* [PATCH v2 1/3] wifi: rt2x00: introduce DMA busy check watchdog for rt2800
[not found] <20231104085800.17576-1-yangshiji66@outlook.com>
@ 2023-11-04 8:57 ` Shiji Yang
2023-11-08 18:14 ` Kalle Valo
2023-11-04 8:57 ` [PATCH v2 2/3] wifi: rt2x00: disable RTS threshold for rt2800 by default Shiji Yang
2023-11-04 8:58 ` [PATCH v2 3/3] wifi: rt2x00: restart beacon queue when hardware reset Shiji Yang
2 siblings, 1 reply; 4+ messages in thread
From: Shiji Yang @ 2023-11-04 8:57 UTC (permalink / raw
To: linux-wireless; +Cc: Stanislaw Gruszka, Kalle Valo, linux-kernel, Shiji Yang
When I tried to fix the watchdog of rt2800, I found that sometimes
the watchdog can not reset the hung device. This is because the
queue is not completely stuck, it just becomes very slow. The MTK
vendor driver for the new chip MT7603/MT7612 has a DMA busy watchdog
to detect device hangs by checking DMA busy status. This watchdog
implementation is something similar to it. To reduce unnecessary
reset, we can check the INT_SOURCE_CSR register together as I found
that when the radio hung, the RX/TX coherent interrupt will always
stuck at triggered state.
The 'watchdog' module parameter has been extended to control all
watchdogs(0=disabled, 1=hang watchdog, 2=DMA watchdog, 3=both). This
new watchdog function is a slight schedule and it won't affect the
transmission speed. So we can turn on it by default. Due to the
INT_SOURCE_CSR register is invalid on rt2800 USB NICs, the DMA busy
watchdog will be automatically disabled for them.
Tested on MT7620 and RT5350.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
---
drivers/net/wireless/ralink/rt2x00/rt2800.h | 4 +
.../net/wireless/ralink/rt2x00/rt2800lib.c | 77 ++++++++++++++++---
drivers/net/wireless/ralink/rt2x00/rt2x00.h | 3 +
3 files changed, 73 insertions(+), 11 deletions(-)
diff --git a/drivers/net/wireless/ralink/rt2x00/rt2800.h b/drivers/net/wireless/ralink/rt2x00/rt2800.h
index 48521e455..8930589b4 100644
--- a/drivers/net/wireless/ralink/rt2x00/rt2800.h
+++ b/drivers/net/wireless/ralink/rt2x00/rt2800.h
@@ -3194,4 +3194,8 @@ enum rt2800_eeprom_word {
*/
#define BCN_TBTT_OFFSET 64
+/* Watchdog type mask */
+#define RT2800_WATCHDOG_HANG BIT(0)
+#define RT2800_WATCHDOG_DMA_BUSY BIT(1)
+
#endif /* RT2800_H */
diff --git a/drivers/net/wireless/ralink/rt2x00/rt2800lib.c b/drivers/net/wireless/ralink/rt2x00/rt2800lib.c
index 594dd3d9f..be4f7c144 100644
--- a/drivers/net/wireless/ralink/rt2x00/rt2800lib.c
+++ b/drivers/net/wireless/ralink/rt2x00/rt2800lib.c
@@ -30,9 +30,10 @@
#include "rt2800lib.h"
#include "rt2800.h"
-static bool modparam_watchdog;
-module_param_named(watchdog, modparam_watchdog, bool, S_IRUGO);
-MODULE_PARM_DESC(watchdog, "Enable watchdog to detect tx/rx hangs and reset hardware if detected");
+static unsigned int modparam_watchdog = RT2800_WATCHDOG_DMA_BUSY;
+module_param_named(watchdog, modparam_watchdog, uint, 0444);
+MODULE_PARM_DESC(watchdog, "Enable watchdog to recover tx/rx hangs.\n"
+ "\t\t(0=disabled, 1=hang watchdog, 2=DMA watchdog(default), 3=both)");
/*
* Register access.
@@ -1260,15 +1261,12 @@ static void rt2800_update_survey(struct rt2x00_dev *rt2x00dev)
chan_survey->time_ext_busy += rt2800_register_read(rt2x00dev, CH_BUSY_STA_SEC);
}
-void rt2800_watchdog(struct rt2x00_dev *rt2x00dev)
+static bool rt2800_watchdog_hung(struct rt2x00_dev *rt2x00dev)
{
struct data_queue *queue;
bool hung_tx = false;
bool hung_rx = false;
- if (test_bit(DEVICE_STATE_SCANNING, &rt2x00dev->flags))
- return;
-
rt2800_update_survey(rt2x00dev);
queue_for_each(rt2x00dev, queue) {
@@ -1296,18 +1294,72 @@ void rt2800_watchdog(struct rt2x00_dev *rt2x00dev)
}
}
+ if (!hung_tx && !hung_rx)
+ return false;
+
if (hung_tx)
rt2x00_warn(rt2x00dev, "Watchdog TX hung detected\n");
if (hung_rx)
rt2x00_warn(rt2x00dev, "Watchdog RX hung detected\n");
- if (hung_tx || hung_rx) {
- queue_for_each(rt2x00dev, queue)
- queue->wd_count = 0;
+ queue_for_each(rt2x00dev, queue)
+ queue->wd_count = 0;
+
+ return true;
+}
+
+static bool rt2800_watchdog_dma_busy(struct rt2x00_dev *rt2x00dev)
+{
+ bool busy_rx, busy_tx;
+ u32 reg_cfg = rt2800_register_read(rt2x00dev, WPDMA_GLO_CFG);
+ u32 reg_int = rt2800_register_read(rt2x00dev, INT_SOURCE_CSR);
+
+ if (rt2x00_get_field32(reg_cfg, WPDMA_GLO_CFG_RX_DMA_BUSY) &&
+ rt2x00_get_field32(reg_int, INT_SOURCE_CSR_RX_COHERENT))
+ rt2x00dev->rxdma_busy++;
+ else
+ rt2x00dev->rxdma_busy = 0;
+ if (rt2x00_get_field32(reg_cfg, WPDMA_GLO_CFG_TX_DMA_BUSY) &&
+ rt2x00_get_field32(reg_int, INT_SOURCE_CSR_TX_COHERENT))
+ rt2x00dev->txdma_busy++;
+ else
+ rt2x00dev->txdma_busy = 0;
+
+ busy_rx = rt2x00dev->rxdma_busy > 30 ? true : false;
+ busy_tx = rt2x00dev->txdma_busy > 30 ? true : false;
+
+ if (!busy_rx && !busy_tx)
+ return false;
+
+ if (busy_rx)
+ rt2x00_warn(rt2x00dev, "Watchdog RX DMA busy detected\n");
+
+ if (busy_tx)
+ rt2x00_warn(rt2x00dev, "Watchdog TX DMA busy detected\n");
+
+ rt2x00dev->rxdma_busy = 0;
+ rt2x00dev->txdma_busy = 0;
+
+ return true;
+}
+
+void rt2800_watchdog(struct rt2x00_dev *rt2x00dev)
+{
+ bool reset = false;
+
+ if (test_bit(DEVICE_STATE_SCANNING, &rt2x00dev->flags))
+ return;
+
+ if (modparam_watchdog & RT2800_WATCHDOG_DMA_BUSY)
+ reset = rt2800_watchdog_dma_busy(rt2x00dev);
+
+ if (modparam_watchdog & RT2800_WATCHDOG_HANG)
+ reset = rt2800_watchdog_hung(rt2x00dev) || reset;
+
+ if (reset)
ieee80211_restart_hw(rt2x00dev->hw);
- }
}
EXPORT_SYMBOL_GPL(rt2800_watchdog);
@@ -12015,6 +12067,9 @@ int rt2800_probe_hw(struct rt2x00_dev *rt2x00dev)
__set_bit(REQUIRE_TASKLET_CONTEXT, &rt2x00dev->cap_flags);
}
+ /* USB NICs don't support DMA watchdog as INT_SOURCE_CSR is invalid */
+ if (rt2x00_is_usb(rt2x00dev))
+ modparam_watchdog &= ~RT2800_WATCHDOG_DMA_BUSY;
if (modparam_watchdog) {
__set_bit(CAPABILITY_RESTART_HW, &rt2x00dev->cap_flags);
rt2x00dev->link.watchdog_interval = msecs_to_jiffies(100);
diff --git a/drivers/net/wireless/ralink/rt2x00/rt2x00.h b/drivers/net/wireless/ralink/rt2x00/rt2x00.h
index aaaf99331..62fed38f4 100644
--- a/drivers/net/wireless/ralink/rt2x00/rt2x00.h
+++ b/drivers/net/wireless/ralink/rt2x00/rt2x00.h
@@ -926,6 +926,9 @@ struct rt2x00_dev {
*/
u16 beacon_int;
+ /* Rx/Tx DMA busy watchdog counter */
+ u16 rxdma_busy, txdma_busy;
+
/**
* Timestamp of last received beacon
*/
--
2.39.2
^ permalink raw reply related [flat|nested] 4+ messages in thread
* [PATCH v2 2/3] wifi: rt2x00: disable RTS threshold for rt2800 by default
[not found] <20231104085800.17576-1-yangshiji66@outlook.com>
2023-11-04 8:57 ` [PATCH v2 1/3] wifi: rt2x00: introduce DMA busy check watchdog for rt2800 Shiji Yang
@ 2023-11-04 8:57 ` Shiji Yang
2023-11-04 8:58 ` [PATCH v2 3/3] wifi: rt2x00: restart beacon queue when hardware reset Shiji Yang
2 siblings, 0 replies; 4+ messages in thread
From: Shiji Yang @ 2023-11-04 8:57 UTC (permalink / raw
To: linux-wireless; +Cc: Stanislaw Gruszka, Kalle Valo, linux-kernel, Shiji Yang
rt2800 has a lot of registers to control the RTS enable/disable
status for different rates. And the driver control them via
rt2800_set_rts_threshold(). When RTS was disabled in user
interface, this function won't be called at all. This means that
the RTS is still 'on' for CCK and OFDM rates. So we'd better to
disable them by default because it should be like this. The RTS
for HT20 and HT40 is already default off so we don't need to
touch them. If we toggle the RTS status, these register bits
will be enable/disable again by rt2800_set_rts_threshold().
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
---
drivers/net/wireless/ralink/rt2x00/rt2800lib.c | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
diff --git a/drivers/net/wireless/ralink/rt2x00/rt2800lib.c b/drivers/net/wireless/ralink/rt2x00/rt2800lib.c
index be4f7c144..04855490f 100644
--- a/drivers/net/wireless/ralink/rt2x00/rt2800lib.c
+++ b/drivers/net/wireless/ralink/rt2x00/rt2800lib.c
@@ -6099,7 +6099,7 @@ static int rt2800_init_registers(struct rt2x00_dev *rt2x00dev)
rt2x00_set_field32(®, CCK_PROT_CFG_TX_OP_ALLOW_MM40, 0);
rt2x00_set_field32(®, CCK_PROT_CFG_TX_OP_ALLOW_GF20, 1);
rt2x00_set_field32(®, CCK_PROT_CFG_TX_OP_ALLOW_GF40, 0);
- rt2x00_set_field32(®, CCK_PROT_CFG_RTS_TH_EN, 1);
+ rt2x00_set_field32(®, CCK_PROT_CFG_RTS_TH_EN, 0);
rt2800_register_write(rt2x00dev, CCK_PROT_CFG, reg);
reg = rt2800_register_read(rt2x00dev, OFDM_PROT_CFG);
@@ -6112,7 +6112,7 @@ static int rt2800_init_registers(struct rt2x00_dev *rt2x00dev)
rt2x00_set_field32(®, OFDM_PROT_CFG_TX_OP_ALLOW_MM40, 0);
rt2x00_set_field32(®, OFDM_PROT_CFG_TX_OP_ALLOW_GF20, 1);
rt2x00_set_field32(®, OFDM_PROT_CFG_TX_OP_ALLOW_GF40, 0);
- rt2x00_set_field32(®, OFDM_PROT_CFG_RTS_TH_EN, 1);
+ rt2x00_set_field32(®, OFDM_PROT_CFG_RTS_TH_EN, 0);
rt2800_register_write(rt2x00dev, OFDM_PROT_CFG, reg);
reg = rt2800_register_read(rt2x00dev, MM20_PROT_CFG);
--
2.39.2
^ permalink raw reply related [flat|nested] 4+ messages in thread
* [PATCH v2 3/3] wifi: rt2x00: restart beacon queue when hardware reset
[not found] <20231104085800.17576-1-yangshiji66@outlook.com>
2023-11-04 8:57 ` [PATCH v2 1/3] wifi: rt2x00: introduce DMA busy check watchdog for rt2800 Shiji Yang
2023-11-04 8:57 ` [PATCH v2 2/3] wifi: rt2x00: disable RTS threshold for rt2800 by default Shiji Yang
@ 2023-11-04 8:58 ` Shiji Yang
2 siblings, 0 replies; 4+ messages in thread
From: Shiji Yang @ 2023-11-04 8:58 UTC (permalink / raw
To: linux-wireless; +Cc: Stanislaw Gruszka, Kalle Valo, linux-kernel, Shiji Yang
When a hardware reset is triggered, all registers are reset, so all
queues are forced to stop in hardware interface. However, mac80211
will not automatically stop the queue. If we don't manually stop the
beacon queue, the queue will be deadlocked and unable to start again.
This patch fixes the issue where Apple devices cannot connect to the
AP after calling ieee80211_restart_hw().
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
---
drivers/net/wireless/ralink/rt2x00/rt2x00dev.c | 3 +++
drivers/net/wireless/ralink/rt2x00/rt2x00mac.c | 11 +++++++++++
2 files changed, 14 insertions(+)
diff --git a/drivers/net/wireless/ralink/rt2x00/rt2x00dev.c b/drivers/net/wireless/ralink/rt2x00/rt2x00dev.c
index 9a9cfd0ce..00b945053 100644
--- a/drivers/net/wireless/ralink/rt2x00/rt2x00dev.c
+++ b/drivers/net/wireless/ralink/rt2x00/rt2x00dev.c
@@ -101,6 +101,7 @@ void rt2x00lib_disable_radio(struct rt2x00_dev *rt2x00dev)
rt2x00link_stop_tuner(rt2x00dev);
rt2x00queue_stop_queues(rt2x00dev);
rt2x00queue_flush_queues(rt2x00dev, true);
+ rt2x00queue_stop_queue(rt2x00dev->bcn);
/*
* Disable radio.
@@ -1286,6 +1287,7 @@ int rt2x00lib_start(struct rt2x00_dev *rt2x00dev)
rt2x00dev->intf_ap_count = 0;
rt2x00dev->intf_sta_count = 0;
rt2x00dev->intf_associated = 0;
+ rt2x00dev->intf_beaconing = 0;
/* Enable the radio */
retval = rt2x00lib_enable_radio(rt2x00dev);
@@ -1312,6 +1314,7 @@ void rt2x00lib_stop(struct rt2x00_dev *rt2x00dev)
rt2x00dev->intf_ap_count = 0;
rt2x00dev->intf_sta_count = 0;
rt2x00dev->intf_associated = 0;
+ rt2x00dev->intf_beaconing = 0;
}
static inline void rt2x00lib_set_if_combinations(struct rt2x00_dev *rt2x00dev)
diff --git a/drivers/net/wireless/ralink/rt2x00/rt2x00mac.c b/drivers/net/wireless/ralink/rt2x00/rt2x00mac.c
index 4202c6517..75fda72c1 100644
--- a/drivers/net/wireless/ralink/rt2x00/rt2x00mac.c
+++ b/drivers/net/wireless/ralink/rt2x00/rt2x00mac.c
@@ -598,6 +598,17 @@ void rt2x00mac_bss_info_changed(struct ieee80211_hw *hw,
*/
if (changes & BSS_CHANGED_BEACON_ENABLED) {
mutex_lock(&intf->beacon_skb_mutex);
+
+ /*
+ * Clear the 'enable_beacon' flag and clear beacon because
+ * the beacon queue has been stopped after hardware reset.
+ */
+ if (test_bit(DEVICE_STATE_RESET, &rt2x00dev->flags) &&
+ intf->enable_beacon) {
+ intf->enable_beacon = false;
+ rt2x00queue_clear_beacon(rt2x00dev, vif);
+ }
+
if (!bss_conf->enable_beacon && intf->enable_beacon) {
rt2x00dev->intf_beaconing--;
intf->enable_beacon = false;
--
2.39.2
^ permalink raw reply related [flat|nested] 4+ messages in thread
* Re: [PATCH v2 1/3] wifi: rt2x00: introduce DMA busy check watchdog for rt2800
2023-11-04 8:57 ` [PATCH v2 1/3] wifi: rt2x00: introduce DMA busy check watchdog for rt2800 Shiji Yang
@ 2023-11-08 18:14 ` Kalle Valo
0 siblings, 0 replies; 4+ messages in thread
From: Kalle Valo @ 2023-11-08 18:14 UTC (permalink / raw
To: Shiji Yang; +Cc: linux-wireless, Stanislaw Gruszka, linux-kernel, Shiji Yang
Shiji Yang <yangshiji66@outlook.com> wrote:
> When I tried to fix the watchdog of rt2800, I found that sometimes
> the watchdog can not reset the hung device. This is because the
> queue is not completely stuck, it just becomes very slow. The MTK
> vendor driver for the new chip MT7603/MT7612 has a DMA busy watchdog
> to detect device hangs by checking DMA busy status. This watchdog
> implementation is something similar to it. To reduce unnecessary
> reset, we can check the INT_SOURCE_CSR register together as I found
> that when the radio hung, the RX/TX coherent interrupt will always
> stuck at triggered state.
>
> The 'watchdog' module parameter has been extended to control all
> watchdogs(0=disabled, 1=hang watchdog, 2=DMA watchdog, 3=both). This
> new watchdog function is a slight schedule and it won't affect the
> transmission speed. So we can turn on it by default. Due to the
> INT_SOURCE_CSR register is invalid on rt2800 USB NICs, the DMA busy
> watchdog will be automatically disabled for them.
>
> Tested on MT7620 and RT5350.
>
> Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
> Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
3 patches applied to wireless-next.git, thanks.
b1275cdd7456 wifi: rt2x00: introduce DMA busy check watchdog for rt2800
570beb6285fd wifi: rt2x00: disable RTS threshold for rt2800 by default
a11d965a218f wifi: rt2x00: restart beacon queue when hardware reset
--
https://patchwork.kernel.org/project/linux-wireless/patch/TYAP286MB0315D7462CE08A119A99DE34BCA4A@TYAP286MB0315.JPNP286.PROD.OUTLOOK.COM/
https://wireless.wiki.kernel.org/en/developers/documentation/submittingpatches
^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2023-11-08 18:14 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
[not found] <20231104085800.17576-1-yangshiji66@outlook.com>
2023-11-04 8:57 ` [PATCH v2 1/3] wifi: rt2x00: introduce DMA busy check watchdog for rt2800 Shiji Yang
2023-11-08 18:14 ` Kalle Valo
2023-11-04 8:57 ` [PATCH v2 2/3] wifi: rt2x00: disable RTS threshold for rt2800 by default Shiji Yang
2023-11-04 8:58 ` [PATCH v2 3/3] wifi: rt2x00: restart beacon queue when hardware reset Shiji Yang
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for read-only IMAP folder(s) and NNTP newsgroup(s).