* [PATCH 1/8] rt2x00: Add antenna setting for RT3070/RT3090/RT3390 with RX antenna diversity support
@ 2011-02-20 12:54 Ivo van Doorn
2011-02-20 12:55 ` [PATCH 2/8] rt2x00: Fix rt2800 txpower setting to correct value Ivo van Doorn
0 siblings, 1 reply; 8+ messages in thread
From: Ivo van Doorn @ 2011-02-20 12:54 UTC (permalink / raw
To: John W. Linville; +Cc: users, linux-wireless
From: RA-Jay Hung <Jay_Hung@ralinktech.com>
For RT3070/RT3090/RT3390 with RX antenna diversity support, we must select
default antenna using gpio control way even if we do not turn on
antenna diversity feature.
Seperate the meaning of TX/RX chain and antenna. Some chips use
2x2 TX/RX chain but may have 3 RX antennas or 1x1 TX/RX chain
but may have 2 RX antennas to do antenna diversity.
Signed-off-by: RA-Jay Hung <jay_hung@ralinktech.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
---
drivers/net/wireless/rt2x00/rt2800.h | 3 +
drivers/net/wireless/rt2x00/rt2800lib.c | 74 +++++++++++++++++++++++++++----
drivers/net/wireless/rt2x00/rt2x00.h | 2 +
3 files changed, 70 insertions(+), 9 deletions(-)
diff --git a/drivers/net/wireless/rt2x00/rt2800.h b/drivers/net/wireless/rt2x00/rt2800.h
index ec8159c..ef8f605 100644
--- a/drivers/net/wireless/rt2x00/rt2800.h
+++ b/drivers/net/wireless/rt2x00/rt2800.h
@@ -270,6 +270,7 @@
/*
* GPIO_CTRL_CFG:
+ * GPIOD: GPIO direction, 0: Output, 1: Input
*/
#define GPIO_CTRL_CFG 0x0228
#define GPIO_CTRL_CFG_BIT0 FIELD32(0x00000001)
@@ -281,6 +282,7 @@
#define GPIO_CTRL_CFG_BIT6 FIELD32(0x00000040)
#define GPIO_CTRL_CFG_BIT7 FIELD32(0x00000080)
#define GPIO_CTRL_CFG_BIT8 FIELD32(0x00000100)
+#define GPIO_CTRL_CFG_GPIOD FIELD32(0x00000800)
/*
* MCU_CMD_CFG
@@ -2068,6 +2070,7 @@ struct mac_iveiv_entry {
#define MCU_LED_LED_POLARITY 0x54
#define MCU_RADAR 0x60
#define MCU_BOOT_SIGNAL 0x72
+#define MCU_ANT_SELECT 0X73
#define MCU_BBP_SIGNAL 0x80
#define MCU_POWER_SAVE 0x83
diff --git a/drivers/net/wireless/rt2x00/rt2800lib.c b/drivers/net/wireless/rt2x00/rt2800lib.c
index c9bf074..7f44b97 100644
--- a/drivers/net/wireless/rt2x00/rt2800lib.c
+++ b/drivers/net/wireless/rt2x00/rt2800lib.c
@@ -1368,10 +1368,32 @@ void rt2800_config_erp(struct rt2x00_dev *rt2x00dev, struct rt2x00lib_erp *erp,
}
EXPORT_SYMBOL_GPL(rt2800_config_erp);
+static void rt2800_set_ant_diversity(struct rt2x00_dev *rt2x00dev,
+ enum antenna ant)
+{
+ u32 reg;
+ u8 eesk_pin = (ant == ANTENNA_A) ? 1 : 0;
+ u8 gpio_bit3 = (ant == ANTENNA_A) ? 0 : 1;
+
+ if (rt2x00_is_pci(rt2x00dev)) {
+ rt2800_register_read(rt2x00dev, E2PROM_CSR, ®);
+ rt2x00_set_field32(®, E2PROM_CSR_DATA_CLOCK, eesk_pin);
+ rt2800_register_write(rt2x00dev, E2PROM_CSR, reg);
+ } else if (rt2x00_is_usb(rt2x00dev))
+ rt2800_mcu_request(rt2x00dev, MCU_ANT_SELECT, 0xff,
+ eesk_pin, 0);
+
+ rt2800_register_read(rt2x00dev, GPIO_CTRL_CFG, ®);
+ rt2x00_set_field32(®, GPIO_CTRL_CFG_GPIOD, 0);
+ rt2x00_set_field32(®, GPIO_CTRL_CFG_BIT3, gpio_bit3);
+ rt2800_register_write(rt2x00dev, GPIO_CTRL_CFG, reg);
+}
+
void rt2800_config_ant(struct rt2x00_dev *rt2x00dev, struct antenna_setup *ant)
{
u8 r1;
u8 r3;
+ u16 eeprom;
rt2800_bbp_read(rt2x00dev, 1, &r1);
rt2800_bbp_read(rt2x00dev, 3, &r3);
@@ -1379,7 +1401,7 @@ void rt2800_config_ant(struct rt2x00_dev *rt2x00dev, struct antenna_setup *ant)
/*
* Configure the TX antenna.
*/
- switch ((int)ant->tx) {
+ switch (ant->tx_chain_num) {
case 1:
rt2x00_set_field8(&r1, BBP1_TX_ANTENNA, 0);
break;
@@ -1394,8 +1416,18 @@ void rt2800_config_ant(struct rt2x00_dev *rt2x00dev, struct antenna_setup *ant)
/*
* Configure the RX antenna.
*/
- switch ((int)ant->rx) {
+ switch (ant->rx_chain_num) {
case 1:
+ if (rt2x00_rt(rt2x00dev, RT3070) ||
+ rt2x00_rt(rt2x00dev, RT3090) ||
+ rt2x00_rt(rt2x00dev, RT3390)) {
+ rt2x00_eeprom_read(rt2x00dev,
+ EEPROM_NIC_CONF1, &eeprom);
+ if (rt2x00_get_field16(eeprom,
+ EEPROM_NIC_CONF1_ANT_DIVERSITY))
+ rt2800_set_ant_diversity(rt2x00dev,
+ rt2x00dev->default_ant.rx);
+ }
rt2x00_set_field8(&r3, BBP3_RX_ANTENNA, 0);
break;
case 2:
@@ -1441,13 +1473,13 @@ static void rt2800_config_channel_rf2xxx(struct rt2x00_dev *rt2x00dev,
{
rt2x00_set_field32(&rf->rf4, RF4_FREQ_OFFSET, rt2x00dev->freq_offset);
- if (rt2x00dev->default_ant.tx == 1)
+ if (rt2x00dev->default_ant.tx_chain_num == 1)
rt2x00_set_field32(&rf->rf2, RF2_ANTENNA_TX1, 1);
- if (rt2x00dev->default_ant.rx == 1) {
+ if (rt2x00dev->default_ant.rx_chain_num == 1) {
rt2x00_set_field32(&rf->rf2, RF2_ANTENNA_RX1, 1);
rt2x00_set_field32(&rf->rf2, RF2_ANTENNA_RX2, 1);
- } else if (rt2x00dev->default_ant.rx == 2)
+ } else if (rt2x00dev->default_ant.rx_chain_num == 2)
rt2x00_set_field32(&rf->rf2, RF2_ANTENNA_RX2, 1);
if (rf->channel > 14) {
@@ -1594,13 +1626,13 @@ static void rt2800_config_channel(struct rt2x00_dev *rt2x00dev,
tx_pin = 0;
/* Turn on unused PA or LNA when not using 1T or 1R */
- if (rt2x00dev->default_ant.tx != 1) {
+ if (rt2x00dev->default_ant.tx_chain_num == 2) {
rt2x00_set_field32(&tx_pin, TX_PIN_CFG_PA_PE_A1_EN, 1);
rt2x00_set_field32(&tx_pin, TX_PIN_CFG_PA_PE_G1_EN, 1);
}
/* Turn on unused PA or LNA when not using 1T or 1R */
- if (rt2x00dev->default_ant.rx != 1) {
+ if (rt2x00dev->default_ant.rx_chain_num == 2) {
rt2x00_set_field32(&tx_pin, TX_PIN_CFG_LNA_PE_A1_EN, 1);
rt2x00_set_field32(&tx_pin, TX_PIN_CFG_LNA_PE_G1_EN, 1);
}
@@ -3060,11 +3092,35 @@ int rt2800_init_eeprom(struct rt2x00_dev *rt2x00dev)
/*
* Identify default antenna configuration.
*/
- rt2x00dev->default_ant.tx =
+ rt2x00dev->default_ant.tx_chain_num =
rt2x00_get_field16(eeprom, EEPROM_NIC_CONF0_TXPATH);
- rt2x00dev->default_ant.rx =
+ rt2x00dev->default_ant.rx_chain_num =
rt2x00_get_field16(eeprom, EEPROM_NIC_CONF0_RXPATH);
+ rt2x00_eeprom_read(rt2x00dev, EEPROM_NIC_CONF1, &eeprom);
+
+ if (rt2x00_rt(rt2x00dev, RT3070) ||
+ rt2x00_rt(rt2x00dev, RT3090) ||
+ rt2x00_rt(rt2x00dev, RT3390)) {
+ value = rt2x00_get_field16(eeprom,
+ EEPROM_NIC_CONF1_ANT_DIVERSITY);
+ switch (value) {
+ case 0:
+ case 1:
+ case 2:
+ rt2x00dev->default_ant.tx = ANTENNA_A;
+ rt2x00dev->default_ant.rx = ANTENNA_A;
+ break;
+ case 3:
+ rt2x00dev->default_ant.tx = ANTENNA_A;
+ rt2x00dev->default_ant.rx = ANTENNA_B;
+ break;
+ }
+ } else {
+ rt2x00dev->default_ant.tx = ANTENNA_A;
+ rt2x00dev->default_ant.rx = ANTENNA_A;
+ }
+
/*
* Read frequency offset and RF programming sequence.
*/
diff --git a/drivers/net/wireless/rt2x00/rt2x00.h b/drivers/net/wireless/rt2x00/rt2x00.h
index 39bc2fa..fd28836 100644
--- a/drivers/net/wireless/rt2x00/rt2x00.h
+++ b/drivers/net/wireless/rt2x00/rt2x00.h
@@ -225,6 +225,8 @@ struct channel_info {
struct antenna_setup {
enum antenna rx;
enum antenna tx;
+ u8 rx_chain_num;
+ u8 tx_chain_num;
};
/*
--
1.7.2.3
^ permalink raw reply related [flat|nested] 8+ messages in thread
* [PATCH 2/8] rt2x00: Fix rt2800 txpower setting to correct value
2011-02-20 12:54 [PATCH 1/8] rt2x00: Add antenna setting for RT3070/RT3090/RT3390 with RX antenna diversity support Ivo van Doorn
@ 2011-02-20 12:55 ` Ivo van Doorn
2011-02-20 12:55 ` [PATCH 3/8] rt2x00: Minor optimization for devices with RTS/CTS offload Ivo van Doorn
0 siblings, 1 reply; 8+ messages in thread
From: Ivo van Doorn @ 2011-02-20 12:55 UTC (permalink / raw
To: John W. Linville; +Cc: users, linux-wireless
From: RA-Jay Hung <Jay_Hung@ralinktech.com>
TX_PWR_CFG_* setting need to consider below cases
-compesate 20M/40M tx power delta for 2.4/5GHZ band
-limit maximum EIRP tx power to power_level of
regulatory requirement
Signed-off-by: RA-Jay Hung <jay_hung@ralinktech.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
---
drivers/net/wireless/rt2x00/rt2800.h | 39 ++++--
drivers/net/wireless/rt2x00/rt2800lib.c | 236 ++++++++++++++++++++++--------
drivers/net/wireless/rt2x00/rt2x00.h | 1 +
3 files changed, 199 insertions(+), 77 deletions(-)
diff --git a/drivers/net/wireless/rt2x00/rt2800.h b/drivers/net/wireless/rt2x00/rt2800.h
index ef8f605..457887c 100644
--- a/drivers/net/wireless/rt2x00/rt2800.h
+++ b/drivers/net/wireless/rt2x00/rt2800.h
@@ -1703,11 +1703,14 @@ struct mac_iveiv_entry {
*/
/*
- * BBP 1: TX Antenna & Power
- * POWER: 0 - normal, 1 - drop tx power by 6dBm, 2 - drop tx power by 12dBm,
- * 3 - increase tx power by 6dBm
- */
-#define BBP1_TX_POWER FIELD8(0x07)
+ * BBP 1: TX Antenna & Power Control
+ * POWER_CTRL:
+ * 0 - normal,
+ * 1 - drop tx power by 6dBm,
+ * 2 - drop tx power by 12dBm,
+ * 3 - increase tx power by 6dBm
+ */
+#define BBP1_TX_POWER_CTRL FIELD8(0x07)
#define BBP1_TX_ANTENNA FIELD8(0x18)
/*
@@ -2001,23 +2004,26 @@ struct mac_iveiv_entry {
#define EEPROM_RSSI_A2_LNA_A2 FIELD16(0xff00)
/*
- * EEPROM Maximum TX power values
+ * EEPROM EIRP Maximum TX power values(unit: dbm)
*/
-#define EEPROM_MAX_TX_POWER 0x0027
-#define EEPROM_MAX_TX_POWER_24GHZ FIELD16(0x00ff)
-#define EEPROM_MAX_TX_POWER_5GHZ FIELD16(0xff00)
+#define EEPROM_EIRP_MAX_TX_POWER 0x0027
+#define EEPROM_EIRP_MAX_TX_POWER_2GHZ FIELD16(0x00ff)
+#define EEPROM_EIRP_MAX_TX_POWER_5GHZ FIELD16(0xff00)
/*
* EEPROM TXpower delta: 20MHZ AND 40 MHZ use different power.
* This is delta in 40MHZ.
- * VALUE: Tx Power dalta value (MAX=4)
+ * VALUE: Tx Power dalta value, MAX=4(unit: dbm)
* TYPE: 1: Plus the delta value, 0: minus the delta value
- * TXPOWER: Enable:
+ * ENABLE: enable tx power compensation for 40BW
*/
#define EEPROM_TXPOWER_DELTA 0x0028
-#define EEPROM_TXPOWER_DELTA_VALUE FIELD16(0x003f)
-#define EEPROM_TXPOWER_DELTA_TYPE FIELD16(0x0040)
-#define EEPROM_TXPOWER_DELTA_TXPOWER FIELD16(0x0080)
+#define EEPROM_TXPOWER_DELTA_VALUE_2G FIELD16(0x003f)
+#define EEPROM_TXPOWER_DELTA_TYPE_2G FIELD16(0x0040)
+#define EEPROM_TXPOWER_DELTA_ENABLE_2G FIELD16(0x0080)
+#define EEPROM_TXPOWER_DELTA_VALUE_5G FIELD16(0x3f00)
+#define EEPROM_TXPOWER_DELTA_TYPE_5G FIELD16(0x4000)
+#define EEPROM_TXPOWER_DELTA_ENABLE_5G FIELD16(0x8000)
/*
* EEPROM TXPOWER 802.11BG
@@ -2215,4 +2221,9 @@ struct mac_iveiv_entry {
#define TXPOWER_A_TO_DEV(__txpower) \
clamp_t(char, __txpower, MIN_A_TXPOWER, MAX_A_TXPOWER)
+/*
+ * Board's maximun TX power limitation
+ */
+#define EIRP_MAX_TX_POWER_LIMIT 0x50
+
#endif /* RT2800_H */
diff --git a/drivers/net/wireless/rt2x00/rt2800lib.c b/drivers/net/wireless/rt2x00/rt2800lib.c
index 7f44b97..d23a5d8 100644
--- a/drivers/net/wireless/rt2x00/rt2800lib.c
+++ b/drivers/net/wireless/rt2x00/rt2800lib.c
@@ -1676,30 +1676,116 @@ static void rt2800_config_channel(struct rt2x00_dev *rt2x00dev,
rt2800_register_read(rt2x00dev, CH_BUSY_STA_SEC, ®);
}
+static int rt2800_get_txpower_bw_comp(struct rt2x00_dev *rt2x00dev,
+ enum ieee80211_band band)
+{
+ u16 eeprom;
+ u8 comp_en;
+ u8 comp_type;
+ int comp_value;
+
+ rt2x00_eeprom_read(rt2x00dev, EEPROM_TXPOWER_DELTA, &eeprom);
+
+ if (eeprom == 0xffff)
+ return 0;
+
+ if (band == IEEE80211_BAND_2GHZ) {
+ comp_en = rt2x00_get_field16(eeprom,
+ EEPROM_TXPOWER_DELTA_ENABLE_2G);
+ if (comp_en) {
+ comp_type = rt2x00_get_field16(eeprom,
+ EEPROM_TXPOWER_DELTA_TYPE_2G);
+ comp_value = rt2x00_get_field16(eeprom,
+ EEPROM_TXPOWER_DELTA_VALUE_2G);
+ if (!comp_type)
+ comp_value = -comp_value;
+ }
+ } else {
+ comp_en = rt2x00_get_field16(eeprom,
+ EEPROM_TXPOWER_DELTA_ENABLE_5G);
+ if (comp_en) {
+ comp_type = rt2x00_get_field16(eeprom,
+ EEPROM_TXPOWER_DELTA_TYPE_5G);
+ comp_value = rt2x00_get_field16(eeprom,
+ EEPROM_TXPOWER_DELTA_VALUE_5G);
+ if (!comp_type)
+ comp_value = -comp_value;
+ }
+ }
+
+ return comp_value;
+}
+
+static u8 rt2800_compesate_txpower(struct rt2x00_dev *rt2x00dev,
+ int is_rate_b,
+ enum ieee80211_band band,
+ int power_level,
+ u8 txpower)
+{
+ u32 reg;
+ u16 eeprom;
+ u8 criterion;
+ u8 eirp_txpower;
+ u8 eirp_txpower_criterion;
+ u8 reg_limit;
+ int bw_comp = 0;
+
+ if (!((band == IEEE80211_BAND_5GHZ) && is_rate_b))
+ return txpower;
+
+ if (test_bit(CONFIG_CHANNEL_HT40, &rt2x00dev->flags))
+ bw_comp = rt2800_get_txpower_bw_comp(rt2x00dev, band);
+
+ if (test_bit(CONFIG_SUPPORT_POWER_LIMIT, &rt2x00dev->flags)) {
+ /*
+ * Check if eirp txpower exceed txpower_limit.
+ * We use OFDM 6M as criterion and its eirp txpower
+ * is stored at EEPROM_EIRP_MAX_TX_POWER.
+ * .11b data rate need add additional 4dbm
+ * when calculating eirp txpower.
+ */
+ rt2800_register_read(rt2x00dev, TX_PWR_CFG_0, ®);
+ criterion = rt2x00_get_field32(reg, TX_PWR_CFG_0_6MBS);
+
+ rt2x00_eeprom_read(rt2x00dev,
+ EEPROM_EIRP_MAX_TX_POWER, &eeprom);
+
+ if (band == IEEE80211_BAND_2GHZ)
+ eirp_txpower_criterion = rt2x00_get_field16(eeprom,
+ EEPROM_EIRP_MAX_TX_POWER_2GHZ);
+ else
+ eirp_txpower_criterion = rt2x00_get_field16(eeprom,
+ EEPROM_EIRP_MAX_TX_POWER_5GHZ);
+
+ eirp_txpower = eirp_txpower_criterion + (txpower - criterion) +
+ (is_rate_b ? 4 : 0) + bw_comp;
+
+ reg_limit = (eirp_txpower > power_level) ?
+ (eirp_txpower - power_level) : 0;
+ } else
+ reg_limit = 0;
+
+ return txpower + bw_comp - reg_limit;
+}
+
static void rt2800_config_txpower(struct rt2x00_dev *rt2x00dev,
- const int max_txpower)
+ struct ieee80211_conf *conf)
{
u8 txpower;
- u8 max_value = (u8)max_txpower;
u16 eeprom;
- int i;
+ int i, is_rate_b;
u32 reg;
u8 r1;
u32 offset;
+ enum ieee80211_band band = conf->channel->band;
+ int power_level = conf->power_level;
/*
- * set to normal tx power mode: +/- 0dBm
+ * set to normal bbp tx power control mode: +/- 0dBm
*/
rt2800_bbp_read(rt2x00dev, 1, &r1);
- rt2x00_set_field8(&r1, BBP1_TX_POWER, 0);
+ rt2x00_set_field8(&r1, BBP1_TX_POWER_CTRL, 0);
rt2800_bbp_write(rt2x00dev, 1, r1);
-
- /*
- * The eeprom contains the tx power values for each rate. These
- * values map to 100% tx power. Each 16bit word contains four tx
- * power values and the order is the same as used in the TX_PWR_CFG
- * registers.
- */
offset = TX_PWR_CFG_0;
for (i = 0; i < EEPROM_TXPOWER_BYRATE_SIZE; i += 2) {
@@ -1713,73 +1799,99 @@ static void rt2800_config_txpower(struct rt2x00_dev *rt2x00dev,
rt2x00_eeprom_read(rt2x00dev, EEPROM_TXPOWER_BYRATE + i,
&eeprom);
- /* TX_PWR_CFG_0: 1MBS, TX_PWR_CFG_1: 24MBS,
+ is_rate_b = i ? 0 : 1;
+ /*
+ * TX_PWR_CFG_0: 1MBS, TX_PWR_CFG_1: 24MBS,
* TX_PWR_CFG_2: MCS4, TX_PWR_CFG_3: MCS12,
- * TX_PWR_CFG_4: unknown */
+ * TX_PWR_CFG_4: unknown
+ */
txpower = rt2x00_get_field16(eeprom,
EEPROM_TXPOWER_BYRATE_RATE0);
- rt2x00_set_field32(®, TX_PWR_CFG_RATE0,
- min(txpower, max_value));
+ txpower = rt2800_compesate_txpower(rt2x00dev, is_rate_b, band,
+ power_level, txpower);
+ rt2x00_set_field32(®, TX_PWR_CFG_RATE0, txpower);
- /* TX_PWR_CFG_0: 2MBS, TX_PWR_CFG_1: 36MBS,
+ /*
+ * TX_PWR_CFG_0: 2MBS, TX_PWR_CFG_1: 36MBS,
* TX_PWR_CFG_2: MCS5, TX_PWR_CFG_3: MCS13,
- * TX_PWR_CFG_4: unknown */
+ * TX_PWR_CFG_4: unknown
+ */
txpower = rt2x00_get_field16(eeprom,
EEPROM_TXPOWER_BYRATE_RATE1);
- rt2x00_set_field32(®, TX_PWR_CFG_RATE1,
- min(txpower, max_value));
+ txpower = rt2800_compesate_txpower(rt2x00dev, is_rate_b, band,
+ power_level, txpower);
+ rt2x00_set_field32(®, TX_PWR_CFG_RATE1, txpower);
- /* TX_PWR_CFG_0: 55MBS, TX_PWR_CFG_1: 48MBS,
+ /*
+ * TX_PWR_CFG_0: 5.5MBS, TX_PWR_CFG_1: 48MBS,
* TX_PWR_CFG_2: MCS6, TX_PWR_CFG_3: MCS14,
- * TX_PWR_CFG_4: unknown */
+ * TX_PWR_CFG_4: unknown
+ */
txpower = rt2x00_get_field16(eeprom,
EEPROM_TXPOWER_BYRATE_RATE2);
- rt2x00_set_field32(®, TX_PWR_CFG_RATE2,
- min(txpower, max_value));
+ txpower = rt2800_compesate_txpower(rt2x00dev, is_rate_b, band,
+ power_level, txpower);
+ rt2x00_set_field32(®, TX_PWR_CFG_RATE2, txpower);
- /* TX_PWR_CFG_0: 11MBS, TX_PWR_CFG_1: 54MBS,
+ /*
+ * TX_PWR_CFG_0: 11MBS, TX_PWR_CFG_1: 54MBS,
* TX_PWR_CFG_2: MCS7, TX_PWR_CFG_3: MCS15,
- * TX_PWR_CFG_4: unknown */
+ * TX_PWR_CFG_4: unknown
+ */
txpower = rt2x00_get_field16(eeprom,
EEPROM_TXPOWER_BYRATE_RATE3);
- rt2x00_set_field32(®, TX_PWR_CFG_RATE3,
- min(txpower, max_value));
+ txpower = rt2800_compesate_txpower(rt2x00dev, is_rate_b, band,
+ power_level, txpower);
+ rt2x00_set_field32(®, TX_PWR_CFG_RATE3, txpower);
/* read the next four txpower values */
rt2x00_eeprom_read(rt2x00dev, EEPROM_TXPOWER_BYRATE + i + 1,
&eeprom);
- /* TX_PWR_CFG_0: 6MBS, TX_PWR_CFG_1: MCS0,
+ is_rate_b = 0;
+ /*
+ * TX_PWR_CFG_0: 6MBS, TX_PWR_CFG_1: MCS0,
* TX_PWR_CFG_2: MCS8, TX_PWR_CFG_3: unknown,
- * TX_PWR_CFG_4: unknown */
+ * TX_PWR_CFG_4: unknown
+ */
txpower = rt2x00_get_field16(eeprom,
EEPROM_TXPOWER_BYRATE_RATE0);
- rt2x00_set_field32(®, TX_PWR_CFG_RATE4,
- min(txpower, max_value));
+ txpower = rt2800_compesate_txpower(rt2x00dev, is_rate_b, band,
+ power_level, txpower);
+ rt2x00_set_field32(®, TX_PWR_CFG_RATE4, txpower);
- /* TX_PWR_CFG_0: 9MBS, TX_PWR_CFG_1: MCS1,
+ /*
+ * TX_PWR_CFG_0: 9MBS, TX_PWR_CFG_1: MCS1,
* TX_PWR_CFG_2: MCS9, TX_PWR_CFG_3: unknown,
- * TX_PWR_CFG_4: unknown */
+ * TX_PWR_CFG_4: unknown
+ */
txpower = rt2x00_get_field16(eeprom,
EEPROM_TXPOWER_BYRATE_RATE1);
- rt2x00_set_field32(®, TX_PWR_CFG_RATE5,
- min(txpower, max_value));
+ txpower = rt2800_compesate_txpower(rt2x00dev, is_rate_b, band,
+ power_level, txpower);
+ rt2x00_set_field32(®, TX_PWR_CFG_RATE5, txpower);
- /* TX_PWR_CFG_0: 12MBS, TX_PWR_CFG_1: MCS2,
+ /*
+ * TX_PWR_CFG_0: 12MBS, TX_PWR_CFG_1: MCS2,
* TX_PWR_CFG_2: MCS10, TX_PWR_CFG_3: unknown,
- * TX_PWR_CFG_4: unknown */
+ * TX_PWR_CFG_4: unknown
+ */
txpower = rt2x00_get_field16(eeprom,
EEPROM_TXPOWER_BYRATE_RATE2);
- rt2x00_set_field32(®, TX_PWR_CFG_RATE6,
- min(txpower, max_value));
+ txpower = rt2800_compesate_txpower(rt2x00dev, is_rate_b, band,
+ power_level, txpower);
+ rt2x00_set_field32(®, TX_PWR_CFG_RATE6, txpower);
- /* TX_PWR_CFG_0: 18MBS, TX_PWR_CFG_1: MCS3,
+ /*
+ * TX_PWR_CFG_0: 18MBS, TX_PWR_CFG_1: MCS3,
* TX_PWR_CFG_2: MCS11, TX_PWR_CFG_3: unknown,
- * TX_PWR_CFG_4: unknown */
+ * TX_PWR_CFG_4: unknown
+ */
txpower = rt2x00_get_field16(eeprom,
EEPROM_TXPOWER_BYRATE_RATE3);
- rt2x00_set_field32(®, TX_PWR_CFG_RATE7,
- min(txpower, max_value));
+ txpower = rt2800_compesate_txpower(rt2x00dev, is_rate_b, band,
+ power_level, txpower);
+ rt2x00_set_field32(®, TX_PWR_CFG_RATE7, txpower);
rt2800_register_write(rt2x00dev, offset, reg);
@@ -1838,11 +1950,13 @@ void rt2800_config(struct rt2x00_dev *rt2x00dev,
/* Always recalculate LNA gain before changing configuration */
rt2800_config_lna_gain(rt2x00dev, libconf);
- if (flags & IEEE80211_CONF_CHANGE_CHANNEL)
+ if (flags & IEEE80211_CONF_CHANGE_CHANNEL) {
rt2800_config_channel(rt2x00dev, libconf->conf,
&libconf->rf, &libconf->channel);
+ rt2800_config_txpower(rt2x00dev, libconf->conf);
+ }
if (flags & IEEE80211_CONF_CHANGE_POWER)
- rt2800_config_txpower(rt2x00dev, libconf->conf->power_level);
+ rt2800_config_txpower(rt2x00dev, libconf->conf);
if (flags & IEEE80211_CONF_CHANGE_RETRY_LIMITS)
rt2800_config_retry_limit(rt2x00dev, libconf);
if (flags & IEEE80211_CONF_CHANGE_PS)
@@ -3032,13 +3146,6 @@ int rt2800_validate_eeprom(struct rt2x00_dev *rt2x00dev)
default_lna_gain);
rt2x00_eeprom_write(rt2x00dev, EEPROM_RSSI_A2, word);
- rt2x00_eeprom_read(rt2x00dev, EEPROM_MAX_TX_POWER, &word);
- if (rt2x00_get_field16(word, EEPROM_MAX_TX_POWER_24GHZ) == 0xff)
- rt2x00_set_field16(&word, EEPROM_MAX_TX_POWER_24GHZ, MAX_G_TXPOWER);
- if (rt2x00_get_field16(word, EEPROM_MAX_TX_POWER_5GHZ) == 0xff)
- rt2x00_set_field16(&word, EEPROM_MAX_TX_POWER_5GHZ, MAX_A_TXPOWER);
- rt2x00_eeprom_write(rt2x00dev, EEPROM_MAX_TX_POWER, word);
-
return 0;
}
EXPORT_SYMBOL_GPL(rt2800_validate_eeprom);
@@ -3154,6 +3261,15 @@ int rt2800_init_eeprom(struct rt2x00_dev *rt2x00dev)
rt2x00_eeprom_read(rt2x00dev, EEPROM_FREQ, &rt2x00dev->led_mcu_reg);
#endif /* CONFIG_RT2X00_LIB_LEDS */
+ /*
+ * Check if support EIRP tx power limit feature.
+ */
+ rt2x00_eeprom_read(rt2x00dev, EEPROM_EIRP_MAX_TX_POWER, &eeprom);
+
+ if (rt2x00_get_field16(eeprom, EEPROM_EIRP_MAX_TX_POWER_2GHZ) <
+ EIRP_MAX_TX_POWER_LIMIT)
+ __set_bit(CONFIG_SUPPORT_POWER_LIMIT, &rt2x00dev->flags);
+
return 0;
}
EXPORT_SYMBOL_GPL(rt2800_init_eeprom);
@@ -3306,7 +3422,6 @@ int rt2800_probe_hw_mode(struct rt2x00_dev *rt2x00dev)
char *default_power1;
char *default_power2;
unsigned int i;
- unsigned short max_power;
u16 eeprom;
/*
@@ -3431,26 +3546,21 @@ int rt2800_probe_hw_mode(struct rt2x00_dev *rt2x00dev)
spec->channels_info = info;
- rt2x00_eeprom_read(rt2x00dev, EEPROM_MAX_TX_POWER, &eeprom);
- max_power = rt2x00_get_field16(eeprom, EEPROM_MAX_TX_POWER_24GHZ);
default_power1 = rt2x00_eeprom_addr(rt2x00dev, EEPROM_TXPOWER_BG1);
default_power2 = rt2x00_eeprom_addr(rt2x00dev, EEPROM_TXPOWER_BG2);
for (i = 0; i < 14; i++) {
- info[i].max_power = max_power;
- info[i].default_power1 = TXPOWER_G_FROM_DEV(default_power1[i]);
- info[i].default_power2 = TXPOWER_G_FROM_DEV(default_power2[i]);
+ info[i].default_power1 = default_power1[i];
+ info[i].default_power2 = default_power2[i];
}
if (spec->num_channels > 14) {
- max_power = rt2x00_get_field16(eeprom, EEPROM_MAX_TX_POWER_5GHZ);
default_power1 = rt2x00_eeprom_addr(rt2x00dev, EEPROM_TXPOWER_A1);
default_power2 = rt2x00_eeprom_addr(rt2x00dev, EEPROM_TXPOWER_A2);
for (i = 14; i < spec->num_channels; i++) {
- info[i].max_power = max_power;
- info[i].default_power1 = TXPOWER_A_FROM_DEV(default_power1[i]);
- info[i].default_power2 = TXPOWER_A_FROM_DEV(default_power2[i]);
+ info[i].default_power1 = default_power1[i];
+ info[i].default_power2 = default_power2[i];
}
}
diff --git a/drivers/net/wireless/rt2x00/rt2x00.h b/drivers/net/wireless/rt2x00/rt2x00.h
index fd28836..64c6ef5 100644
--- a/drivers/net/wireless/rt2x00/rt2x00.h
+++ b/drivers/net/wireless/rt2x00/rt2x00.h
@@ -667,6 +667,7 @@ enum rt2x00_flags {
*/
CONFIG_SUPPORT_HW_BUTTON,
CONFIG_SUPPORT_HW_CRYPTO,
+ CONFIG_SUPPORT_POWER_LIMIT,
DRIVER_SUPPORT_CONTROL_FILTERS,
DRIVER_SUPPORT_CONTROL_FILTER_PSPOLL,
DRIVER_SUPPORT_PRE_TBTT_INTERRUPT,
--
1.7.2.3
^ permalink raw reply related [flat|nested] 8+ messages in thread
* [PATCH 3/8] rt2x00: Minor optimization for devices with RTS/CTS offload
2011-02-20 12:55 ` [PATCH 2/8] rt2x00: Fix rt2800 txpower setting to correct value Ivo van Doorn
@ 2011-02-20 12:55 ` Ivo van Doorn
2011-02-20 12:56 ` [PATCH 4/8] Revert "rt2x00 : avoid timestamp for monitor injected frame." Ivo van Doorn
0 siblings, 1 reply; 8+ messages in thread
From: Ivo van Doorn @ 2011-02-20 12:55 UTC (permalink / raw
To: John W. Linville; +Cc: users, linux-wireless
From: Helmut Schaa <helmut.schaa@googlemail.com>
Only devices that don't have RTS/CTS offload need to check for
IEEE80211_TX_RC_USE_RTS_CTS and IEEE80211_TX_RC_USE_CTS_PROTECT.
By swapping both conditions we keep the same number of needed conditionals
for devices without RTS/CTS offload but save one conditional on devices
with RTS/CTS offload.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
---
drivers/net/wireless/rt2x00/rt2x00mac.c | 6 +++---
1 files changed, 3 insertions(+), 3 deletions(-)
diff --git a/drivers/net/wireless/rt2x00/rt2x00mac.c b/drivers/net/wireless/rt2x00/rt2x00mac.c
index 6a66021..1b3edef 100644
--- a/drivers/net/wireless/rt2x00/rt2x00mac.c
+++ b/drivers/net/wireless/rt2x00/rt2x00mac.c
@@ -139,9 +139,9 @@ int rt2x00mac_tx(struct ieee80211_hw *hw, struct sk_buff *skb)
* either RTS or CTS-to-self frame and handles everything
* inside the hardware.
*/
- if ((tx_info->control.rates[0].flags & (IEEE80211_TX_RC_USE_RTS_CTS |
- IEEE80211_TX_RC_USE_CTS_PROTECT)) &&
- !rt2x00dev->ops->hw->set_rts_threshold) {
+ if (!rt2x00dev->ops->hw->set_rts_threshold &&
+ (tx_info->control.rates[0].flags & (IEEE80211_TX_RC_USE_RTS_CTS |
+ IEEE80211_TX_RC_USE_CTS_PROTECT))) {
if (rt2x00queue_available(queue) <= 1)
goto exit_fail;
--
1.7.2.3
^ permalink raw reply related [flat|nested] 8+ messages in thread
* [PATCH 4/8] Revert "rt2x00 : avoid timestamp for monitor injected frame."
2011-02-20 12:55 ` [PATCH 3/8] rt2x00: Minor optimization for devices with RTS/CTS offload Ivo van Doorn
@ 2011-02-20 12:56 ` Ivo van Doorn
2011-02-20 12:56 ` [PATCH 5/8] rt2x00: Remove superfluos empty line Ivo van Doorn
0 siblings, 1 reply; 8+ messages in thread
From: Ivo van Doorn @ 2011-02-20 12:56 UTC (permalink / raw
To: John W. Linville; +Cc: users, linux-wireless
From: Helmut Schaa <helmut.schaa@googlemail.com>
This reverts commit e81e0aef32bfa7f593b14479b9c7eaa7196798ac "rt2x00 : avoid
timestamp for monitor injected frame." as it breaks proper timestamp insertion
into probe responses injected by hostapd for example.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Cc: Benoit PAPILLAULT <benoit.papillault@free.fr>
Cc: Alban Browaeys <prahal@yahoo.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
---
drivers/net/wireless/rt2x00/rt2x00queue.c | 9 +++------
1 files changed, 3 insertions(+), 6 deletions(-)
diff --git a/drivers/net/wireless/rt2x00/rt2x00queue.c b/drivers/net/wireless/rt2x00/rt2x00queue.c
index fa17c83..bf9bba3 100644
--- a/drivers/net/wireless/rt2x00/rt2x00queue.c
+++ b/drivers/net/wireless/rt2x00/rt2x00queue.c
@@ -365,13 +365,10 @@ static void rt2x00queue_create_tx_descriptor(struct queue_entry *entry,
/*
* Beacons and probe responses require the tsf timestamp
- * to be inserted into the frame, except for a frame that has been injected
- * through a monitor interface. This latter is needed for testing a
- * monitor interface.
+ * to be inserted into the frame.
*/
- if ((ieee80211_is_beacon(hdr->frame_control) ||
- ieee80211_is_probe_resp(hdr->frame_control)) &&
- (!(tx_info->flags & IEEE80211_TX_CTL_INJECTED)))
+ if (ieee80211_is_beacon(hdr->frame_control) ||
+ ieee80211_is_probe_resp(hdr->frame_control))
__set_bit(ENTRY_TXD_REQ_TIMESTAMP, &txdesc->flags);
/*
--
1.7.2.3
^ permalink raw reply related [flat|nested] 8+ messages in thread
* [PATCH 5/8] rt2x00: Remove superfluos empty line
2011-02-20 12:56 ` [PATCH 4/8] Revert "rt2x00 : avoid timestamp for monitor injected frame." Ivo van Doorn
@ 2011-02-20 12:56 ` Ivo van Doorn
2011-02-20 12:56 ` [PATCH 6/8] rt2x00: Add/Modify protection related register definitions Ivo van Doorn
0 siblings, 1 reply; 8+ messages in thread
From: Ivo van Doorn @ 2011-02-20 12:56 UTC (permalink / raw
To: John W. Linville; +Cc: users, linux-wireless
From: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
---
drivers/net/wireless/rt2x00/rt2x00ht.c | 1 -
1 files changed, 0 insertions(+), 1 deletions(-)
diff --git a/drivers/net/wireless/rt2x00/rt2x00ht.c b/drivers/net/wireless/rt2x00/rt2x00ht.c
index b7ad46e..03d9579 100644
--- a/drivers/net/wireless/rt2x00/rt2x00ht.c
+++ b/drivers/net/wireless/rt2x00/rt2x00ht.c
@@ -69,7 +69,6 @@ void rt2x00ht_create_tx_descriptor(struct queue_entry *entry,
txdesc->mcs |= 0x08;
}
-
/*
* This frame is eligible for an AMPDU, however, don't aggregate
* frames that are intended to probe a specific tx rate.
--
1.7.2.3
^ permalink raw reply related [flat|nested] 8+ messages in thread
* [PATCH 6/8] rt2x00: Add/Modify protection related register definitions
2011-02-20 12:56 ` [PATCH 5/8] rt2x00: Remove superfluos empty line Ivo van Doorn
@ 2011-02-20 12:56 ` Ivo van Doorn
2011-02-20 12:57 ` [PATCH 7/8] rt2x00: Add/Modify the GPIO register definition Ivo van Doorn
0 siblings, 1 reply; 8+ messages in thread
From: Ivo van Doorn @ 2011-02-20 12:56 UTC (permalink / raw
To: John W. Linville; +Cc: users, linux-wireless
From: Shiang Tu <shiang_tu@ralinktech.com>
Make the definition of protection related registers more precisely
Signed-off-by: Shiang Tu <shiang_tu@ralinktech.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
---
drivers/net/wireless/rt2x00/rt2800.h | 22 ++++++++++++++--------
drivers/net/wireless/rt2x00/rt2800lib.c | 12 ++++++------
2 files changed, 20 insertions(+), 14 deletions(-)
diff --git a/drivers/net/wireless/rt2x00/rt2800.h b/drivers/net/wireless/rt2x00/rt2800.h
index 457887c..d3a693b 100644
--- a/drivers/net/wireless/rt2x00/rt2800.h
+++ b/drivers/net/wireless/rt2x00/rt2800.h
@@ -1138,8 +1138,8 @@
* PROTECT_RATE: Protection control frame rate for CCK TX(RTS/CTS/CFEnd)
* PROTECT_CTRL: Protection control frame type for CCK TX
* 0:none, 1:RTS/CTS, 2:CTS-to-self
- * PROTECT_NAV: TXOP protection type for CCK TX
- * 0:none, 1:ShortNAVprotect, 2:LongNAVProtect
+ * PROTECT_NAV_SHORT: TXOP protection type for CCK TX with short NAV
+ * PROTECT_NAV_LONG: TXOP protection type for CCK TX with long NAV
* TX_OP_ALLOW_CCK: CCK TXOP allowance, 0:disallow
* TX_OP_ALLOW_OFDM: CCK TXOP allowance, 0:disallow
* TX_OP_ALLOW_MM20: CCK TXOP allowance, 0:disallow
@@ -1151,7 +1151,8 @@
#define CCK_PROT_CFG 0x1364
#define CCK_PROT_CFG_PROTECT_RATE FIELD32(0x0000ffff)
#define CCK_PROT_CFG_PROTECT_CTRL FIELD32(0x00030000)
-#define CCK_PROT_CFG_PROTECT_NAV FIELD32(0x000c0000)
+#define CCK_PROT_CFG_PROTECT_NAV_SHORT FIELD32(0x00040000)
+#define CCK_PROT_CFG_PROTECT_NAV_LONG FIELD32(0x00080000)
#define CCK_PROT_CFG_TX_OP_ALLOW_CCK FIELD32(0x00100000)
#define CCK_PROT_CFG_TX_OP_ALLOW_OFDM FIELD32(0x00200000)
#define CCK_PROT_CFG_TX_OP_ALLOW_MM20 FIELD32(0x00400000)
@@ -1166,7 +1167,8 @@
#define OFDM_PROT_CFG 0x1368
#define OFDM_PROT_CFG_PROTECT_RATE FIELD32(0x0000ffff)
#define OFDM_PROT_CFG_PROTECT_CTRL FIELD32(0x00030000)
-#define OFDM_PROT_CFG_PROTECT_NAV FIELD32(0x000c0000)
+#define OFDM_PROT_CFG_PROTECT_NAV_SHORT FIELD32(0x00040000)
+#define OFDM_PROT_CFG_PROTECT_NAV_LONG FIELD32(0x00080000)
#define OFDM_PROT_CFG_TX_OP_ALLOW_CCK FIELD32(0x00100000)
#define OFDM_PROT_CFG_TX_OP_ALLOW_OFDM FIELD32(0x00200000)
#define OFDM_PROT_CFG_TX_OP_ALLOW_MM20 FIELD32(0x00400000)
@@ -1181,7 +1183,8 @@
#define MM20_PROT_CFG 0x136c
#define MM20_PROT_CFG_PROTECT_RATE FIELD32(0x0000ffff)
#define MM20_PROT_CFG_PROTECT_CTRL FIELD32(0x00030000)
-#define MM20_PROT_CFG_PROTECT_NAV FIELD32(0x000c0000)
+#define MM20_PROT_CFG_PROTECT_NAV_SHORT FIELD32(0x00040000)
+#define MM20_PROT_CFG_PROTECT_NAV_LONG FIELD32(0x00080000)
#define MM20_PROT_CFG_TX_OP_ALLOW_CCK FIELD32(0x00100000)
#define MM20_PROT_CFG_TX_OP_ALLOW_OFDM FIELD32(0x00200000)
#define MM20_PROT_CFG_TX_OP_ALLOW_MM20 FIELD32(0x00400000)
@@ -1196,7 +1199,8 @@
#define MM40_PROT_CFG 0x1370
#define MM40_PROT_CFG_PROTECT_RATE FIELD32(0x0000ffff)
#define MM40_PROT_CFG_PROTECT_CTRL FIELD32(0x00030000)
-#define MM40_PROT_CFG_PROTECT_NAV FIELD32(0x000c0000)
+#define MM40_PROT_CFG_PROTECT_NAV_SHORT FIELD32(0x00040000)
+#define MM40_PROT_CFG_PROTECT_NAV_LONG FIELD32(0x00080000)
#define MM40_PROT_CFG_TX_OP_ALLOW_CCK FIELD32(0x00100000)
#define MM40_PROT_CFG_TX_OP_ALLOW_OFDM FIELD32(0x00200000)
#define MM40_PROT_CFG_TX_OP_ALLOW_MM20 FIELD32(0x00400000)
@@ -1211,7 +1215,8 @@
#define GF20_PROT_CFG 0x1374
#define GF20_PROT_CFG_PROTECT_RATE FIELD32(0x0000ffff)
#define GF20_PROT_CFG_PROTECT_CTRL FIELD32(0x00030000)
-#define GF20_PROT_CFG_PROTECT_NAV FIELD32(0x000c0000)
+#define GF20_PROT_CFG_PROTECT_NAV_SHORT FIELD32(0x00040000)
+#define GF20_PROT_CFG_PROTECT_NAV_LONG FIELD32(0x00080000)
#define GF20_PROT_CFG_TX_OP_ALLOW_CCK FIELD32(0x00100000)
#define GF20_PROT_CFG_TX_OP_ALLOW_OFDM FIELD32(0x00200000)
#define GF20_PROT_CFG_TX_OP_ALLOW_MM20 FIELD32(0x00400000)
@@ -1226,7 +1231,8 @@
#define GF40_PROT_CFG 0x1378
#define GF40_PROT_CFG_PROTECT_RATE FIELD32(0x0000ffff)
#define GF40_PROT_CFG_PROTECT_CTRL FIELD32(0x00030000)
-#define GF40_PROT_CFG_PROTECT_NAV FIELD32(0x000c0000)
+#define GF40_PROT_CFG_PROTECT_NAV_SHORT FIELD32(0x00040000)
+#define GF40_PROT_CFG_PROTECT_NAV_LONG FIELD32(0x00080000)
#define GF40_PROT_CFG_TX_OP_ALLOW_CCK FIELD32(0x00100000)
#define GF40_PROT_CFG_TX_OP_ALLOW_OFDM FIELD32(0x00200000)
#define GF40_PROT_CFG_TX_OP_ALLOW_MM20 FIELD32(0x00400000)
diff --git a/drivers/net/wireless/rt2x00/rt2800lib.c b/drivers/net/wireless/rt2x00/rt2800lib.c
index d23a5d8..5592180 100644
--- a/drivers/net/wireless/rt2x00/rt2800lib.c
+++ b/drivers/net/wireless/rt2x00/rt2800lib.c
@@ -2185,7 +2185,7 @@ static int rt2800_init_registers(struct rt2x00_dev *rt2x00dev)
rt2800_register_read(rt2x00dev, CCK_PROT_CFG, ®);
rt2x00_set_field32(®, CCK_PROT_CFG_PROTECT_RATE, 3);
rt2x00_set_field32(®, CCK_PROT_CFG_PROTECT_CTRL, 0);
- rt2x00_set_field32(®, CCK_PROT_CFG_PROTECT_NAV, 1);
+ rt2x00_set_field32(®, CCK_PROT_CFG_PROTECT_NAV_SHORT, 1);
rt2x00_set_field32(®, CCK_PROT_CFG_TX_OP_ALLOW_CCK, 1);
rt2x00_set_field32(®, CCK_PROT_CFG_TX_OP_ALLOW_OFDM, 1);
rt2x00_set_field32(®, CCK_PROT_CFG_TX_OP_ALLOW_MM20, 1);
@@ -2198,7 +2198,7 @@ static int rt2800_init_registers(struct rt2x00_dev *rt2x00dev)
rt2800_register_read(rt2x00dev, OFDM_PROT_CFG, ®);
rt2x00_set_field32(®, OFDM_PROT_CFG_PROTECT_RATE, 3);
rt2x00_set_field32(®, OFDM_PROT_CFG_PROTECT_CTRL, 0);
- rt2x00_set_field32(®, OFDM_PROT_CFG_PROTECT_NAV, 1);
+ rt2x00_set_field32(®, OFDM_PROT_CFG_PROTECT_NAV_SHORT, 1);
rt2x00_set_field32(®, OFDM_PROT_CFG_TX_OP_ALLOW_CCK, 1);
rt2x00_set_field32(®, OFDM_PROT_CFG_TX_OP_ALLOW_OFDM, 1);
rt2x00_set_field32(®, OFDM_PROT_CFG_TX_OP_ALLOW_MM20, 1);
@@ -2211,7 +2211,7 @@ static int rt2800_init_registers(struct rt2x00_dev *rt2x00dev)
rt2800_register_read(rt2x00dev, MM20_PROT_CFG, ®);
rt2x00_set_field32(®, MM20_PROT_CFG_PROTECT_RATE, 0x4004);
rt2x00_set_field32(®, MM20_PROT_CFG_PROTECT_CTRL, 0);
- rt2x00_set_field32(®, MM20_PROT_CFG_PROTECT_NAV, 1);
+ rt2x00_set_field32(®, MM20_PROT_CFG_PROTECT_NAV_SHORT, 1);
rt2x00_set_field32(®, MM20_PROT_CFG_TX_OP_ALLOW_CCK, 1);
rt2x00_set_field32(®, MM20_PROT_CFG_TX_OP_ALLOW_OFDM, 1);
rt2x00_set_field32(®, MM20_PROT_CFG_TX_OP_ALLOW_MM20, 1);
@@ -2224,7 +2224,7 @@ static int rt2800_init_registers(struct rt2x00_dev *rt2x00dev)
rt2800_register_read(rt2x00dev, MM40_PROT_CFG, ®);
rt2x00_set_field32(®, MM40_PROT_CFG_PROTECT_RATE, 0x4084);
rt2x00_set_field32(®, MM40_PROT_CFG_PROTECT_CTRL, 0);
- rt2x00_set_field32(®, MM40_PROT_CFG_PROTECT_NAV, 1);
+ rt2x00_set_field32(®, MM40_PROT_CFG_PROTECT_NAV_SHORT, 1);
rt2x00_set_field32(®, MM40_PROT_CFG_TX_OP_ALLOW_CCK, 1);
rt2x00_set_field32(®, MM40_PROT_CFG_TX_OP_ALLOW_OFDM, 1);
rt2x00_set_field32(®, MM40_PROT_CFG_TX_OP_ALLOW_MM20, 1);
@@ -2237,7 +2237,7 @@ static int rt2800_init_registers(struct rt2x00_dev *rt2x00dev)
rt2800_register_read(rt2x00dev, GF20_PROT_CFG, ®);
rt2x00_set_field32(®, GF20_PROT_CFG_PROTECT_RATE, 0x4004);
rt2x00_set_field32(®, GF20_PROT_CFG_PROTECT_CTRL, 0);
- rt2x00_set_field32(®, GF20_PROT_CFG_PROTECT_NAV, 1);
+ rt2x00_set_field32(®, GF20_PROT_CFG_PROTECT_NAV_SHORT, 1);
rt2x00_set_field32(®, GF20_PROT_CFG_TX_OP_ALLOW_CCK, 1);
rt2x00_set_field32(®, GF20_PROT_CFG_TX_OP_ALLOW_OFDM, 1);
rt2x00_set_field32(®, GF20_PROT_CFG_TX_OP_ALLOW_MM20, 1);
@@ -2250,7 +2250,7 @@ static int rt2800_init_registers(struct rt2x00_dev *rt2x00dev)
rt2800_register_read(rt2x00dev, GF40_PROT_CFG, ®);
rt2x00_set_field32(®, GF40_PROT_CFG_PROTECT_RATE, 0x4084);
rt2x00_set_field32(®, GF40_PROT_CFG_PROTECT_CTRL, 0);
- rt2x00_set_field32(®, GF40_PROT_CFG_PROTECT_NAV, 1);
+ rt2x00_set_field32(®, GF40_PROT_CFG_PROTECT_NAV_SHORT, 1);
rt2x00_set_field32(®, GF40_PROT_CFG_TX_OP_ALLOW_CCK, 1);
rt2x00_set_field32(®, GF40_PROT_CFG_TX_OP_ALLOW_OFDM, 1);
rt2x00_set_field32(®, GF40_PROT_CFG_TX_OP_ALLOW_MM20, 1);
--
1.7.2.3
^ permalink raw reply related [flat|nested] 8+ messages in thread
* [PATCH 7/8] rt2x00: Add/Modify the GPIO register definition
2011-02-20 12:56 ` [PATCH 6/8] rt2x00: Add/Modify protection related register definitions Ivo van Doorn
@ 2011-02-20 12:57 ` Ivo van Doorn
2011-02-20 12:57 ` [PATCH 8/8] rt2x00: Add support for RT5390 chip Ivo van Doorn
0 siblings, 1 reply; 8+ messages in thread
From: Ivo van Doorn @ 2011-02-20 12:57 UTC (permalink / raw
To: John W. Linville; +Cc: users, linux-wireless
From: Shiang Tu <shiang_tu@ralinktech.com>
Revise/Add GPIO register related definitions
Signed-off-by: Shiang Tu <shiang_tu@ralinktech.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
---
drivers/net/wireless/rt2x00/rt2800.h | 10 ++++++++--
drivers/net/wireless/rt2x00/rt2800lib.c | 2 +-
2 files changed, 9 insertions(+), 3 deletions(-)
diff --git a/drivers/net/wireless/rt2x00/rt2800.h b/drivers/net/wireless/rt2x00/rt2800.h
index d3a693b..591ac32 100644
--- a/drivers/net/wireless/rt2x00/rt2800.h
+++ b/drivers/net/wireless/rt2x00/rt2800.h
@@ -281,8 +281,14 @@
#define GPIO_CTRL_CFG_BIT5 FIELD32(0x00000020)
#define GPIO_CTRL_CFG_BIT6 FIELD32(0x00000040)
#define GPIO_CTRL_CFG_BIT7 FIELD32(0x00000080)
-#define GPIO_CTRL_CFG_BIT8 FIELD32(0x00000100)
-#define GPIO_CTRL_CFG_GPIOD FIELD32(0x00000800)
+#define GPIO_CTRL_CFG_GPIOD_BIT0 FIELD32(0x00000100)
+#define GPIO_CTRL_CFG_GPIOD_BIT1 FIELD32(0x00000200)
+#define GPIO_CTRL_CFG_GPIOD_BIT2 FIELD32(0x00000400)
+#define GPIO_CTRL_CFG_GPIOD_BIT3 FIELD32(0x00000800)
+#define GPIO_CTRL_CFG_GPIOD_BIT4 FIELD32(0x00001000)
+#define GPIO_CTRL_CFG_GPIOD_BIT5 FIELD32(0x00002000)
+#define GPIO_CTRL_CFG_GPIOD_BIT6 FIELD32(0x00004000)
+#define GPIO_CTRL_CFG_GPIOD_BIT7 FIELD32(0x00008000)
/*
* MCU_CMD_CFG
diff --git a/drivers/net/wireless/rt2x00/rt2800lib.c b/drivers/net/wireless/rt2x00/rt2800lib.c
index 5592180..bed97eb 100644
--- a/drivers/net/wireless/rt2x00/rt2800lib.c
+++ b/drivers/net/wireless/rt2x00/rt2800lib.c
@@ -1384,7 +1384,7 @@ static void rt2800_set_ant_diversity(struct rt2x00_dev *rt2x00dev,
eesk_pin, 0);
rt2800_register_read(rt2x00dev, GPIO_CTRL_CFG, ®);
- rt2x00_set_field32(®, GPIO_CTRL_CFG_GPIOD, 0);
+ rt2x00_set_field32(®, GPIO_CTRL_CFG_GPIOD_BIT3, 0);
rt2x00_set_field32(®, GPIO_CTRL_CFG_BIT3, gpio_bit3);
rt2800_register_write(rt2x00dev, GPIO_CTRL_CFG, reg);
}
--
1.7.2.3
^ permalink raw reply related [flat|nested] 8+ messages in thread
* [PATCH 8/8] rt2x00: Add support for RT5390 chip
2011-02-20 12:57 ` [PATCH 7/8] rt2x00: Add/Modify the GPIO register definition Ivo van Doorn
@ 2011-02-20 12:57 ` Ivo van Doorn
0 siblings, 0 replies; 8+ messages in thread
From: Ivo van Doorn @ 2011-02-20 12:57 UTC (permalink / raw
To: John W. Linville; +Cc: users, linux-wireless
From: RA-Shiang Tu <Shiang_Tu@ralinktech.com>
Add new RT5390 chip support
Signed-off-by: Shiang Tu <shiang_tu@ralinktech.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
---
drivers/net/wireless/rt2x00/Kconfig | 12 +
drivers/net/wireless/rt2x00/rt2800.h | 59 +++++-
drivers/net/wireless/rt2x00/rt2800lib.c | 413 +++++++++++++++++++++++++++----
drivers/net/wireless/rt2x00/rt2800pci.c | 10 +
drivers/net/wireless/rt2x00/rt2x00.h | 1 +
5 files changed, 440 insertions(+), 55 deletions(-)
diff --git a/drivers/net/wireless/rt2x00/Kconfig b/drivers/net/wireless/rt2x00/Kconfig
index 6f383cd..f630552 100644
--- a/drivers/net/wireless/rt2x00/Kconfig
+++ b/drivers/net/wireless/rt2x00/Kconfig
@@ -97,6 +97,18 @@ config RT2800PCI_RT35XX
Support for these devices is non-functional at the moment and is
intended for testers and developers.
+config RT2800PCI_RT53XX
+ bool "rt2800-pci - Include support for rt53xx devices (EXPERIMENTAL)"
+ depends on EXPERIMENTAL
+ default n
+ ---help---
+ This adds support for rt53xx wireless chipset family to the
+ rt2800pci driver.
+ Supported chips: RT5390
+
+ Support for these devices is non-functional at the moment and is
+ intended for testers and developers.
+
endif
config RT2500USB
diff --git a/drivers/net/wireless/rt2x00/rt2800.h b/drivers/net/wireless/rt2x00/rt2800.h
index 591ac32..6f4a243 100644
--- a/drivers/net/wireless/rt2x00/rt2800.h
+++ b/drivers/net/wireless/rt2x00/rt2800.h
@@ -51,6 +51,7 @@
* RF3320 2.4G 1T1R(RT3350/RT3370/RT3390)
* RF3322 2.4G 2T2R(RT3352/RT3371/RT3372/RT3391/RT3392)
* RF3853 2.4G/5G 3T3R(RT3883/RT3563/RT3573/RT3593/RT3662)
+ * RF5390 2.4G 1T1R
*/
#define RF2820 0x0001
#define RF2850 0x0002
@@ -65,6 +66,7 @@
#define RF3320 0x000b
#define RF3322 0x000c
#define RF3853 0x000d
+#define RF5390 0x5390
/*
* Chipset revisions.
@@ -77,6 +79,7 @@
#define REV_RT3071E 0x0211
#define REV_RT3090E 0x0211
#define REV_RT3390E 0x0211
+#define REV_RT5390F 0x0502
/*
* Signal information.
@@ -121,6 +124,13 @@
#define E2PROM_CSR_RELOAD FIELD32(0x00000080)
/*
+ * AUX_CTRL: Aux/PCI-E related configuration
+ */
+#define AUX_CTRL 0x10c
+#define AUX_CTRL_WAKE_PCIE_EN FIELD32(0x00000002)
+#define AUX_CTRL_FORCE_PCIE_CLK FIELD32(0x00000400)
+
+/*
* OPT_14: Unknown register used by rt3xxx devices.
*/
#define OPT_14_CSR 0x0114
@@ -454,7 +464,7 @@
*/
#define RF_CSR_CFG 0x0500
#define RF_CSR_CFG_DATA FIELD32(0x000000ff)
-#define RF_CSR_CFG_REGNUM FIELD32(0x00001f00)
+#define RF_CSR_CFG_REGNUM FIELD32(0x00003f00)
#define RF_CSR_CFG_WRITE FIELD32(0x00010000)
#define RF_CSR_CFG_BUSY FIELD32(0x00020000)
@@ -1736,6 +1746,13 @@ struct mac_iveiv_entry {
*/
#define BBP4_TX_BF FIELD8(0x01)
#define BBP4_BANDWIDTH FIELD8(0x18)
+#define BBP4_MAC_IF_CTRL FIELD8(0x40)
+
+/*
+ * BBP 109
+ */
+#define BBP109_TX0_POWER FIELD8(0x0f)
+#define BBP109_TX1_POWER FIELD8(0xf0)
/*
* BBP 138: Unknown
@@ -1746,6 +1763,11 @@ struct mac_iveiv_entry {
#define BBP138_TX_DAC2 FIELD8(0x40)
/*
+ * BBP 152: Rx Ant
+ */
+#define BBP152_RX_DEFAULT_ANT FIELD8(0x80)
+
+/*
* RFCSR registers
* The wordsize of the RFCSR is 8 bits.
*/
@@ -1754,12 +1776,18 @@ struct mac_iveiv_entry {
* RFCSR 1:
*/
#define RFCSR1_RF_BLOCK_EN FIELD8(0x01)
+#define RFCSR1_PLL_PD FIELD8(0x02)
#define RFCSR1_RX0_PD FIELD8(0x04)
#define RFCSR1_TX0_PD FIELD8(0x08)
#define RFCSR1_RX1_PD FIELD8(0x10)
#define RFCSR1_TX1_PD FIELD8(0x20)
/*
+ * RFCSR 2:
+ */
+#define RFCSR2_RESCAL_EN FIELD8(0x80)
+
+/*
* RFCSR 6:
*/
#define RFCSR6_R1 FIELD8(0x03)
@@ -1771,6 +1799,11 @@ struct mac_iveiv_entry {
#define RFCSR7_RF_TUNING FIELD8(0x01)
/*
+ * RFCSR 11:
+ */
+#define RFCSR11_R FIELD8(0x03)
+
+/*
* RFCSR 12:
*/
#define RFCSR12_TX_POWER FIELD8(0x1f)
@@ -1791,6 +1824,7 @@ struct mac_iveiv_entry {
#define RFCSR17_TXMIXER_GAIN FIELD8(0x07)
#define RFCSR17_TX_LO1_EN FIELD8(0x08)
#define RFCSR17_R FIELD8(0x20)
+#define RFCSR17_CODE FIELD8(0x7f)
/*
* RFCSR 20:
@@ -1823,6 +1857,9 @@ struct mac_iveiv_entry {
/*
* RFCSR 30:
*/
+#define RFCSR30_TX_H20M FIELD8(0x02)
+#define RFCSR30_RX_H20M FIELD8(0x04)
+#define RFCSR30_RX_VCM FIELD8(0x18)
#define RFCSR30_RF_CALIBRATION FIELD8(0x80)
/*
@@ -1832,6 +1869,21 @@ struct mac_iveiv_entry {
#define RFCSR31_RX_H20M FIELD8(0x20)
/*
+ * RFCSR 38:
+ */
+#define RFCSR38_RX_LO1_EN FIELD8(0x20)
+
+/*
+ * RFCSR 39:
+ */
+#define RFCSR39_RX_LO2_EN FIELD8(0x80)
+
+/*
+ * RFCSR 49:
+ */
+#define RFCSR49_TX FIELD8(0x3f)
+
+/*
* RF registers
*/
@@ -1864,6 +1916,11 @@ struct mac_iveiv_entry {
*/
/*
+ * Chip ID
+ */
+#define EEPROM_CHIP_ID 0x0000
+
+/*
* EEPROM Version
*/
#define EEPROM_VERSION 0x0001
diff --git a/drivers/net/wireless/rt2x00/rt2800lib.c b/drivers/net/wireless/rt2x00/rt2800lib.c
index bed97eb..af9cef0 100644
--- a/drivers/net/wireless/rt2x00/rt2800lib.c
+++ b/drivers/net/wireless/rt2x00/rt2800lib.c
@@ -400,8 +400,15 @@ int rt2800_load_firmware(struct rt2x00_dev *rt2x00dev,
if (rt2800_wait_csr_ready(rt2x00dev))
return -EBUSY;
- if (rt2x00_is_pci(rt2x00dev))
+ if (rt2x00_is_pci(rt2x00dev)) {
+ if (rt2x00_rt(rt2x00dev, RT5390)) {
+ rt2800_register_read(rt2x00dev, AUX_CTRL, ®);
+ rt2x00_set_field32(®, AUX_CTRL_FORCE_PCIE_CLK, 1);
+ rt2x00_set_field32(®, AUX_CTRL_WAKE_PCIE_EN, 1);
+ rt2800_register_write(rt2x00dev, AUX_CTRL, reg);
+ }
rt2800_register_write(rt2x00dev, PWR_PIN_CFG, 0x00000002);
+ }
/*
* Disable DMA, will be reenabled later when enabling
@@ -1565,6 +1572,99 @@ static void rt2800_config_channel_rf3xxx(struct rt2x00_dev *rt2x00dev,
rt2800_rfcsr_write(rt2x00dev, 7, rfcsr);
}
+
+#define RT5390_POWER_BOUND 0x27
+#define RT5390_FREQ_OFFSET_BOUND 0x5f
+
+static void rt2800_config_channel_rf53xx(struct rt2x00_dev *rt2x00dev,
+ struct ieee80211_conf *conf,
+ struct rf_channel *rf,
+ struct channel_info *info)
+{
+ u8 rfcsr;
+ u16 eeprom;
+
+ rt2800_rfcsr_write(rt2x00dev, 8, rf->rf1);
+ rt2800_rfcsr_write(rt2x00dev, 9, rf->rf3);
+ rt2800_rfcsr_read(rt2x00dev, 11, &rfcsr);
+ rt2x00_set_field8(&rfcsr, RFCSR11_R, rf->rf2);
+ rt2800_rfcsr_write(rt2x00dev, 11, rfcsr);
+
+ rt2800_rfcsr_read(rt2x00dev, 49, &rfcsr);
+ if (info->default_power1 > RT5390_POWER_BOUND)
+ rt2x00_set_field8(&rfcsr, RFCSR49_TX, RT5390_POWER_BOUND);
+ else
+ rt2x00_set_field8(&rfcsr, RFCSR49_TX, info->default_power1);
+ rt2800_rfcsr_write(rt2x00dev, 49, rfcsr);
+
+ rt2800_rfcsr_read(rt2x00dev, 1, &rfcsr);
+ rt2x00_set_field8(&rfcsr, RFCSR1_RF_BLOCK_EN, 1);
+ rt2x00_set_field8(&rfcsr, RFCSR1_PLL_PD, 1);
+ rt2x00_set_field8(&rfcsr, RFCSR1_RX0_PD, 1);
+ rt2x00_set_field8(&rfcsr, RFCSR1_TX0_PD, 1);
+ rt2800_rfcsr_write(rt2x00dev, 1, rfcsr);
+
+ rt2800_rfcsr_read(rt2x00dev, 17, &rfcsr);
+ if (rt2x00dev->freq_offset > RT5390_FREQ_OFFSET_BOUND)
+ rt2x00_set_field8(&rfcsr, RFCSR17_CODE, RT5390_FREQ_OFFSET_BOUND);
+ else
+ rt2x00_set_field8(&rfcsr, RFCSR17_CODE, rt2x00dev->freq_offset);
+ rt2800_rfcsr_write(rt2x00dev, 17, rfcsr);
+
+ rt2x00_eeprom_read(rt2x00dev, EEPROM_NIC_CONF1, &eeprom);
+ if (rf->channel <= 14) {
+ int idx = rf->channel-1;
+
+ if (rt2x00_get_field16(eeprom, EEPROM_NIC_CONF1_BT_COEXIST)) {
+ if (rt2x00_rt_rev_gte(rt2x00dev, RT5390, REV_RT5390F)) {
+ /* r55/r59 value array of channel 1~14 */
+ static const char r55_bt_rev[] = {0x83, 0x83,
+ 0x83, 0x73, 0x73, 0x63, 0x53, 0x53,
+ 0x53, 0x43, 0x43, 0x43, 0x43, 0x43};
+ static const char r59_bt_rev[] = {0x0e, 0x0e,
+ 0x0e, 0x0e, 0x0e, 0x0b, 0x0a, 0x09,
+ 0x07, 0x07, 0x07, 0x07, 0x07, 0x07};
+
+ rt2800_rfcsr_write(rt2x00dev, 55, r55_bt_rev[idx]);
+ rt2800_rfcsr_write(rt2x00dev, 59, r59_bt_rev[idx]);
+ } else {
+ static const char r59_bt[] = {0x8b, 0x8b, 0x8b,
+ 0x8b, 0x8b, 0x8b, 0x8b, 0x8a, 0x89,
+ 0x88, 0x88, 0x86, 0x85, 0x84};
+
+ rt2800_rfcsr_write(rt2x00dev, 59, r59_bt[idx]);
+ }
+ } else {
+ if (rt2x00_rt_rev_gte(rt2x00dev, RT5390, REV_RT5390F)) {
+ static const char r55_nonbt_rev[] = {0x23, 0x23,
+ 0x23, 0x23, 0x13, 0x13, 0x03, 0x03,
+ 0x03, 0x03, 0x03, 0x03, 0x03, 0x03};
+ static const char r59_nonbt_rev[] = {0x07, 0x07,
+ 0x07, 0x07, 0x07, 0x07, 0x07, 0x07,
+ 0x07, 0x07, 0x06, 0x05, 0x04, 0x04};
+
+ rt2800_rfcsr_write(rt2x00dev, 55, r55_nonbt_rev[idx]);
+ rt2800_rfcsr_write(rt2x00dev, 59, r59_nonbt_rev[idx]);
+ } else if (rt2x00_rt(rt2x00dev, RT5390)) {
+ static const char r59_non_bt[] = {0x8f, 0x8f,
+ 0x8f, 0x8f, 0x8f, 0x8f, 0x8f, 0x8d,
+ 0x8a, 0x88, 0x88, 0x87, 0x87, 0x86};
+
+ rt2800_rfcsr_write(rt2x00dev, 59, r59_non_bt[idx]);
+ }
+ }
+ }
+
+ rt2800_rfcsr_read(rt2x00dev, 30, &rfcsr);
+ rt2x00_set_field8(&rfcsr, RFCSR30_TX_H20M, 0);
+ rt2x00_set_field8(&rfcsr, RFCSR30_RX_H20M, 0);
+ rt2800_rfcsr_write(rt2x00dev, 30, rfcsr);
+
+ rt2800_rfcsr_read(rt2x00dev, 3, &rfcsr);
+ rt2x00_set_field8(&rfcsr, RFCSR30_RF_CALIBRATION, 1);
+ rt2800_rfcsr_write(rt2x00dev, 3, rfcsr);
+}
+
static void rt2800_config_channel(struct rt2x00_dev *rt2x00dev,
struct ieee80211_conf *conf,
struct rf_channel *rf,
@@ -1589,6 +1689,8 @@ static void rt2800_config_channel(struct rt2x00_dev *rt2x00dev,
rt2x00_rf(rt2x00dev, RF3052) ||
rt2x00_rf(rt2x00dev, RF3320))
rt2800_config_channel_rf3xxx(rt2x00dev, conf, rf, info);
+ else if (rt2x00_rf(rt2x00dev, RF5390))
+ rt2800_config_channel_rf53xx(rt2x00dev, conf, rf, info);
else
rt2800_config_channel_rf2xxx(rt2x00dev, conf, rf, info);
@@ -1601,12 +1703,14 @@ static void rt2800_config_channel(struct rt2x00_dev *rt2x00dev,
rt2800_bbp_write(rt2x00dev, 86, 0);
if (rf->channel <= 14) {
- if (test_bit(CONFIG_EXTERNAL_LNA_BG, &rt2x00dev->flags)) {
- rt2800_bbp_write(rt2x00dev, 82, 0x62);
- rt2800_bbp_write(rt2x00dev, 75, 0x46);
- } else {
- rt2800_bbp_write(rt2x00dev, 82, 0x84);
- rt2800_bbp_write(rt2x00dev, 75, 0x50);
+ if (!rt2x00_rt(rt2x00dev, RT5390)) {
+ if (test_bit(CONFIG_EXTERNAL_LNA_BG, &rt2x00dev->flags)) {
+ rt2800_bbp_write(rt2x00dev, 82, 0x62);
+ rt2800_bbp_write(rt2x00dev, 75, 0x46);
+ } else {
+ rt2800_bbp_write(rt2x00dev, 82, 0x84);
+ rt2800_bbp_write(rt2x00dev, 75, 0x50);
+ }
}
} else {
rt2800_bbp_write(rt2x00dev, 82, 0xf2);
@@ -1985,7 +2089,8 @@ static u8 rt2800_get_default_vgc(struct rt2x00_dev *rt2x00dev)
if (rt2x00_rt(rt2x00dev, RT3070) ||
rt2x00_rt(rt2x00dev, RT3071) ||
rt2x00_rt(rt2x00dev, RT3090) ||
- rt2x00_rt(rt2x00dev, RT3390))
+ rt2x00_rt(rt2x00dev, RT3390) ||
+ rt2x00_rt(rt2x00dev, RT5390))
return 0x1c + (2 * rt2x00dev->lna_gain);
else
return 0x2e + rt2x00dev->lna_gain;
@@ -2117,6 +2222,10 @@ static int rt2800_init_registers(struct rt2x00_dev *rt2x00dev)
rt2800_register_write(rt2x00dev, TX_SW_CFG0, 0x00000400);
rt2800_register_write(rt2x00dev, TX_SW_CFG1, 0x00000000);
rt2800_register_write(rt2x00dev, TX_SW_CFG2, 0x0000001f);
+ } else if (rt2x00_rt(rt2x00dev, RT5390)) {
+ rt2800_register_write(rt2x00dev, TX_SW_CFG0, 0x00000404);
+ rt2800_register_write(rt2x00dev, TX_SW_CFG1, 0x00080606);
+ rt2800_register_write(rt2x00dev, TX_SW_CFG2, 0x00000000);
} else {
rt2800_register_write(rt2x00dev, TX_SW_CFG0, 0x00000000);
rt2800_register_write(rt2x00dev, TX_SW_CFG1, 0x00080606);
@@ -2492,15 +2601,31 @@ static int rt2800_init_bbp(struct rt2x00_dev *rt2x00dev)
rt2800_wait_bbp_ready(rt2x00dev)))
return -EACCES;
- if (rt2800_is_305x_soc(rt2x00dev))
+ if (rt2x00_rt(rt2x00dev, RT5390)) {
+ rt2800_bbp_read(rt2x00dev, 4, &value);
+ rt2x00_set_field8(&value, BBP4_MAC_IF_CTRL, 1);
+ rt2800_bbp_write(rt2x00dev, 4, value);
+ }
+
+ if (rt2800_is_305x_soc(rt2x00dev) ||
+ rt2x00_rt(rt2x00dev, RT5390))
rt2800_bbp_write(rt2x00dev, 31, 0x08);
rt2800_bbp_write(rt2x00dev, 65, 0x2c);
rt2800_bbp_write(rt2x00dev, 66, 0x38);
+ if (rt2x00_rt(rt2x00dev, RT5390))
+ rt2800_bbp_write(rt2x00dev, 68, 0x0b);
+
if (rt2x00_rt_rev(rt2x00dev, RT2860, REV_RT2860C)) {
rt2800_bbp_write(rt2x00dev, 69, 0x16);
rt2800_bbp_write(rt2x00dev, 73, 0x12);
+ } else if (rt2x00_rt(rt2x00dev, RT5390)) {
+ rt2800_bbp_write(rt2x00dev, 69, 0x12);
+ rt2800_bbp_write(rt2x00dev, 73, 0x13);
+ rt2800_bbp_write(rt2x00dev, 75, 0x46);
+ rt2800_bbp_write(rt2x00dev, 76, 0x28);
+ rt2800_bbp_write(rt2x00dev, 77, 0x59);
} else {
rt2800_bbp_write(rt2x00dev, 69, 0x12);
rt2800_bbp_write(rt2x00dev, 73, 0x10);
@@ -2511,7 +2636,8 @@ static int rt2800_init_bbp(struct rt2x00_dev *rt2x00dev)
if (rt2x00_rt(rt2x00dev, RT3070) ||
rt2x00_rt(rt2x00dev, RT3071) ||
rt2x00_rt(rt2x00dev, RT3090) ||
- rt2x00_rt(rt2x00dev, RT3390)) {
+ rt2x00_rt(rt2x00dev, RT3390) ||
+ rt2x00_rt(rt2x00dev, RT5390)) {
rt2800_bbp_write(rt2x00dev, 79, 0x13);
rt2800_bbp_write(rt2x00dev, 80, 0x05);
rt2800_bbp_write(rt2x00dev, 81, 0x33);
@@ -2523,35 +2649,62 @@ static int rt2800_init_bbp(struct rt2x00_dev *rt2x00dev)
}
rt2800_bbp_write(rt2x00dev, 82, 0x62);
- rt2800_bbp_write(rt2x00dev, 83, 0x6a);
+ if (rt2x00_rt(rt2x00dev, RT5390))
+ rt2800_bbp_write(rt2x00dev, 83, 0x7a);
+ else
+ rt2800_bbp_write(rt2x00dev, 83, 0x6a);
if (rt2x00_rt_rev(rt2x00dev, RT2860, REV_RT2860D))
rt2800_bbp_write(rt2x00dev, 84, 0x19);
+ else if (rt2x00_rt(rt2x00dev, RT5390))
+ rt2800_bbp_write(rt2x00dev, 84, 0x9a);
else
rt2800_bbp_write(rt2x00dev, 84, 0x99);
- rt2800_bbp_write(rt2x00dev, 86, 0x00);
+ if (rt2x00_rt(rt2x00dev, RT5390))
+ rt2800_bbp_write(rt2x00dev, 86, 0x38);
+ else
+ rt2800_bbp_write(rt2x00dev, 86, 0x00);
+
rt2800_bbp_write(rt2x00dev, 91, 0x04);
- rt2800_bbp_write(rt2x00dev, 92, 0x00);
+
+ if (rt2x00_rt(rt2x00dev, RT5390))
+ rt2800_bbp_write(rt2x00dev, 92, 0x02);
+ else
+ rt2800_bbp_write(rt2x00dev, 92, 0x00);
if (rt2x00_rt_rev_gte(rt2x00dev, RT3070, REV_RT3070F) ||
rt2x00_rt_rev_gte(rt2x00dev, RT3071, REV_RT3071E) ||
rt2x00_rt_rev_gte(rt2x00dev, RT3090, REV_RT3090E) ||
rt2x00_rt_rev_gte(rt2x00dev, RT3390, REV_RT3390E) ||
+ rt2x00_rt(rt2x00dev, RT5390) ||
rt2800_is_305x_soc(rt2x00dev))
rt2800_bbp_write(rt2x00dev, 103, 0xc0);
else
rt2800_bbp_write(rt2x00dev, 103, 0x00);
+ if (rt2x00_rt(rt2x00dev, RT5390))
+ rt2800_bbp_write(rt2x00dev, 104, 0x92);
+
if (rt2800_is_305x_soc(rt2x00dev))
rt2800_bbp_write(rt2x00dev, 105, 0x01);
+ else if (rt2x00_rt(rt2x00dev, RT5390))
+ rt2800_bbp_write(rt2x00dev, 105, 0x3c);
else
rt2800_bbp_write(rt2x00dev, 105, 0x05);
- rt2800_bbp_write(rt2x00dev, 106, 0x35);
+
+ if (rt2x00_rt(rt2x00dev, RT5390))
+ rt2800_bbp_write(rt2x00dev, 106, 0x03);
+ else
+ rt2800_bbp_write(rt2x00dev, 106, 0x35);
+
+ if (rt2x00_rt(rt2x00dev, RT5390))
+ rt2800_bbp_write(rt2x00dev, 128, 0x12);
if (rt2x00_rt(rt2x00dev, RT3071) ||
rt2x00_rt(rt2x00dev, RT3090) ||
- rt2x00_rt(rt2x00dev, RT3390)) {
+ rt2x00_rt(rt2x00dev, RT3390) ||
+ rt2x00_rt(rt2x00dev, RT5390)) {
rt2800_bbp_read(rt2x00dev, 138, &value);
rt2x00_eeprom_read(rt2x00dev, EEPROM_NIC_CONF0, &eeprom);
@@ -2563,6 +2716,41 @@ static int rt2800_init_bbp(struct rt2x00_dev *rt2x00dev)
rt2800_bbp_write(rt2x00dev, 138, value);
}
+ if (rt2x00_rt(rt2x00dev, RT5390)) {
+ int ant, div_mode;
+
+ rt2x00_eeprom_read(rt2x00dev, EEPROM_NIC_CONF1, &eeprom);
+ div_mode = rt2x00_get_field16(eeprom, EEPROM_NIC_CONF1_ANT_DIVERSITY);
+ ant = (div_mode == 3) ? 1 : 0;
+
+ /* check if this is a Bluetooth combo card */
+ rt2x00_eeprom_read(rt2x00dev, EEPROM_NIC_CONF1, &eeprom);
+ if (rt2x00_get_field16(eeprom, EEPROM_NIC_CONF1_BT_COEXIST)) {
+ u32 reg;
+
+ rt2800_register_read(rt2x00dev, GPIO_CTRL_CFG, ®);
+ rt2x00_set_field32(®, GPIO_CTRL_CFG_GPIOD_BIT3, 0);
+ rt2x00_set_field32(®, GPIO_CTRL_CFG_GPIOD_BIT6, 0);
+ rt2x00_set_field32(®, GPIO_CTRL_CFG_BIT3, 0);
+ rt2x00_set_field32(®, GPIO_CTRL_CFG_BIT6, 0);
+ if (ant == 0)
+ rt2x00_set_field32(®, GPIO_CTRL_CFG_BIT3, 1);
+ else if (ant == 1)
+ rt2x00_set_field32(®, GPIO_CTRL_CFG_BIT6, 1);
+ rt2800_register_write(rt2x00dev, GPIO_CTRL_CFG, reg);
+ }
+
+ rt2800_bbp_read(rt2x00dev, 152, &value);
+ if (ant == 0)
+ rt2x00_set_field8(&value, BBP152_RX_DEFAULT_ANT, 1);
+ else
+ rt2x00_set_field8(&value, BBP152_RX_DEFAULT_ANT, 0);
+ rt2800_bbp_write(rt2x00dev, 152, value);
+
+ /* Init frequency calibration */
+ rt2800_bbp_write(rt2x00dev, 142, 1);
+ rt2800_bbp_write(rt2x00dev, 143, 57);
+ }
for (i = 0; i < EEPROM_BBP_SIZE; i++) {
rt2x00_eeprom_read(rt2x00dev, EEPROM_BBP_START + i, &eeprom);
@@ -2652,18 +2840,28 @@ static int rt2800_init_rfcsr(struct rt2x00_dev *rt2x00dev)
!rt2x00_rt(rt2x00dev, RT3071) &&
!rt2x00_rt(rt2x00dev, RT3090) &&
!rt2x00_rt(rt2x00dev, RT3390) &&
+ !rt2x00_rt(rt2x00dev, RT5390) &&
!rt2800_is_305x_soc(rt2x00dev))
return 0;
/*
* Init RF calibration.
*/
- rt2800_rfcsr_read(rt2x00dev, 30, &rfcsr);
- rt2x00_set_field8(&rfcsr, RFCSR30_RF_CALIBRATION, 1);
- rt2800_rfcsr_write(rt2x00dev, 30, rfcsr);
- msleep(1);
- rt2x00_set_field8(&rfcsr, RFCSR30_RF_CALIBRATION, 0);
- rt2800_rfcsr_write(rt2x00dev, 30, rfcsr);
+ if (rt2x00_rt(rt2x00dev, RT5390)) {
+ rt2800_rfcsr_read(rt2x00dev, 2, &rfcsr);
+ rt2x00_set_field8(&rfcsr, RFCSR2_RESCAL_EN, 1);
+ rt2800_rfcsr_write(rt2x00dev, 2, rfcsr);
+ msleep(1);
+ rt2x00_set_field8(&rfcsr, RFCSR2_RESCAL_EN, 0);
+ rt2800_rfcsr_write(rt2x00dev, 2, rfcsr);
+ } else {
+ rt2800_rfcsr_read(rt2x00dev, 30, &rfcsr);
+ rt2x00_set_field8(&rfcsr, RFCSR30_RF_CALIBRATION, 1);
+ rt2800_rfcsr_write(rt2x00dev, 30, rfcsr);
+ msleep(1);
+ rt2x00_set_field8(&rfcsr, RFCSR30_RF_CALIBRATION, 0);
+ rt2800_rfcsr_write(rt2x00dev, 30, rfcsr);
+ }
if (rt2x00_rt(rt2x00dev, RT3070) ||
rt2x00_rt(rt2x00dev, RT3071) ||
@@ -2754,6 +2952,87 @@ static int rt2800_init_rfcsr(struct rt2x00_dev *rt2x00dev)
rt2800_rfcsr_write(rt2x00dev, 30, 0x00);
rt2800_rfcsr_write(rt2x00dev, 31, 0x00);
return 0;
+ } else if (rt2x00_rt(rt2x00dev, RT5390)) {
+ rt2800_rfcsr_write(rt2x00dev, 1, 0x0f);
+ rt2800_rfcsr_write(rt2x00dev, 2, 0x80);
+ rt2800_rfcsr_write(rt2x00dev, 3, 0x88);
+ rt2800_rfcsr_write(rt2x00dev, 5, 0x10);
+ if (rt2x00_rt_rev_gte(rt2x00dev, RT5390, REV_RT5390F))
+ rt2800_rfcsr_write(rt2x00dev, 6, 0xe0);
+ else
+ rt2800_rfcsr_write(rt2x00dev, 6, 0xa0);
+ rt2800_rfcsr_write(rt2x00dev, 7, 0x00);
+ rt2800_rfcsr_write(rt2x00dev, 10, 0x53);
+ rt2800_rfcsr_write(rt2x00dev, 11, 0x4a);
+ rt2800_rfcsr_write(rt2x00dev, 12, 0xc6);
+ rt2800_rfcsr_write(rt2x00dev, 13, 0x9f);
+ rt2800_rfcsr_write(rt2x00dev, 14, 0x00);
+ rt2800_rfcsr_write(rt2x00dev, 15, 0x00);
+ rt2800_rfcsr_write(rt2x00dev, 16, 0x00);
+ rt2800_rfcsr_write(rt2x00dev, 18, 0x03);
+ rt2800_rfcsr_write(rt2x00dev, 19, 0x00);
+
+ rt2800_rfcsr_write(rt2x00dev, 20, 0x00);
+ rt2800_rfcsr_write(rt2x00dev, 21, 0x00);
+ rt2800_rfcsr_write(rt2x00dev, 22, 0x20);
+ rt2800_rfcsr_write(rt2x00dev, 23, 0x00);
+ rt2800_rfcsr_write(rt2x00dev, 24, 0x00);
+ if (rt2x00_rt_rev_gte(rt2x00dev, RT5390, REV_RT5390F))
+ rt2800_rfcsr_write(rt2x00dev, 25, 0x80);
+ else
+ rt2800_rfcsr_write(rt2x00dev, 25, 0xc0);
+ rt2800_rfcsr_write(rt2x00dev, 26, 0x00);
+ rt2800_rfcsr_write(rt2x00dev, 27, 0x09);
+ rt2800_rfcsr_write(rt2x00dev, 28, 0x00);
+ rt2800_rfcsr_write(rt2x00dev, 29, 0x10);
+
+ rt2800_rfcsr_write(rt2x00dev, 30, 0x00);
+ rt2800_rfcsr_write(rt2x00dev, 31, 0x80);
+ rt2800_rfcsr_write(rt2x00dev, 32, 0x80);
+ rt2800_rfcsr_write(rt2x00dev, 33, 0x00);
+ rt2800_rfcsr_write(rt2x00dev, 34, 0x07);
+ rt2800_rfcsr_write(rt2x00dev, 35, 0x12);
+ rt2800_rfcsr_write(rt2x00dev, 36, 0x00);
+ rt2800_rfcsr_write(rt2x00dev, 37, 0x08);
+ rt2800_rfcsr_write(rt2x00dev, 38, 0x85);
+ rt2800_rfcsr_write(rt2x00dev, 39, 0x1b);
+
+ if (rt2x00_rt_rev_gte(rt2x00dev, RT5390, REV_RT5390F))
+ rt2800_rfcsr_write(rt2x00dev, 40, 0x0b);
+ else
+ rt2800_rfcsr_write(rt2x00dev, 40, 0x4b);
+ rt2800_rfcsr_write(rt2x00dev, 41, 0xbb);
+ rt2800_rfcsr_write(rt2x00dev, 42, 0xd2);
+ rt2800_rfcsr_write(rt2x00dev, 43, 0x9a);
+ rt2800_rfcsr_write(rt2x00dev, 44, 0x0e);
+ rt2800_rfcsr_write(rt2x00dev, 45, 0xa2);
+ if (rt2x00_rt_rev_gte(rt2x00dev, RT5390, REV_RT5390F))
+ rt2800_rfcsr_write(rt2x00dev, 46, 0x73);
+ else
+ rt2800_rfcsr_write(rt2x00dev, 46, 0x7b);
+ rt2800_rfcsr_write(rt2x00dev, 47, 0x00);
+ rt2800_rfcsr_write(rt2x00dev, 48, 0x10);
+ rt2800_rfcsr_write(rt2x00dev, 49, 0x94);
+
+ rt2800_rfcsr_write(rt2x00dev, 52, 0x38);
+ if (rt2x00_rt_rev_gte(rt2x00dev, RT5390, REV_RT5390F))
+ rt2800_rfcsr_write(rt2x00dev, 53, 0x00);
+ else
+ rt2800_rfcsr_write(rt2x00dev, 53, 0x84);
+ rt2800_rfcsr_write(rt2x00dev, 54, 0x78);
+ rt2800_rfcsr_write(rt2x00dev, 55, 0x44);
+ rt2800_rfcsr_write(rt2x00dev, 56, 0x22);
+ rt2800_rfcsr_write(rt2x00dev, 57, 0x80);
+ rt2800_rfcsr_write(rt2x00dev, 58, 0x7f);
+ rt2800_rfcsr_write(rt2x00dev, 59, 0x63);
+
+ rt2800_rfcsr_write(rt2x00dev, 60, 0x45);
+ if (rt2x00_rt_rev_gte(rt2x00dev, RT5390, REV_RT5390F))
+ rt2800_rfcsr_write(rt2x00dev, 61, 0xd1);
+ else
+ rt2800_rfcsr_write(rt2x00dev, 61, 0xdd);
+ rt2800_rfcsr_write(rt2x00dev, 62, 0x00);
+ rt2800_rfcsr_write(rt2x00dev, 63, 0x00);
}
if (rt2x00_rt_rev_lt(rt2x00dev, RT3070, REV_RT3070F)) {
@@ -2807,21 +3086,23 @@ static int rt2800_init_rfcsr(struct rt2x00_dev *rt2x00dev)
rt2800_init_rx_filter(rt2x00dev, true, 0x27, 0x15);
}
- /*
- * Set back to initial state
- */
- rt2800_bbp_write(rt2x00dev, 24, 0);
+ if (!rt2x00_rt(rt2x00dev, RT5390)) {
+ /*
+ * Set back to initial state
+ */
+ rt2800_bbp_write(rt2x00dev, 24, 0);
- rt2800_rfcsr_read(rt2x00dev, 22, &rfcsr);
- rt2x00_set_field8(&rfcsr, RFCSR22_BASEBAND_LOOPBACK, 0);
- rt2800_rfcsr_write(rt2x00dev, 22, rfcsr);
+ rt2800_rfcsr_read(rt2x00dev, 22, &rfcsr);
+ rt2x00_set_field8(&rfcsr, RFCSR22_BASEBAND_LOOPBACK, 0);
+ rt2800_rfcsr_write(rt2x00dev, 22, rfcsr);
- /*
- * set BBP back to BW20
- */
- rt2800_bbp_read(rt2x00dev, 4, &bbp);
- rt2x00_set_field8(&bbp, BBP4_BANDWIDTH, 0);
- rt2800_bbp_write(rt2x00dev, 4, bbp);
+ /*
+ * Set BBP back to BW20
+ */
+ rt2800_bbp_read(rt2x00dev, 4, &bbp);
+ rt2x00_set_field8(&bbp, BBP4_BANDWIDTH, 0);
+ rt2800_bbp_write(rt2x00dev, 4, bbp);
+ }
if (rt2x00_rt_rev_lt(rt2x00dev, RT3070, REV_RT3070F) ||
rt2x00_rt_rev_lt(rt2x00dev, RT3071, REV_RT3071E) ||
@@ -2833,21 +3114,23 @@ static int rt2800_init_rfcsr(struct rt2x00_dev *rt2x00dev)
rt2x00_set_field32(®, OPT_14_CSR_BIT0, 1);
rt2800_register_write(rt2x00dev, OPT_14_CSR, reg);
- rt2800_rfcsr_read(rt2x00dev, 17, &rfcsr);
- rt2x00_set_field8(&rfcsr, RFCSR17_TX_LO1_EN, 0);
- if (rt2x00_rt(rt2x00dev, RT3070) ||
- rt2x00_rt_rev_lt(rt2x00dev, RT3071, REV_RT3071E) ||
- rt2x00_rt_rev_lt(rt2x00dev, RT3090, REV_RT3090E) ||
- rt2x00_rt_rev_lt(rt2x00dev, RT3390, REV_RT3390E)) {
- if (!test_bit(CONFIG_EXTERNAL_LNA_BG, &rt2x00dev->flags))
- rt2x00_set_field8(&rfcsr, RFCSR17_R, 1);
- }
- rt2x00_eeprom_read(rt2x00dev, EEPROM_TXMIXER_GAIN_BG, &eeprom);
- if (rt2x00_get_field16(eeprom, EEPROM_TXMIXER_GAIN_BG_VAL) >= 1)
- rt2x00_set_field8(&rfcsr, RFCSR17_TXMIXER_GAIN,
- rt2x00_get_field16(eeprom,
- EEPROM_TXMIXER_GAIN_BG_VAL));
- rt2800_rfcsr_write(rt2x00dev, 17, rfcsr);
+ if (!rt2x00_rt(rt2x00dev, RT5390)) {
+ rt2800_rfcsr_read(rt2x00dev, 17, &rfcsr);
+ rt2x00_set_field8(&rfcsr, RFCSR17_TX_LO1_EN, 0);
+ if (rt2x00_rt(rt2x00dev, RT3070) ||
+ rt2x00_rt_rev_lt(rt2x00dev, RT3071, REV_RT3071E) ||
+ rt2x00_rt_rev_lt(rt2x00dev, RT3090, REV_RT3090E) ||
+ rt2x00_rt_rev_lt(rt2x00dev, RT3390, REV_RT3390E)) {
+ if (!test_bit(CONFIG_EXTERNAL_LNA_BG, &rt2x00dev->flags))
+ rt2x00_set_field8(&rfcsr, RFCSR17_R, 1);
+ }
+ rt2x00_eeprom_read(rt2x00dev, EEPROM_TXMIXER_GAIN_BG, &eeprom);
+ if (rt2x00_get_field16(eeprom, EEPROM_TXMIXER_GAIN_BG_VAL) >= 1)
+ rt2x00_set_field8(&rfcsr, RFCSR17_TXMIXER_GAIN,
+ rt2x00_get_field16(eeprom,
+ EEPROM_TXMIXER_GAIN_BG_VAL));
+ rt2800_rfcsr_write(rt2x00dev, 17, rfcsr);
+ }
if (rt2x00_rt(rt2x00dev, RT3090)) {
rt2800_bbp_read(rt2x00dev, 138, &bbp);
@@ -2898,6 +3181,20 @@ static int rt2800_init_rfcsr(struct rt2x00_dev *rt2x00dev)
rt2800_rfcsr_write(rt2x00dev, 27, rfcsr);
}
+ if (rt2x00_rt(rt2x00dev, RT5390)) {
+ rt2800_rfcsr_read(rt2x00dev, 38, &rfcsr);
+ rt2x00_set_field8(&rfcsr, RFCSR38_RX_LO1_EN, 0);
+ rt2800_rfcsr_write(rt2x00dev, 38, rfcsr);
+
+ rt2800_rfcsr_read(rt2x00dev, 39, &rfcsr);
+ rt2x00_set_field8(&rfcsr, RFCSR39_RX_LO2_EN, 0);
+ rt2800_rfcsr_write(rt2x00dev, 39, rfcsr);
+
+ rt2800_rfcsr_read(rt2x00dev, 30, &rfcsr);
+ rt2x00_set_field8(&rfcsr, RFCSR30_RX_VCM, 2);
+ rt2800_rfcsr_write(rt2x00dev, 30, rfcsr);
+ }
+
return 0;
}
@@ -3162,10 +3459,15 @@ int rt2800_init_eeprom(struct rt2x00_dev *rt2x00dev)
rt2x00_eeprom_read(rt2x00dev, EEPROM_NIC_CONF0, &eeprom);
/*
- * Identify RF chipset.
+ * Identify RF chipset by EEPROM value
+ * RT28xx/RT30xx: defined in "EEPROM_NIC_CONF0_RF_TYPE" field
+ * RT53xx: defined in "EEPROM_CHIP_ID" field
*/
- value = rt2x00_get_field16(eeprom, EEPROM_NIC_CONF0_RF_TYPE);
rt2800_register_read(rt2x00dev, MAC_CSR0, ®);
+ if (rt2x00_get_field32(reg, MAC_CSR0_CHIPSET) == RT5390)
+ rt2x00_eeprom_read(rt2x00dev, EEPROM_CHIP_ID, &value);
+ else
+ value = rt2x00_get_field16(eeprom, EEPROM_NIC_CONF0_RF_TYPE);
rt2x00_set_chip(rt2x00dev, rt2x00_get_field32(reg, MAC_CSR0_CHIPSET),
value, rt2x00_get_field32(reg, MAC_CSR0_REVISION));
@@ -3177,7 +3479,8 @@ int rt2800_init_eeprom(struct rt2x00_dev *rt2x00dev)
!rt2x00_rt(rt2x00dev, RT3071) &&
!rt2x00_rt(rt2x00dev, RT3090) &&
!rt2x00_rt(rt2x00dev, RT3390) &&
- !rt2x00_rt(rt2x00dev, RT3572)) {
+ !rt2x00_rt(rt2x00dev, RT3572) &&
+ !rt2x00_rt(rt2x00dev, RT5390)) {
ERROR(rt2x00dev, "Invalid RT chipset detected.\n");
return -ENODEV;
}
@@ -3191,7 +3494,8 @@ int rt2800_init_eeprom(struct rt2x00_dev *rt2x00dev)
!rt2x00_rf(rt2x00dev, RF3021) &&
!rt2x00_rf(rt2x00dev, RF3022) &&
!rt2x00_rf(rt2x00dev, RF3052) &&
- !rt2x00_rf(rt2x00dev, RF3320)) {
+ !rt2x00_rf(rt2x00dev, RF3320) &&
+ !rt2x00_rf(rt2x00dev, RF5390)) {
ERROR(rt2x00dev, "Invalid RF chipset detected.\n");
return -ENODEV;
}
@@ -3488,7 +3792,8 @@ int rt2800_probe_hw_mode(struct rt2x00_dev *rt2x00dev)
rt2x00_rf(rt2x00dev, RF2020) ||
rt2x00_rf(rt2x00dev, RF3021) ||
rt2x00_rf(rt2x00dev, RF3022) ||
- rt2x00_rf(rt2x00dev, RF3320)) {
+ rt2x00_rf(rt2x00dev, RF3320) ||
+ rt2x00_rf(rt2x00dev, RF5390)) {
spec->num_channels = 14;
spec->channels = rf_vals_3x;
} else if (rt2x00_rf(rt2x00dev, RF3052)) {
diff --git a/drivers/net/wireless/rt2x00/rt2800pci.c b/drivers/net/wireless/rt2x00/rt2800pci.c
index 8f4dfc3..cc7c90c 100644
--- a/drivers/net/wireless/rt2x00/rt2800pci.c
+++ b/drivers/net/wireless/rt2x00/rt2800pci.c
@@ -493,6 +493,13 @@ static int rt2800pci_init_registers(struct rt2x00_dev *rt2x00dev)
rt2800_register_write(rt2x00dev, PBF_SYS_CTRL, 0x00000e1f);
rt2800_register_write(rt2x00dev, PBF_SYS_CTRL, 0x00000e00);
+ if (rt2x00_rt(rt2x00dev, RT5390)) {
+ rt2800_register_read(rt2x00dev, AUX_CTRL, ®);
+ rt2x00_set_field32(®, AUX_CTRL_FORCE_PCIE_CLK, 1);
+ rt2x00_set_field32(®, AUX_CTRL_WAKE_PCIE_EN, 1);
+ rt2800_register_write(rt2x00dev, AUX_CTRL, reg);
+ }
+
rt2800_register_write(rt2x00dev, PWR_PIN_CFG, 0x00000003);
rt2800_register_read(rt2x00dev, MAC_SYS_CTRL, ®);
@@ -1125,6 +1132,9 @@ static DEFINE_PCI_DEVICE_TABLE(rt2800pci_device_table) = {
{ PCI_DEVICE(0x1814, 0x3592), PCI_DEVICE_DATA(&rt2800pci_ops) },
{ PCI_DEVICE(0x1814, 0x3593), PCI_DEVICE_DATA(&rt2800pci_ops) },
#endif
+#ifdef CONFIG_RT2800PCI_RT53XX
+ { PCI_DEVICE(0x1814, 0x5390), PCI_DEVICE_DATA(&rt2800pci_ops) },
+#endif
{ 0, }
};
#endif /* CONFIG_PCI */
diff --git a/drivers/net/wireless/rt2x00/rt2x00.h b/drivers/net/wireless/rt2x00/rt2x00.h
index 64c6ef5..1df432c 100644
--- a/drivers/net/wireless/rt2x00/rt2x00.h
+++ b/drivers/net/wireless/rt2x00/rt2x00.h
@@ -189,6 +189,7 @@ struct rt2x00_chip {
#define RT3572 0x3572
#define RT3593 0x3593 /* PCIe */
#define RT3883 0x3883 /* WSOC */
+#define RT5390 0x5390 /* 2.4GHz */
u16 rf;
u16 rev;
--
1.7.2.3
^ permalink raw reply related [flat|nested] 8+ messages in thread
end of thread, other threads:[~2011-02-20 12:58 UTC | newest]
Thread overview: 8+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2011-02-20 12:54 [PATCH 1/8] rt2x00: Add antenna setting for RT3070/RT3090/RT3390 with RX antenna diversity support Ivo van Doorn
2011-02-20 12:55 ` [PATCH 2/8] rt2x00: Fix rt2800 txpower setting to correct value Ivo van Doorn
2011-02-20 12:55 ` [PATCH 3/8] rt2x00: Minor optimization for devices with RTS/CTS offload Ivo van Doorn
2011-02-20 12:56 ` [PATCH 4/8] Revert "rt2x00 : avoid timestamp for monitor injected frame." Ivo van Doorn
2011-02-20 12:56 ` [PATCH 5/8] rt2x00: Remove superfluos empty line Ivo van Doorn
2011-02-20 12:56 ` [PATCH 6/8] rt2x00: Add/Modify protection related register definitions Ivo van Doorn
2011-02-20 12:57 ` [PATCH 7/8] rt2x00: Add/Modify the GPIO register definition Ivo van Doorn
2011-02-20 12:57 ` [PATCH 8/8] rt2x00: Add support for RT5390 chip Ivo van Doorn
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for read-only IMAP folder(s) and NNTP newsgroup(s).