* [v4 0/6] arm64: dts: ti: k3-j7200: Add properties and sync with uboot
@ 2023-06-11 11:11 Udit Kumar
2023-06-11 11:11 ` [v4 1/6] arm64: dts: ti: k3-j7200: Add general purpose timers Udit Kumar
` (7 more replies)
0 siblings, 8 replies; 9+ messages in thread
From: Udit Kumar @ 2023-06-11 11:11 UTC (permalink / raw
To: nm, vigneshr, kristo, robh+dt, krzysztof.kozlowski+dt,
linux-arm-kernel, devicetree, linux-kernel, conor+dt, m-chawdhry,
n-francis
Cc: Udit Kumar
In continuation of patch series posted by Nishanth for sync of uboot device tree with kernel device tree for AM64 SOC.
https://lore.kernel.org/linux-arm-kernel/20230414073328.381336-1-nm@ti.com/
This series extend device tree sync/clean up for J7200 SOC.
This patch series build on top of
https://lore.kernel.org/all/20230419040007.3022780-1-u-kumar1@ti.com
Boot logs
https://gist.github.com/uditkumarti/a43decc11c49d59c658cfc4f3f255c5e
Changes since v3:
https://lore.kernel.org/all/20230604045525.1889083-1-u-kumar1@ti.com/
* Add general purpose timers
Added reviewed by Tony Lindgren
* Configure pinctrl for timer IO pads
No change
* remove duplicate main_i2c0 pin mux
Moved before uart pin mux
* Add uart pinmux
Added missing uart pin mux
* Define aliases at board level
* Drop SoC level aliases
Moved aliases<F4> at board level
Changes since v2:
https://lore.kernel.org/all/20230601093744.1565802-1-u-kumar1@ti.com/
* Configure pinctrl for timer IO pads
Added reviewed by Tony Lindgren
* Add uart pin mux in main_pmx0
Changed subject of patch
Changes since v1:
https://lore.kernel.org/all/20230426103219.1565266-1-u-kumar1@ti.com/
* Add general purpose timers:
Addded CLKSEL_VD clock for odd numbered timers
Marked MCU_Timer as reserved, fixed clock index for main_timer13
*Configure pinctrl for timer IO pads
Marked mcu_timerio_input as reserved
*main_pmx0 clean up
Splitted into two patches, One for UART and second for i2c duplication removal
*Add uart pin mux in wkup_pmx0
No change
*Add bootph-pre-ram for u-boot
patch dropped, later will add bootph-pre-ram property later for all nodes.
Udit Kumar (6):
arm64: dts: ti: k3-j7200: Add general purpose timers
arm64: dts: ti: k3-j7200: Configure pinctrl for timer IO pads
arm64: dts: ti: k3-j7200-common-proc-board: remove duplicate main_i2c0
pin mux
arm64: dts: ti: k3-j7200-common-proc-board: Add uart pinmux
arm64: dts: ti: k3-j7200-common-proc-board: Define aliases at board
level
arm64: dts: ti: k3-j7200: Drop SoC level aliases
.../dts/ti/k3-j7200-common-proc-board.dts | 67 ++++-
arch/arm64/boot/dts/ti/k3-j7200-main.dtsi | 258 ++++++++++++++++++
.../boot/dts/ti/k3-j7200-mcu-wakeup.dtsi | 150 ++++++++++
arch/arm64/boot/dts/ti/k3-j7200.dtsi | 17 --
4 files changed, 471 insertions(+), 21 deletions(-)
--
2.34.1
^ permalink raw reply [flat|nested] 9+ messages in thread
* [v4 1/6] arm64: dts: ti: k3-j7200: Add general purpose timers
2023-06-11 11:11 [v4 0/6] arm64: dts: ti: k3-j7200: Add properties and sync with uboot Udit Kumar
@ 2023-06-11 11:11 ` Udit Kumar
2023-06-11 11:11 ` [v4 2/6] arm64: dts: ti: k3-j7200: Configure pinctrl for timer IO pads Udit Kumar
` (6 subsequent siblings)
7 siblings, 0 replies; 9+ messages in thread
From: Udit Kumar @ 2023-06-11 11:11 UTC (permalink / raw
To: nm, vigneshr, kristo, robh+dt, krzysztof.kozlowski+dt,
linux-arm-kernel, devicetree, linux-kernel, conor+dt, m-chawdhry,
n-francis
Cc: Udit Kumar, Tony Lindgren
There are 20 general purpose timers on j721e that can be used for
things like PWM using pwm-omap-dmtimer driver. There are also
additional ten timers in the MCU domain which are meant for MCU
firmware usage and hence marked reserved by default.
The odd numbered timers have the option of being cascaded to even
timers to create a 64 bit non-atomic counter which is racy in simple
usage, hence the clock muxes are explicitly setup to individual 32 bit
counters driven off system crystal (HFOSC) as default.
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
---
arch/arm64/boot/dts/ti/k3-j7200-main.dtsi | 240 ++++++++++++++++++
.../boot/dts/ti/k3-j7200-mcu-wakeup.dtsi | 130 ++++++++++
2 files changed, 370 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
index ef352e32f19d..c6b15aceea82 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
@@ -971,6 +971,246 @@ watchdog1: watchdog@2210000 {
assigned-clock-parents = <&k3_clks 253 5>;
};
+ main_timer0: timer@2400000 {
+ compatible = "ti,am654-timer";
+ reg = <0x00 0x2400000 0x00 0x400>;
+ interrupts = <GIC_SPI 224 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&k3_clks 49 1>;
+ clock-names = "fck";
+ assigned-clocks = <&k3_clks 49 1>;
+ assigned-clock-parents = <&k3_clks 49 2>;
+ power-domains = <&k3_pds 49 TI_SCI_PD_EXCLUSIVE>;
+ ti,timer-pwm;
+ };
+
+ main_timer1: timer@2410000 {
+ compatible = "ti,am654-timer";
+ reg = <0x00 0x2410000 0x00 0x400>;
+ interrupts = <GIC_SPI 225 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&k3_clks 50 1>;
+ clock-names = "fck";
+ assigned-clocks = <&k3_clks 50 1>, <&k3_clks 313 0>;
+ assigned-clock-parents = <&k3_clks 50 2>, <&k3_clks 313 1>;
+ power-domains = <&k3_pds 50 TI_SCI_PD_EXCLUSIVE>;
+ ti,timer-pwm;
+ };
+
+ main_timer2: timer@2420000 {
+ compatible = "ti,am654-timer";
+ reg = <0x00 0x2420000 0x00 0x400>;
+ interrupts = <GIC_SPI 226 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&k3_clks 51 1>;
+ clock-names = "fck";
+ assigned-clocks = <&k3_clks 51 1>;
+ assigned-clock-parents = <&k3_clks 51 2>;
+ power-domains = <&k3_pds 49 TI_SCI_PD_EXCLUSIVE>;
+ ti,timer-pwm;
+ };
+
+ main_timer3: timer@2430000 {
+ compatible = "ti,am654-timer";
+ reg = <0x00 0x2430000 0x00 0x400>;
+ interrupts = <GIC_SPI 227 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&k3_clks 52 1>;
+ clock-names = "fck";
+ assigned-clocks = <&k3_clks 52 1>, <&k3_clks 314 0>;
+ assigned-clock-parents = <&k3_clks 52 2>, <&k3_clks 314 1>;
+ power-domains = <&k3_pds 52 TI_SCI_PD_EXCLUSIVE>;
+ ti,timer-pwm;
+ };
+
+ main_timer4: timer@2440000 {
+ compatible = "ti,am654-timer";
+ reg = <0x00 0x2440000 0x00 0x400>;
+ interrupts = <GIC_SPI 228 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&k3_clks 53 1>;
+ clock-names = "fck";
+ assigned-clocks = <&k3_clks 53 1>;
+ assigned-clock-parents = <&k3_clks 53 2>;
+ power-domains = <&k3_pds 53 TI_SCI_PD_EXCLUSIVE>;
+ ti,timer-pwm;
+ };
+
+ main_timer5: timer@2450000 {
+ compatible = "ti,am654-timer";
+ reg = <0x00 0x2450000 0x00 0x400>;
+ interrupts = <GIC_SPI 229 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&k3_clks 54 1>;
+ clock-names = "fck";
+ assigned-clocks = <&k3_clks 54 1>, <&k3_clks 315 0>;
+ assigned-clock-parents = <&k3_clks 54 2>, <&k3_clks 315 1>;
+ power-domains = <&k3_pds 54 TI_SCI_PD_EXCLUSIVE>;
+ ti,timer-pwm;
+ };
+
+ main_timer6: timer@2460000 {
+ compatible = "ti,am654-timer";
+ reg = <0x00 0x2460000 0x00 0x400>;
+ interrupts = <GIC_SPI 230 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&k3_clks 55 1>;
+ clock-names = "fck";
+ assigned-clocks = <&k3_clks 55 1>;
+ assigned-clock-parents = <&k3_clks 55 2>;
+ power-domains = <&k3_pds 55 TI_SCI_PD_EXCLUSIVE>;
+ ti,timer-pwm;
+ };
+
+ main_timer7: timer@2470000 {
+ compatible = "ti,am654-timer";
+ reg = <0x00 0x2470000 0x00 0x400>;
+ interrupts = <GIC_SPI 231 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&k3_clks 57 1>;
+ clock-names = "fck";
+ assigned-clocks = <&k3_clks 57 1>, <&k3_clks 316 0>;
+ assigned-clock-parents = <&k3_clks 57 2>, <&k3_clks 316 1>;
+ power-domains = <&k3_pds 57 TI_SCI_PD_EXCLUSIVE>;
+ ti,timer-pwm;
+ };
+
+ main_timer8: timer@2480000 {
+ compatible = "ti,am654-timer";
+ reg = <0x00 0x2480000 0x00 0x400>;
+ interrupts = <GIC_SPI 232 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&k3_clks 58 1>;
+ clock-names = "fck";
+ assigned-clocks = <&k3_clks 58 1>;
+ assigned-clock-parents = <&k3_clks 58 2>;
+ power-domains = <&k3_pds 58 TI_SCI_PD_EXCLUSIVE>;
+ ti,timer-pwm;
+ };
+
+ main_timer9: timer@2490000 {
+ compatible = "ti,am654-timer";
+ reg = <0x00 0x2490000 0x00 0x400>;
+ interrupts = <GIC_SPI 233 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&k3_clks 59 1>;
+ clock-names = "fck";
+ assigned-clocks = <&k3_clks 59 1>, <&k3_clks 317 0>;
+ assigned-clock-parents = <&k3_clks 59 2>, <&k3_clks 317 1>;
+ power-domains = <&k3_pds 59 TI_SCI_PD_EXCLUSIVE>;
+ ti,timer-pwm;
+ };
+
+ main_timer10: timer@24a0000 {
+ compatible = "ti,am654-timer";
+ reg = <0x00 0x24a0000 0x00 0x400>;
+ interrupts = <GIC_SPI 234 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&k3_clks 60 1>;
+ clock-names = "fck";
+ assigned-clocks = <&k3_clks 60 1>;
+ assigned-clock-parents = <&k3_clks 60 2>;
+ power-domains = <&k3_pds 60 TI_SCI_PD_EXCLUSIVE>;
+ ti,timer-pwm;
+ };
+
+ main_timer11: timer@24b0000 {
+ compatible = "ti,am654-timer";
+ reg = <0x00 0x24b0000 0x00 0x400>;
+ interrupts = <GIC_SPI 235 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&k3_clks 62 1>;
+ clock-names = "fck";
+ assigned-clocks = <&k3_clks 62 1>, <&k3_clks 318 0>;
+ assigned-clock-parents = <&k3_clks 62 2>, <&k3_clks 318 1>;
+ power-domains = <&k3_pds 62 TI_SCI_PD_EXCLUSIVE>;
+ ti,timer-pwm;
+ };
+
+ main_timer12: timer@24c0000 {
+ compatible = "ti,am654-timer";
+ reg = <0x00 0x24c0000 0x00 0x400>;
+ interrupts = <GIC_SPI 236 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&k3_clks 63 1>;
+ clock-names = "fck";
+ assigned-clocks = <&k3_clks 63 1>;
+ assigned-clock-parents = <&k3_clks 63 2>;
+ power-domains = <&k3_pds 63 TI_SCI_PD_EXCLUSIVE>;
+ ti,timer-pwm;
+ };
+
+ main_timer13: timer@24d0000 {
+ compatible = "ti,am654-timer";
+ reg = <0x00 0x24d0000 0x00 0x400>;
+ interrupts = <GIC_SPI 237 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&k3_clks 64 1>;
+ clock-names = "fck";
+ assigned-clocks = <&k3_clks 64 1>, <&k3_clks 319 0>;
+ assigned-clock-parents = <&k3_clks 64 2>, <&k3_clks 319 1>;
+ power-domains = <&k3_pds 64 TI_SCI_PD_EXCLUSIVE>;
+ ti,timer-pwm;
+ };
+
+ main_timer14: timer@24e0000 {
+ compatible = "ti,am654-timer";
+ reg = <0x00 0x24e0000 0x00 0x400>;
+ interrupts = <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&k3_clks 65 1>;
+ clock-names = "fck";
+ assigned-clocks = <&k3_clks 65 1>;
+ assigned-clock-parents = <&k3_clks 65 2>;
+ power-domains = <&k3_pds 65 TI_SCI_PD_EXCLUSIVE>;
+ ti,timer-pwm;
+ };
+
+ main_timer15: timer@24f0000 {
+ compatible = "ti,am654-timer";
+ reg = <0x00 0x24f0000 0x00 0x400>;
+ interrupts = <GIC_SPI 239 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&k3_clks 66 1>;
+ clock-names = "fck";
+ assigned-clocks = <&k3_clks 66 1>, <&k3_clks 320 0>;
+ assigned-clock-parents = <&k3_clks 66 2>, <&k3_clks 320 1>;
+ power-domains = <&k3_pds 66 TI_SCI_PD_EXCLUSIVE>;
+ ti,timer-pwm;
+ };
+
+ main_timer16: timer@2500000 {
+ compatible = "ti,am654-timer";
+ reg = <0x00 0x2500000 0x00 0x400>;
+ interrupts = <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&k3_clks 67 1>;
+ clock-names = "fck";
+ assigned-clocks = <&k3_clks 67 1>;
+ assigned-clock-parents = <&k3_clks 67 2>;
+ power-domains = <&k3_pds 67 TI_SCI_PD_EXCLUSIVE>;
+ ti,timer-pwm;
+ };
+
+ main_timer17: timer@2510000 {
+ compatible = "ti,am654-timer";
+ reg = <0x00 0x2510000 0x00 0x400>;
+ interrupts = <GIC_SPI 241 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&k3_clks 68 1>;
+ clock-names = "fck";
+ assigned-clocks = <&k3_clks 68 1>, <&k3_clks 321 0>;
+ assigned-clock-parents = <&k3_clks 68 2>, <&k3_clks 321 1>;
+ power-domains = <&k3_pds 68 TI_SCI_PD_EXCLUSIVE>;
+ ti,timer-pwm;
+ };
+
+ main_timer18: timer@2520000 {
+ compatible = "ti,am654-timer";
+ reg = <0x00 0x2520000 0x00 0x400>;
+ interrupts = <GIC_SPI 242 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&k3_clks 69 1>;
+ clock-names = "fck";
+ assigned-clocks = <&k3_clks 69 1>;
+ assigned-clock-parents = <&k3_clks 69 2>;
+ power-domains = <&k3_pds 69 TI_SCI_PD_EXCLUSIVE>;
+ ti,timer-pwm;
+ };
+
+ main_timer19: timer@2530000 {
+ compatible = "ti,am654-timer";
+ reg = <0x00 0x2530000 0x00 0x400>;
+ interrupts = <GIC_SPI 243 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&k3_clks 70 1>;
+ clock-names = "fck";
+ assigned-clocks = <&k3_clks 70 1>, <&k3_clks 322 0>;
+ assigned-clock-parents = <&k3_clks 70 2>, <&k3_clks 322 1>;
+ power-domains = <&k3_pds 70 TI_SCI_PD_EXCLUSIVE>;
+ ti,timer-pwm;
+ };
+
main_r5fss0: r5fss@5c00000 {
compatible = "ti,j7200-r5fss";
ti,cluster-mode = <1>;
diff --git a/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi
index 674e695ef844..dcb6696cff17 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi
@@ -34,6 +34,136 @@ k3_reset: reset-controller {
};
};
+ mcu_timer0: timer@40400000 {
+ status = "reserved";
+ compatible = "ti,am654-timer";
+ reg = <0x00 0x40400000 0x00 0x400>;
+ interrupts = <GIC_SPI 816 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&k3_clks 35 1>;
+ clock-names = "fck";
+ assigned-clocks = <&k3_clks 35 1>;
+ assigned-clock-parents = <&k3_clks 35 2>;
+ power-domains = <&k3_pds 35 TI_SCI_PD_EXCLUSIVE>;
+ ti,timer-pwm;
+ };
+
+ mcu_timer1: timer@40410000 {
+ status = "reserved";
+ compatible = "ti,am654-timer";
+ reg = <0x00 0x40410000 0x00 0x400>;
+ interrupts = <GIC_SPI 817 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&k3_clks 71 1>;
+ clock-names = "fck";
+ assigned-clocks = <&k3_clks 71 1>, <&k3_clks 308 0>;
+ assigned-clock-parents = <&k3_clks 71 2>, <&k3_clks 308 1>;
+ power-domains = <&k3_pds 71 TI_SCI_PD_EXCLUSIVE>;
+ ti,timer-pwm;
+ };
+
+ mcu_timer2: timer@40420000 {
+ status = "reserved";
+ compatible = "ti,am654-timer";
+ reg = <0x00 0x40420000 0x00 0x400>;
+ interrupts = <GIC_SPI 818 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&k3_clks 72 1>;
+ clock-names = "fck";
+ assigned-clocks = <&k3_clks 72 1>;
+ assigned-clock-parents = <&k3_clks 72 2>;
+ power-domains = <&k3_pds 72 TI_SCI_PD_EXCLUSIVE>;
+ ti,timer-pwm;
+ };
+
+ mcu_timer3: timer@40430000 {
+ status = "reserved";
+ compatible = "ti,am654-timer";
+ reg = <0x00 0x40430000 0x00 0x400>;
+ interrupts = <GIC_SPI 819 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&k3_clks 73 1>;
+ clock-names = "fck";
+ assigned-clocks = <&k3_clks 73 1>, <&k3_clks 309 0>;
+ assigned-clock-parents = <&k3_clks 73 2>, <&k3_clks 309 1>;
+ power-domains = <&k3_pds 73 TI_SCI_PD_EXCLUSIVE>;
+ ti,timer-pwm;
+ };
+
+ mcu_timer4: timer@40440000 {
+ status = "reserved";
+ compatible = "ti,am654-timer";
+ reg = <0x00 0x40440000 0x00 0x400>;
+ interrupts = <GIC_SPI 820 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&k3_clks 74 1>;
+ clock-names = "fck";
+ assigned-clocks = <&k3_clks 74 1>;
+ assigned-clock-parents = <&k3_clks 74 2>;
+ power-domains = <&k3_pds 74 TI_SCI_PD_EXCLUSIVE>;
+ ti,timer-pwm;
+ };
+
+ mcu_timer5: timer@40450000 {
+ status = "reserved";
+ compatible = "ti,am654-timer";
+ reg = <0x00 0x40450000 0x00 0x400>;
+ interrupts = <GIC_SPI 821 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&k3_clks 75 1>;
+ clock-names = "fck";
+ assigned-clocks = <&k3_clks 75 1>, <&k3_clks 310 0>;
+ assigned-clock-parents = <&k3_clks 75 2>, <&k3_clks 310 1>;
+ power-domains = <&k3_pds 75 TI_SCI_PD_EXCLUSIVE>;
+ ti,timer-pwm;
+ };
+
+ mcu_timer6: timer@40460000 {
+ status = "reserved";
+ compatible = "ti,am654-timer";
+ reg = <0x00 0x40460000 0x00 0x400>;
+ interrupts = <GIC_SPI 822 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&k3_clks 76 1>;
+ clock-names = "fck";
+ assigned-clocks = <&k3_clks 76 1>;
+ assigned-clock-parents = <&k3_clks 76 2>;
+ power-domains = <&k3_pds 35 TI_SCI_PD_EXCLUSIVE>;
+ ti,timer-pwm;
+ };
+
+ mcu_timer7: timer@40470000 {
+ status = "reserved";
+ compatible = "ti,am654-timer";
+ reg = <0x00 0x40470000 0x00 0x400>;
+ interrupts = <GIC_SPI 823 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&k3_clks 77 1>;
+ clock-names = "fck";
+ assigned-clocks = <&k3_clks 77 1>, <&k3_clks 311 0>;
+ assigned-clock-parents = <&k3_clks 77 2>, <&k3_clks 311 1>;
+ power-domains = <&k3_pds 77 TI_SCI_PD_EXCLUSIVE>;
+ ti,timer-pwm;
+ };
+
+ mcu_timer8: timer@40480000 {
+ status = "reserved";
+ compatible = "ti,am654-timer";
+ reg = <0x00 0x40480000 0x00 0x400>;
+ interrupts = <GIC_SPI 824 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&k3_clks 78 1>;
+ clock-names = "fck";
+ assigned-clocks = <&k3_clks 78 1>;
+ assigned-clock-parents = <&k3_clks 78 2>;
+ power-domains = <&k3_pds 78 TI_SCI_PD_EXCLUSIVE>;
+ ti,timer-pwm;
+ };
+
+ mcu_timer9: timer@40490000 {
+ status = "reserved";
+ compatible = "ti,am654-timer";
+ reg = <0x00 0x40490000 0x00 0x400>;
+ interrupts = <GIC_SPI 825 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&k3_clks 79 1>;
+ clock-names = "fck";
+ assigned-clocks = <&k3_clks 79 1>, <&k3_clks 312 0>;
+ assigned-clock-parents = <&k3_clks 79 2>, <&k3_clks 312 1>;
+ power-domains = <&k3_pds 79 TI_SCI_PD_EXCLUSIVE>;
+ ti,timer-pwm;
+ };
+
mcu_conf: syscon@40f00000 {
compatible = "syscon", "simple-mfd";
reg = <0x00 0x40f00000 0x00 0x20000>;
--
2.34.1
^ permalink raw reply related [flat|nested] 9+ messages in thread
* [v4 2/6] arm64: dts: ti: k3-j7200: Configure pinctrl for timer IO pads
2023-06-11 11:11 [v4 0/6] arm64: dts: ti: k3-j7200: Add properties and sync with uboot Udit Kumar
2023-06-11 11:11 ` [v4 1/6] arm64: dts: ti: k3-j7200: Add general purpose timers Udit Kumar
@ 2023-06-11 11:11 ` Udit Kumar
2023-06-11 11:11 ` [v4 3/6] arm64: dts: ti: k3-j7200-common-proc-board: remove duplicate main_i2c0 pin mux Udit Kumar
` (5 subsequent siblings)
7 siblings, 0 replies; 9+ messages in thread
From: Udit Kumar @ 2023-06-11 11:11 UTC (permalink / raw
To: nm, vigneshr, kristo, robh+dt, krzysztof.kozlowski+dt,
linux-arm-kernel, devicetree, linux-kernel, conor+dt, m-chawdhry,
n-francis
Cc: Udit Kumar, Tony Lindgren
There are timer IO pads in the MCU domain, and in the MAIN domain. These
pads can be muxed for the related timers.
There are timer IO control registers for input and output. The registers
for CTRLMMR_TIMER*_CTRL and CTRLMMR_MCU_TIMER*_CTRL are used to control
the input. The registers for CTCTRLMMR_TIMERIO*_CTRL and
CTRLMMR_MCU_TIMERIO*_CTRL the output.
The multiplexing is documented in TRM "5.1.2.3.1.4 Timer IO Muxing Control
Registers" and "5.1.3.3.1.5 Timer IO Muxing Control Registers", and the
CASCADE_EN bit is documented in TRM "12.6.3.1 Timers Overview".
For chaining timers, the timer IO control registers also have a CASCADE_EN
input bit in the CTRLMMR_TIMER*_CTRL in the registers. The CASCADE_EN bit
muxes the previous timer output, or possibly and external TIMER_IO pad
source, to the input clock of the selected timer instance for odd numered
timers. For the even numbered timers, the CASCADE_EN bit does not do
anything. The timer cascade input routing options are shown in TRM
"Figure 12-3224. Timers Overview". For handling beyond multiplexing, the
driver support for timer cascading should be likely be handled via the
clock framework.
The MCU timer controls are also marked as reserved for
usage by the MCU firmware.
Cc: Nishanth Menon <nm@ti.com>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
---
arch/arm64/boot/dts/ti/k3-j7200-main.dtsi | 18 +++++++++++++++++
.../boot/dts/ti/k3-j7200-mcu-wakeup.dtsi | 20 +++++++++++++++++++
2 files changed, 38 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
index c6b15aceea82..a9b3bf8a5c6a 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
@@ -392,6 +392,24 @@ cpts@3d000 {
};
};
+ /* TIMERIO pad input CTRLMMR_TIMER*_CTRL registers */
+ main_timerio_input: pinctrl@104200 {
+ compatible = "pinctrl-single";
+ reg = <0x0 0x104200 0x0 0x50>;
+ #pinctrl-cells = <1>;
+ pinctrl-single,register-width = <32>;
+ pinctrl-single,function-mask = <0x000001ff>;
+ };
+
+ /* TIMERIO pad output CTCTRLMMR_TIMERIO*_CTRL registers */
+ main_timerio_output: pinctrl@104280 {
+ compatible = "pinctrl-single";
+ reg = <0x0 0x104280 0x0 0x20>;
+ #pinctrl-cells = <1>;
+ pinctrl-single,register-width = <32>;
+ pinctrl-single,function-mask = <0x0000001f>;
+ };
+
main_pmx0: pinctrl@11c000 {
compatible = "pinctrl-single";
/* Proxy 0 addressing */
diff --git a/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi
index dcb6696cff17..b518ec9eea32 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi
@@ -183,6 +183,26 @@ chipid@43000014 {
reg = <0x00 0x43000014 0x00 0x4>;
};
+ /* MCU_TIMERIO pad input CTRLMMR_MCU_TIMER*_CTRL registers */
+ mcu_timerio_input: pinctrl@40f04200 {
+ compatible = "pinctrl-single";
+ reg = <0x0 0x40f04200 0x0 0x28>;
+ #pinctrl-cells = <1>;
+ pinctrl-single,register-width = <32>;
+ pinctrl-single,function-mask = <0x0000000F>;
+ status = "reserved";
+ };
+
+ /* MCU_TIMERIO pad output CTRLMMR_MCU_TIMERIO*_CTRL registers */
+ mcu_timerio_output: pinctrl@40f04280 {
+ compatible = "pinctrl-single";
+ reg = <0x0 0x40f04280 0x0 0x28>;
+ #pinctrl-cells = <1>;
+ pinctrl-single,register-width = <32>;
+ pinctrl-single,function-mask = <0x0000000F>;
+ status = "reserved";
+ };
+
wkup_pmx0: pinctrl@4301c000 {
compatible = "pinctrl-single";
/* Proxy 0 addressing */
--
2.34.1
^ permalink raw reply related [flat|nested] 9+ messages in thread
* [v4 3/6] arm64: dts: ti: k3-j7200-common-proc-board: remove duplicate main_i2c0 pin mux
2023-06-11 11:11 [v4 0/6] arm64: dts: ti: k3-j7200: Add properties and sync with uboot Udit Kumar
2023-06-11 11:11 ` [v4 1/6] arm64: dts: ti: k3-j7200: Add general purpose timers Udit Kumar
2023-06-11 11:11 ` [v4 2/6] arm64: dts: ti: k3-j7200: Configure pinctrl for timer IO pads Udit Kumar
@ 2023-06-11 11:11 ` Udit Kumar
2023-06-11 11:11 ` [v4 4/6] arm64: dts: ti: k3-j7200-common-proc-board: Add uart pinmux Udit Kumar
` (4 subsequent siblings)
7 siblings, 0 replies; 9+ messages in thread
From: Udit Kumar @ 2023-06-11 11:11 UTC (permalink / raw
To: nm, vigneshr, kristo, robh+dt, krzysztof.kozlowski+dt,
linux-arm-kernel, devicetree, linux-kernel, conor+dt, m-chawdhry,
n-francis
Cc: Udit Kumar
main_i2c0 pin mux was duplicated in som and common file.
So removing duplicated node from common file.
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
---
arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts | 7 -------
1 file changed, 7 deletions(-)
diff --git a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
index 0cc0e1dc40c5..31b6501443b4 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
@@ -106,13 +106,6 @@ J721E_WKUP_IOPAD(0x0030, PIN_INPUT, 0) /* (L4) MCU_MDIO0_MDIO */
};
&main_pmx0 {
- main_i2c0_pins_default: main-i2c0-pins-default {
- pinctrl-single,pins = <
- J721E_IOPAD(0xd4, PIN_INPUT_PULLUP, 0) /* (V3) I2C0_SCL */
- J721E_IOPAD(0xd8, PIN_INPUT_PULLUP, 0) /* (W2) I2C0_SDA */
- >;
- };
-
main_i2c1_pins_default: main-i2c1-pins-default {
pinctrl-single,pins = <
J721E_IOPAD(0xdc, PIN_INPUT_PULLUP, 3) /* (U3) ECAP0_IN_APWM_OUT.I2C1_SCL */
--
2.34.1
^ permalink raw reply related [flat|nested] 9+ messages in thread
* [v4 4/6] arm64: dts: ti: k3-j7200-common-proc-board: Add uart pinmux
2023-06-11 11:11 [v4 0/6] arm64: dts: ti: k3-j7200: Add properties and sync with uboot Udit Kumar
` (2 preceding siblings ...)
2023-06-11 11:11 ` [v4 3/6] arm64: dts: ti: k3-j7200-common-proc-board: remove duplicate main_i2c0 pin mux Udit Kumar
@ 2023-06-11 11:11 ` Udit Kumar
2023-06-11 11:11 ` [v4 5/6] arm64: dts: ti: k3-j7200-common-proc-board: Define aliases at board level Udit Kumar
` (3 subsequent siblings)
7 siblings, 0 replies; 9+ messages in thread
From: Udit Kumar @ 2023-06-11 11:11 UTC (permalink / raw
To: nm, vigneshr, kristo, robh+dt, krzysztof.kozlowski+dt,
linux-arm-kernel, devicetree, linux-kernel, conor+dt, m-chawdhry,
n-francis
Cc: Udit Kumar
Add main, mcu, wakeup domain uart0 pin mux into common board file and it's
reference to uart node.
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
---
.../dts/ti/k3-j7200-common-proc-board.dts | 58 ++++++++++++++++++-
1 file changed, 57 insertions(+), 1 deletion(-)
diff --git a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
index 31b6501443b4..5569d48b900c 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
@@ -79,6 +79,24 @@ vdd_sd_dv: gpio-regulator-TLV71033 {
};
};
+&wkup_pmx0 {
+ mcu_uart0_pins_default: mcu-uart0-pins-default {
+ pinctrl-single,pins = <
+ J721E_WKUP_IOPAD(0xf4, PIN_INPUT, 0) /* (D20) MCU_UART0_RXD */
+ J721E_WKUP_IOPAD(0xf0, PIN_OUTPUT, 0) /* (D19) MCU_UART0_TXD */
+ J721E_WKUP_IOPAD(0xf8, PIN_INPUT, 0) /* (E20) MCU_UART0_CTSn */
+ J721E_WKUP_IOPAD(0xfc, PIN_OUTPUT, 0) /* (E21) MCU_UART0_RTSn */
+ >;
+ };
+
+ wkup_uart0_pins_default: wkup-uart0-pins-default {
+ pinctrl-single,pins = <
+ J721E_WKUP_IOPAD(0xb0, PIN_INPUT, 0) /* (B14) WKUP_UART0_RXD */
+ J721E_WKUP_IOPAD(0xb4, PIN_OUTPUT, 0) /* (A14) WKUP_UART0_TXD */
+ >;
+ };
+};
+
&wkup_pmx2 {
mcu_cpsw_pins_default: mcu-cpsw-pins-default {
pinctrl-single,pins = <
@@ -106,6 +124,29 @@ J721E_WKUP_IOPAD(0x0030, PIN_INPUT, 0) /* (L4) MCU_MDIO0_MDIO */
};
&main_pmx0 {
+ main_uart0_pins_default: main-uart0-pins-default {
+ pinctrl-single,pins = <
+ J721E_IOPAD(0xb0, PIN_INPUT, 0) /* (T16) UART0_RXD */
+ J721E_IOPAD(0xb4, PIN_OUTPUT, 0) /* (T17) UART0_TXD */
+ J721E_IOPAD(0xc0, PIN_INPUT, 2) /* (W3) SPI0_CS0.UART0_CTSn */
+ J721E_IOPAD(0xc4, PIN_OUTPUT, 2) /* (U5) SPI0_CS1.UART0_RTSn */
+ >;
+ };
+
+ main_uart1_pins_default: main-uart1-pins-default {
+ pinctrl-single,pins = <
+ J721E_IOPAD(0xb8, PIN_INPUT, 0) /* (T18) UART1_RXD */
+ J721E_IOPAD(0xbc, PIN_INPUT, 0) /* (T20) UART1_TXD */
+ >;
+ };
+
+ main_uart3_pins_default: main-uart3-pins-default {
+ pinctrl-single,pins = <
+ J721E_IOPAD(0x60, PIN_INPUT, 11) /* (T15) MCAN8_TX.UART3_CTSn */
+ J721E_IOPAD(0x30, PIN_INPUT, 11) /* (Y18) MCAN2_TX.UART3_RXD */
+ >;
+ };
+
main_i2c1_pins_default: main-i2c1-pins-default {
pinctrl-single,pins = <
J721E_IOPAD(0xdc, PIN_INPUT_PULLUP, 3) /* (U3) ECAP0_IN_APWM_OUT.I2C1_SCL */
@@ -144,22 +185,30 @@ J721E_IOPAD(0x04, PIN_OUTPUT, 0) /* (T4) USB0_DRVVBUS */
&wkup_uart0 {
/* Wakeup UART is used by System firmware */
status = "reserved";
+ pinctrl-names = "default";
+ pinctrl-0 = <&wkup_uart0_pins_default>;
};
&mcu_uart0 {
status = "okay";
- /* Default pinmux */
+ pinctrl-names = "default";
+ pinctrl-0 = <&mcu_uart0_pins_default>;
+ clock-frequency = <96000000>;
};
&main_uart0 {
status = "okay";
/* Shared with ATF on this platform */
power-domains = <&k3_pds 146 TI_SCI_PD_SHARED>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_uart0_pins_default>;
};
&main_uart1 {
status = "okay";
/* Default pinmux */
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_uart1_pins_default>;
};
&main_uart2 {
@@ -167,6 +216,13 @@ &main_uart2 {
status = "reserved";
};
+&main_uart3 {
+ /* Shared with MCAN Interface */
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_uart3_pins_default>;
+};
+
&main_gpio2 {
status = "disabled";
};
--
2.34.1
^ permalink raw reply related [flat|nested] 9+ messages in thread
* [v4 5/6] arm64: dts: ti: k3-j7200-common-proc-board: Define aliases at board level
2023-06-11 11:11 [v4 0/6] arm64: dts: ti: k3-j7200: Add properties and sync with uboot Udit Kumar
` (3 preceding siblings ...)
2023-06-11 11:11 ` [v4 4/6] arm64: dts: ti: k3-j7200-common-proc-board: Add uart pinmux Udit Kumar
@ 2023-06-11 11:11 ` Udit Kumar
2023-06-11 11:11 ` [v4 6/6] arm64: dts: ti: k3-j7200: Drop SoC level aliases Udit Kumar
` (2 subsequent siblings)
7 siblings, 0 replies; 9+ messages in thread
From: Udit Kumar @ 2023-06-11 11:11 UTC (permalink / raw
To: nm, vigneshr, kristo, robh+dt, krzysztof.kozlowski+dt,
linux-arm-kernel, devicetree, linux-kernel, conor+dt, m-chawdhry,
n-francis
Cc: Udit Kumar
Define aliases at board level
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
---
arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts | 10 ++++++++++
1 file changed, 10 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
index 5569d48b900c..38b48115ed0d 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
@@ -15,6 +15,16 @@ / {
compatible = "ti,j7200-evm", "ti,j7200";
model = "Texas Instruments J7200 EVM";
+ aliases {
+ serial0 = &wkup_uart0;
+ serial1 = &mcu_uart0;
+ serial2 = &main_uart0;
+ serial3 = &main_uart1;
+ serial5 = &main_uart3;
+ mmc0 = &main_sdhci0;
+ mmc1 = &main_sdhci1;
+ };
+
chosen {
stdout-path = "serial2:115200n8";
};
--
2.34.1
^ permalink raw reply related [flat|nested] 9+ messages in thread
* [v4 6/6] arm64: dts: ti: k3-j7200: Drop SoC level aliases
2023-06-11 11:11 [v4 0/6] arm64: dts: ti: k3-j7200: Add properties and sync with uboot Udit Kumar
` (4 preceding siblings ...)
2023-06-11 11:11 ` [v4 5/6] arm64: dts: ti: k3-j7200-common-proc-board: Define aliases at board level Udit Kumar
@ 2023-06-11 11:11 ` Udit Kumar
2023-06-13 11:56 ` [v4 0/6] arm64: dts: ti: k3-j7200: Add properties and sync with uboot Nishanth Menon
2023-06-15 13:31 ` Vignesh Raghavendra
7 siblings, 0 replies; 9+ messages in thread
From: Udit Kumar @ 2023-06-11 11:11 UTC (permalink / raw
To: nm, vigneshr, kristo, robh+dt, krzysztof.kozlowski+dt,
linux-arm-kernel, devicetree, linux-kernel, conor+dt, m-chawdhry,
n-francis
Cc: Udit Kumar
Aiases are defined at board level, so dropping from soc level
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
---
arch/arm64/boot/dts/ti/k3-j7200.dtsi | 17 -----------------
1 file changed, 17 deletions(-)
diff --git a/arch/arm64/boot/dts/ti/k3-j7200.dtsi b/arch/arm64/boot/dts/ti/k3-j7200.dtsi
index f1836ec8e934..5ea869014bbc 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j7200.dtsi
@@ -18,23 +18,6 @@ / {
#address-cells = <2>;
#size-cells = <2>;
- aliases {
- serial0 = &wkup_uart0;
- serial1 = &mcu_uart0;
- serial2 = &main_uart0;
- serial3 = &main_uart1;
- serial4 = &main_uart2;
- serial5 = &main_uart3;
- serial6 = &main_uart4;
- serial7 = &main_uart5;
- serial8 = &main_uart6;
- serial9 = &main_uart7;
- serial10 = &main_uart8;
- serial11 = &main_uart9;
- mmc0 = &main_sdhci0;
- mmc1 = &main_sdhci1;
- };
-
chosen { };
cpus {
--
2.34.1
^ permalink raw reply related [flat|nested] 9+ messages in thread
* Re: [v4 0/6] arm64: dts: ti: k3-j7200: Add properties and sync with uboot
2023-06-11 11:11 [v4 0/6] arm64: dts: ti: k3-j7200: Add properties and sync with uboot Udit Kumar
` (5 preceding siblings ...)
2023-06-11 11:11 ` [v4 6/6] arm64: dts: ti: k3-j7200: Drop SoC level aliases Udit Kumar
@ 2023-06-13 11:56 ` Nishanth Menon
2023-06-15 13:31 ` Vignesh Raghavendra
7 siblings, 0 replies; 9+ messages in thread
From: Nishanth Menon @ 2023-06-13 11:56 UTC (permalink / raw
To: Udit Kumar
Cc: vigneshr, kristo, robh+dt, krzysztof.kozlowski+dt,
linux-arm-kernel, devicetree, linux-kernel, conor+dt, m-chawdhry,
n-francis
On 16:41-20230611, Udit Kumar wrote:
> In continuation of patch series posted by Nishanth for sync of uboot device tree with kernel device tree for AM64 SOC.
> https://lore.kernel.org/linux-arm-kernel/20230414073328.381336-1-nm@ti.com/
>
> This series extend device tree sync/clean up for J7200 SOC.
Thank you for the cleanup. For the series:
Reviewed-by: Nishanth Menon <nm@ti.com>
--
Regards,
Nishanth Menon
Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3 1A34 DDB5 849D 1736 249D
^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: [v4 0/6] arm64: dts: ti: k3-j7200: Add properties and sync with uboot
2023-06-11 11:11 [v4 0/6] arm64: dts: ti: k3-j7200: Add properties and sync with uboot Udit Kumar
` (6 preceding siblings ...)
2023-06-13 11:56 ` [v4 0/6] arm64: dts: ti: k3-j7200: Add properties and sync with uboot Nishanth Menon
@ 2023-06-15 13:31 ` Vignesh Raghavendra
7 siblings, 0 replies; 9+ messages in thread
From: Vignesh Raghavendra @ 2023-06-15 13:31 UTC (permalink / raw
To: nm, kristo, robh+dt, krzysztof.kozlowski+dt, linux-arm-kernel,
devicetree, linux-kernel, conor+dt, m-chawdhry, n-francis,
Udit Kumar
Cc: Vignesh Raghavendra
Hi Udit Kumar,
On Sun, 11 Jun 2023 16:41:34 +0530, Udit Kumar wrote:
> In continuation of patch series posted by Nishanth for sync of uboot device tree with kernel device tree for AM64 SOC.
> https://lore.kernel.org/linux-arm-kernel/20230414073328.381336-1-nm@ti.com/
>
> This series extend device tree sync/clean up for J7200 SOC.
>
> This patch series build on top of
> https://lore.kernel.org/all/20230419040007.3022780-1-u-kumar1@ti.com
>
> [...]
I have applied the following to branch ti-k3-dts-next on [1].
Thank you!
[1/6] arm64: dts: ti: k3-j7200: Add general purpose timers
commit: c8a28ed4837ce03254e0941f4fbc8364b1e78543
[2/6] arm64: dts: ti: k3-j7200: Configure pinctrl for timer IO pads
commit: 03612d384621ffe21c6d338de916251d1bfd84fa
[3/6] arm64: dts: ti: k3-j7200-common-proc-board: remove duplicate main_i2c0 pin mux
commit: 7f58e2b418d89f38f242b04da5a1dd93a2c514fd
[4/6] arm64: dts: ti: k3-j7200-common-proc-board: Add uart pinmux
commit: 3709ea7f960ed77ac29af692c9e32351060400d9
[5/6] arm64: dts: ti: k3-j7200-common-proc-board: Define aliases at board level
commit: c4ba159fff90791956370ce93c130aadea87dbb6
[6/6] arm64: dts: ti: k3-j7200: Drop SoC level aliases
commit: 858dde8a3f56f0b7a0c217ac4abf56e34c34ae74
All being well this means that it will be integrated into the linux-next
tree (usually sometime in the next 24 hours) and sent up the chain during
the next merge window (or sooner if it is a relevant bug fix), however if
problems are discovered then the patch may be dropped or reverted.
You may get further e-mails resulting from automated or manual testing
and review of the tree, please engage with people reporting problems and
send followup patches addressing any issues that are reported if needed.
If any updates are required or you are submitting further changes they
should be sent as incremental updates against current git, existing
patches will not be replaced.
Please add any relevant lists and maintainers to the CCs when replying
to this mail.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/ti/linux.git
--
Vignesh
^ permalink raw reply [flat|nested] 9+ messages in thread
end of thread, other threads:[~2023-06-15 13:32 UTC | newest]
Thread overview: 9+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2023-06-11 11:11 [v4 0/6] arm64: dts: ti: k3-j7200: Add properties and sync with uboot Udit Kumar
2023-06-11 11:11 ` [v4 1/6] arm64: dts: ti: k3-j7200: Add general purpose timers Udit Kumar
2023-06-11 11:11 ` [v4 2/6] arm64: dts: ti: k3-j7200: Configure pinctrl for timer IO pads Udit Kumar
2023-06-11 11:11 ` [v4 3/6] arm64: dts: ti: k3-j7200-common-proc-board: remove duplicate main_i2c0 pin mux Udit Kumar
2023-06-11 11:11 ` [v4 4/6] arm64: dts: ti: k3-j7200-common-proc-board: Add uart pinmux Udit Kumar
2023-06-11 11:11 ` [v4 5/6] arm64: dts: ti: k3-j7200-common-proc-board: Define aliases at board level Udit Kumar
2023-06-11 11:11 ` [v4 6/6] arm64: dts: ti: k3-j7200: Drop SoC level aliases Udit Kumar
2023-06-13 11:56 ` [v4 0/6] arm64: dts: ti: k3-j7200: Add properties and sync with uboot Nishanth Menon
2023-06-15 13:31 ` Vignesh Raghavendra
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for read-only IMAP folder(s) and NNTP newsgroup(s).