT-PIC ide0
NMI: 0
ERR: 1
[-- Attachment #9: iomem.txt --]
[-- Type: application/octet-stream, Size: 983 bytes --]
00000000-0009e3ff : System RAM
0009e400-0009ffff : reserved
000a0000-000bffff : Video RAM area
000c0000-000d3fff : reserved
000d4000-000d47ff : Extension ROM
000d4800-000d4fff : Extension ROM
000f0000-000fffff : System ROM
00100000-0f6dffff : System RAM
00100000-0026be4d : Kernel code
0026be4e-002fd57f : Kernel data
0f6e0000-0f6effff : ACPI Tables
0f6f0000-0f6fffff : ACPI Non-volatile Storage
0f700000-0f77ffff : System RAM
0f780000-0fffffff : reserved
10000000-100003ff : 0000:00:1f.1
10001000-10001fff : 0000:02:03.0
10001000-10001fff : yenta_socket
10400000-107fffff : PCI CardBus #03
10800000-10bfffff : PCI CardBus #03
60000000-60000fff : card services
e0000000-e007ffff : 0000:00:02.0
e0080000-e00fffff : 0000:00:02.1
e0200000-e02007ff : 0000:02:03.1
e0200000-e02007ff : ohci1394
e0200800-e020087f : 0000:02:05.0
e8000000-efffffff : 0000:00:02.0
e8000000-e87cffff : vesafb
f0000000-f7ffffff : 0000:00:02.1
ff800000-ffbfffff : reserved
fff00000-ffffffff : reserved
[-- Attachment #10: kernel-log-2.4.19.txt --]
[-- Type: application/octet-stream, Size: 2140 bytes --]
Jan 17 11:32:59 localhost kernel: memory : cd6e8160
Jan 17 11:33:58 localhost kernel: usb-uhci.c: $Revision: 1.275 $ time 00:10:23 Nov 3 2003
Jan 17 11:33:58 localhost kernel: usb-uhci.c: High bandwidth mode enabled
Jan 17 11:33:58 localhost kernel: PCI: Found IRQ 10 for device 00:1d.0
Jan 17 11:33:58 localhost kernel: PCI: Sharing IRQ 10 with 00:02.0
Jan 17 11:33:58 localhost kernel: PCI: Sharing IRQ 10 with 02:03.0
Jan 17 11:33:58 localhost kernel: PCI: Setting latency timer of device 00:1d.0 to 64
Jan 17 11:33:58 localhost kernel: usb-uhci.c: USB UHCI at I/O 0x8c80, IRQ 10
Jan 17 11:33:58 localhost kernel: usb-uhci.c: Detected 2 ports
Jan 17 11:33:58 localhost kernel: usb.c: new USB bus registered, assigned bus number 1
Jan 17 11:33:58 localhost kernel: hub.c: USB hub found
Jan 17 11:33:58 localhost kernel: hub.c: 2 ports detected
Jan 17 11:33:58 localhost kernel: PCI: Found IRQ 11 for device 00:1d.1
Jan 17 11:33:58 localhost kernel: PCI: Sharing IRQ 11 with 02:05.0
Jan 17 11:33:58 localhost kernel: PCI: Setting latency timer of device 00:1d.1 to 64
Jan 17 11:33:58 localhost kernel: usb-uhci.c: USB UHCI at I/O 0x8ca0, IRQ 11
Jan 17 11:33:58 localhost kernel: usb-uhci.c: Detected 2 ports
Jan 17 11:33:58 localhost kernel: usb.c: new USB bus registered, assigned bus number 2
Jan 17 11:33:58 localhost kernel: hub.c: USB hub found
Jan 17 11:33:58 localhost kernel: hub.c: 2 ports detected
Jan 17 11:33:58 localhost kernel: PCI: Found IRQ 11 for device 00:1d.2
Jan 17 11:33:58 localhost kernel: PCI: Sharing IRQ 11 with 00:1f.1
Jan 17 11:33:58 localhost kernel: PCI: Sharing IRQ 11 with 02:03.1
Jan 17 11:33:58 localhost kernel: PCI: Setting latency timer of device 00:1d.2 to 64
Jan 17 11:33:58 localhost kernel: usb-uhci.c: USB UHCI at I/O 0x8cc0, IRQ 11
Jan 17 11:33:58 localhost kernel: usb-uhci.c: Detected 2 ports
Jan 17 11:33:58 localhost kernel: usb.c: new USB bus registered, assigned bus number 3
Jan 17 11:33:58 localhost kernel: hub.c: USB hub found
Jan 17 11:33:58 localhost kernel: hub.c: 2 ports detected
Jan 17 11:33:58 localhost kernel: usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
[-- Attachment #11: kernel-log-2.6.0.txt --]
[-- Type: application/octet-stream, Size: 6388 bytes --]
Jan 17 11:22:31 [kernel] Linux version 2.6.0 (root@yoda) (gcc version 3.2.3 20030422 (Gentoo Linux 1.4 3.2.3-r3, propolice)) #4 Mon Dec 29 13:02:07 CET 2003
Jan 17 11:24:04 [kernel] drivers/usb/host/uhci-hcd.c: USB Universal Host Controller Interface driver v2.1
Jan 17 11:24:04 [kernel] PCI: Setting latency timer of device 0000:00:1d.0 to 64
Jan 17 11:24:04 [kernel] uhci_hcd 0000:00:1d.0: irq 10, io base 00008c80
Jan 17 11:24:04 [kernel] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
Jan 17 11:24:04 [kernel] drivers/usb/host/uhci-hcd.c: detected 2 ports
Jan 17 11:24:04 [kernel] uhci_hcd 0000:00:1d.0: root hub device address 1
Jan 17 11:24:04 [kernel] usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
Jan 17 11:24:04 [kernel] drivers/usb/core/message.c: USB device number 1 default language ID 0x409
Jan 17 11:24:04 [kernel] usb usb1: Product: UHCI Host Controller
Jan 17 11:24:04 [kernel] usb usb1: Manufacturer: Linux 2.6.0 uhci_hcd
Jan 17 11:24:04 [kernel] usb usb1: SerialNumber: 0000:00:1d.0
Jan 17 11:24:04 [kernel] drivers/usb/core/usb.c: usb_hotplug
Jan 17 11:24:04 [kernel] usb usb1: registering 1-0:1.0 (config #1, interface 0)
Jan 17 11:24:04 [kernel] drivers/usb/core/usb.c: usb_hotplug
Jan 17 11:24:04 [kernel] hub 1-0:1.0: usb_probe_interface
Jan 17 11:24:04 [kernel] hub 1-0:1.0: usb_probe_interface - got id
Jan 17 11:24:04 [kernel] hub 1-0:1.0: USB hub found
Jan 17 11:24:04 [kernel] hub 1-0:1.0: 2 ports detected
Jan 17 11:24:04 [kernel] hub 1-0:1.0: standalone hub
Jan 17 11:24:04 [kernel] hub 1-0:1.0: ganged power switching
Jan 17 11:24:04 [kernel] hub 1-0:1.0: global over-current protection
Jan 17 11:24:04 [kernel] hub 1-0:1.0: Port indicators are not supported
Jan 17 11:24:04 [kernel] hub 1-0:1.0: power on to power good time: 2ms
Jan 17 11:24:04 [kernel] hub 1-0:1.0: hub controller current requirement: 0mA
Jan 17 11:24:04 [kernel] hub 1-0:1.0: local power source is good
Jan 17 11:24:04 [kernel] hub 1-0:1.0: no over-current condition exists
Jan 17 11:24:04 [kernel] hub 1-0:1.0: enabling power on all ports
Jan 17 11:24:04 [kernel] PCI: Found IRQ 11 for device 0000:00:1d.1
Jan 17 11:24:04 [kernel] PCI: Sharing IRQ 11 with 0000:02:05.0
Jan 17 11:24:04 [kernel] uhci_hcd 0000:00:1d.1: UHCI Host Controller
Jan 17 11:24:04 [kernel] PCI: Setting latency timer of device 0000:00:1d.1 to 64
Jan 17 11:24:04 [kernel] uhci_hcd 0000:00:1d.1: irq 11, io base 00008ca0
Jan 17 11:24:04 [kernel] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
Jan 17 11:24:04 [kernel] drivers/usb/host/uhci-hcd.c: detected 2 ports
Jan 17 11:24:04 [kernel] uhci_hcd 0000:00:1d.1: root hub device address 1
Jan 17 11:24:04 [kernel] usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
Jan 17 11:24:04 [kernel] drivers/usb/core/message.c: USB device number 1 default language ID 0x409
Jan 17 11:24:04 [kernel] usb usb2: Product: UHCI Host Controller
Jan 17 11:24:04 [kernel] usb usb2: Manufacturer: Linux 2.6.0 uhci_hcd
Jan 17 11:24:04 [kernel] usb usb2: SerialNumber: 0000:00:1d.1
Jan 17 11:24:04 [kernel] drivers/usb/core/usb.c: usb_hotplug
Jan 17 11:24:04 [kernel] usb usb2: registering 2-0:1.0 (config #1, interface 0)
Jan 17 11:24:04 [kernel] drivers/usb/core/usb.c: usb_hotplug
Jan 17 11:24:04 [kernel] hub 2-0:1.0: usb_probe_interface
Jan 17 11:24:04 [kernel] hub 2-0:1.0: usb_probe_interface - got id
Jan 17 11:24:04 [kernel] hub 2-0:1.0: USB hub found
Jan 17 11:24:04 [kernel] hub 2-0:1.0: 2 ports detected
Jan 17 11:24:04 [kernel] hub 2-0:1.0: standalone hub
Jan 17 11:24:04 [kernel] hub 2-0:1.0: ganged power switching
Jan 17 11:24:04 [kernel] hub 2-0:1.0: global over-current protection
Jan 17 11:24:04 [kernel] hub 2-0:1.0: Port indicators are not supported
Jan 17 11:24:04 [kernel] hub 2-0:1.0: power on to power good time: 2ms
Jan 17 11:24:04 [kernel] hub 2-0:1.0: hub controller current requirement: 0mA
Jan 17 11:24:04 [kernel] hub 2-0:1.0: local power source is good
Jan 17 11:24:04 [kernel] hub 2-0:1.0: no over-current condition exists
Jan 17 11:24:04 [kernel] hub 2-0:1.0: enabling power on all ports
Jan 17 11:24:04 [kernel] PCI: Found IRQ 11 for device 0000:00:1d.2
Jan 17 11:24:04 [kernel] PCI: Sharing IRQ 11 with 0000:00:1f.1
Jan 17 11:24:04 [kernel] PCI: Sharing IRQ 11 with 0000:02:03.1
Jan 17 11:24:04 [kernel] uhci_hcd 0000:00:1d.2: UHCI Host Controller
Jan 17 11:24:04 [kernel] PCI: Setting latency timer of device 0000:00:1d.2 to 64
Jan 17 11:24:04 [kernel] uhci_hcd 0000:00:1d.2: irq 11, io base 00008cc0
Jan 17 11:24:04 [kernel] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
Jan 17 11:24:04 [kernel] drivers/usb/host/uhci-hcd.c: detected 2 ports
Jan 17 11:24:04 [kernel] uhci_hcd 0000:00:1d.2: root hub device address 1
Jan 17 11:24:04 [kernel] usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1
Jan 17 11:24:04 [kernel] drivers/usb/core/message.c: USB device number 1 default language ID 0x409
Jan 17 11:24:04 [kernel] usb usb3: Product: UHCI Host Controller
Jan 17 11:24:04 [kernel] usb usb3: Manufacturer: Linux 2.6.0 uhci_hcd
Jan 17 11:24:04 [kernel] usb usb3: SerialNumber: 0000:00:1d.2
Jan 17 11:24:04 [kernel] drivers/usb/core/usb.c: usb_hotplug
Jan 17 11:24:04 [kernel] usb usb3: registering 3-0:1.0 (config #1, interface 0)
Jan 17 11:24:04 [kernel] drivers/usb/core/usb.c: usb_hotplug
Jan 17 11:24:05 [kernel] hub 3-0:1.0: usb_probe_interface
Jan 17 11:24:05 [kernel] hub 3-0:1.0: usb_probe_interface - got id
Jan 17 11:24:05 [kernel] hub 3-0:1.0: USB hub found
Jan 17 11:24:05 [kernel] hub 3-0:1.0: 2 ports detected
Jan 17 11:24:05 [kernel] hub 3-0:1.0: standalone hub
Jan 17 11:24:05 [kernel] hub 3-0:1.0: ganged power switching
Jan 17 11:24:05 [kernel] hub 3-0:1.0: global over-current protection
Jan 17 11:24:05 [kernel] hub 3-0:1.0: Port indicators are not supported
Jan 17 11:24:05 [kernel] hub 3-0:1.0: power on to power good time: 2ms
Jan 17 11:24:05 [kernel] hub 3-0:1.0: hub controller current requirement: 0mA
Jan 17 11:24:05 [kernel] hub 3-0:1.0: local power source is good
Jan 17 11:24:05 [kernel] hub 3-0:1.0: no over-current condition exists
Jan 17 11:24:05 [kernel] hub 3-0:1.0: enabling power on all ports
Jan 17 11:24:06 [kernel] drivers/usb/host/uhci-hcd.c: 8c80: suspend_hc
Jan 17 11:24:06 [kernel] drivers/usb/host/uhci-hcd.c: 8ca0: suspend_hc
Jan 17 11:24:07 [kernel] drivers/usb/host/uhci-hcd.c: 8cc0: suspend_hc
[-- Attachment #12: kernel-log-2.6.1.txt --]
[-- Type: application/octet-stream, Size: 6388 bytes --]
Jan 17 10:28:35 [kernel] Linux version 2.6.1 (root@yoda) (gcc version 3.2.3 20030422 (Gentoo Linux 1.4 3.2.3-r3, propolice)) #1 Sat Jan 17 10:23:02 CET 2004
Jan 17 10:30:28 [kernel] drivers/usb/host/uhci-hcd.c: USB Universal Host Controller Interface driver v2.1
Jan 17 10:30:28 [kernel] PCI: Setting latency timer of device 0000:00:1d.0 to 64
Jan 17 10:30:28 [kernel] uhci_hcd 0000:00:1d.0: irq 10, io base 00008c80
Jan 17 10:30:28 [kernel] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
Jan 17 10:30:28 [kernel] drivers/usb/host/uhci-hcd.c: detected 2 ports
Jan 17 10:30:28 [kernel] uhci_hcd 0000:00:1d.0: root hub device address 1
Jan 17 10:30:28 [kernel] usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
Jan 17 10:30:28 [kernel] drivers/usb/core/message.c: USB device number 1 default language ID 0x409
Jan 17 10:30:28 [kernel] usb usb1: Product: UHCI Host Controller
Jan 17 10:30:28 [kernel] usb usb1: Manufacturer: Linux 2.6.1 uhci_hcd
Jan 17 10:30:28 [kernel] usb usb1: SerialNumber: 0000:00:1d.0
Jan 17 10:30:28 [kernel] drivers/usb/core/usb.c: usb_hotplug
Jan 17 10:30:28 [kernel] usb usb1: registering 1-0:1.0 (config #1, interface 0)
Jan 17 10:30:28 [kernel] drivers/usb/core/usb.c: usb_hotplug
Jan 17 10:30:28 [kernel] hub 1-0:1.0: usb_probe_interface
Jan 17 10:30:28 [kernel] hub 1-0:1.0: usb_probe_interface - got id
Jan 17 10:30:28 [kernel] hub 1-0:1.0: USB hub found
Jan 17 10:30:28 [kernel] hub 1-0:1.0: 2 ports detected
Jan 17 10:30:28 [kernel] hub 1-0:1.0: standalone hub
Jan 17 10:30:28 [kernel] hub 1-0:1.0: ganged power switching
Jan 17 10:30:28 [kernel] hub 1-0:1.0: global over-current protection
Jan 17 10:30:28 [kernel] hub 1-0:1.0: Port indicators are not supported
Jan 17 10:30:28 [kernel] hub 1-0:1.0: power on to power good time: 2ms
Jan 17 10:30:28 [kernel] hub 1-0:1.0: hub controller current requirement: 0mA
Jan 17 10:30:28 [kernel] hub 1-0:1.0: local power source is good
Jan 17 10:30:28 [kernel] hub 1-0:1.0: no over-current condition exists
Jan 17 10:30:28 [kernel] hub 1-0:1.0: enabling power on all ports
Jan 17 10:30:28 [kernel] PCI: Found IRQ 11 for device 0000:00:1d.1
Jan 17 10:30:28 [kernel] PCI: Sharing IRQ 11 with 0000:02:05.0
Jan 17 10:30:28 [kernel] uhci_hcd 0000:00:1d.1: UHCI Host Controller
Jan 17 10:30:28 [kernel] PCI: Setting latency timer of device 0000:00:1d.1 to 64
Jan 17 10:30:28 [kernel] uhci_hcd 0000:00:1d.1: irq 11, io base 00008ca0
Jan 17 10:30:28 [kernel] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
Jan 17 10:30:28 [kernel] drivers/usb/host/uhci-hcd.c: detected 2 ports
Jan 17 10:30:28 [kernel] uhci_hcd 0000:00:1d.1: root hub device address 1
Jan 17 10:30:28 [kernel] usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
Jan 17 10:30:28 [kernel] drivers/usb/core/message.c: USB device number 1 default language ID 0x409
Jan 17 10:30:28 [kernel] usb usb2: Product: UHCI Host Controller
Jan 17 10:30:28 [kernel] usb usb2: Manufacturer: Linux 2.6.1 uhci_hcd
Jan 17 10:30:28 [kernel] usb usb2: SerialNumber: 0000:00:1d.1
Jan 17 10:30:28 [kernel] drivers/usb/core/usb.c: usb_hotplug
Jan 17 10:30:28 [kernel] usb usb2: registering 2-0:1.0 (config #1, interface 0)
Jan 17 10:30:28 [kernel] drivers/usb/core/usb.c: usb_hotplug
Jan 17 10:30:28 [kernel] hub 2-0:1.0: usb_probe_interface
Jan 17 10:30:28 [kernel] hub 2-0:1.0: usb_probe_interface - got id
Jan 17 10:30:28 [kernel] hub 2-0:1.0: USB hub found
Jan 17 10:30:28 [kernel] hub 2-0:1.0: 2 ports detected
Jan 17 10:30:28 [kernel] hub 2-0:1.0: standalone hub
Jan 17 10:30:28 [kernel] hub 2-0:1.0: ganged power switching
Jan 17 10:30:28 [kernel] hub 2-0:1.0: global over-current protection
Jan 17 10:30:28 [kernel] hub 2-0:1.0: Port indicators are not supported
Jan 17 10:30:28 [kernel] hub 2-0:1.0: power on to power good time: 2ms
Jan 17 10:30:28 [kernel] hub 2-0:1.0: hub controller current requirement: 0mA
Jan 17 10:30:28 [kernel] hub 2-0:1.0: local power source is good
Jan 17 10:30:28 [kernel] hub 2-0:1.0: no over-current condition exists
Jan 17 10:30:28 [kernel] hub 2-0:1.0: enabling power on all ports
Jan 17 10:30:28 [kernel] PCI: Found IRQ 11 for device 0000:00:1d.2
Jan 17 10:30:28 [kernel] PCI: Sharing IRQ 11 with 0000:00:1f.1
Jan 17 10:30:28 [kernel] PCI: Sharing IRQ 11 with 0000:02:03.1
Jan 17 10:30:28 [kernel] uhci_hcd 0000:00:1d.2: UHCI Host Controller
Jan 17 10:30:29 [kernel] PCI: Setting latency timer of device 0000:00:1d.2 to 64
Jan 17 10:30:29 [kernel] uhci_hcd 0000:00:1d.2: irq 11, io base 00008cc0
Jan 17 10:30:29 [kernel] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
Jan 17 10:30:29 [kernel] drivers/usb/host/uhci-hcd.c: detected 2 ports
Jan 17 10:30:29 [kernel] uhci_hcd 0000:00:1d.2: root hub device address 1
Jan 17 10:30:29 [kernel] usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1
Jan 17 10:30:29 [kernel] drivers/usb/core/message.c: USB device number 1 default language ID 0x409
Jan 17 10:30:29 [kernel] usb usb3: Product: UHCI Host Controller
Jan 17 10:30:29 [kernel] usb usb3: Manufacturer: Linux 2.6.1 uhci_hcd
Jan 17 10:30:29 [kernel] usb usb3: SerialNumber: 0000:00:1d.2
Jan 17 10:30:29 [kernel] drivers/usb/core/usb.c: usb_hotplug
Jan 17 10:30:29 [kernel] usb usb3: registering 3-0:1.0 (config #1, interface 0)
Jan 17 10:30:29 [kernel] drivers/usb/core/usb.c: usb_hotplug
Jan 17 10:30:29 [kernel] hub 3-0:1.0: usb_probe_interface
Jan 17 10:30:29 [kernel] hub 3-0:1.0: usb_probe_interface - got id
Jan 17 10:30:29 [kernel] hub 3-0:1.0: USB hub found
Jan 17 10:30:29 [kernel] hub 3-0:1.0: 2 ports detected
Jan 17 10:30:29 [kernel] hub 3-0:1.0: standalone hub
Jan 17 10:30:29 [kernel] hub 3-0:1.0: ganged power switching
Jan 17 10:30:29 [kernel] hub 3-0:1.0: global over-current protection
Jan 17 10:30:29 [kernel] hub 3-0:1.0: Port indicators are not supported
Jan 17 10:30:29 [kernel] hub 3-0:1.0: power on to power good time: 2ms
Jan 17 10:30:29 [kernel] hub 3-0:1.0: hub controller current requirement: 0mA
Jan 17 10:30:29 [kernel] hub 3-0:1.0: local power source is good
Jan 17 10:30:29 [kernel] hub 3-0:1.0: no over-current condition exists
Jan 17 10:30:29 [kernel] hub 3-0:1.0: enabling power on all ports
Jan 17 10:30:30 [kernel] drivers/usb/host/uhci-hcd.c: 8c80: suspend_hc
Jan 17 10:30:30 [kernel] drivers/usb/host/uhci-hcd.c: 8ca0: suspend_hc
Jan 17 10:30:31 [kernel] drivers/usb/host/uhci-hcd.c: 8cc0: suspend_hc
reply other threads:[~2004-01-26 12:56 UTC|newest]
Thread overview: [no followups] expand[flat|nested] mbox.gz Atom feed
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20040126135608.3230377e.mike@ull.at \
--to=mike@ull.at \
--cc=linux-laptop@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for read-only IMAP folder(s) and NNTP newsgroup(s).