From: Fei Shao <fshao@chromium.org>
To: Chen-Yu Tsai <wenst@chromium.org>
Cc: Rob Herring <robh+dt@kernel.org>,
Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
Conor Dooley <conor+dt@kernel.org>,
Mark Brown <broonie@kernel.org>,
Liam Girdwood <lgirdwood@gmail.com>,
Matthias Brugger <matthias.bgg@gmail.com>,
AngeloGioacchino Del Regno
<angelogioacchino.delregno@collabora.com>,
devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org,
linux-mediatek@lists.infradead.org, linux-kernel@vger.kernel.org
Subject: Re: [PATCH 3/9] regulator: mt6358: Merge VCN33_* regulators
Date: Mon, 12 Jun 2023 18:56:57 +0800 [thread overview]
Message-ID: <CAJ66y9H91WaRxaZzXRYc5LN9t+M+ZpEy6nbgo=W1kOn_Yu_BCg@mail.gmail.com> (raw)
In-Reply-To: <20230609083009.2822259-4-wenst@chromium.org>
On Fri, Jun 9, 2023 at 4:30 PM Chen-Yu Tsai <wenst@chromium.org> wrote:
>
> The VCN33_BT and VCN33_WIFI regulators are actually the same regulator,
> having the same voltage setting and output pin. There are simply two
> enable bits that are ORed together to enable the regulator.
>
> Having two regulators representing the same output pin is misleading
> from a design matching standpoint, and also error-prone in driver
> implementations. If consumers try to set different voltages on either
> regulator, the one set later would override the one set before. There
> are ways around this, such as chaining them together and having the
> downstream one act as a switch. But given there's only one output pin,
> such a workaround doesn't match reality.
>
> Remove the VCN33_WIFI regulator. During the probe phase, have the driver
> sync the enable status of VCN33_WIFI to VCN33_BT. Also drop the suffix
> so that the regulator name matches the pin name in the datasheet.
>
> Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
> ---
> drivers/regulator/mt6358-regulator.c | 65 +++++++++++++++++-----
> include/linux/regulator/mt6358-regulator.h | 6 +-
> 2 files changed, 52 insertions(+), 19 deletions(-)
>
> diff --git a/drivers/regulator/mt6358-regulator.c b/drivers/regulator/mt6358-regulator.c
> index c9e16bd092f6..faf6b0757019 100644
> --- a/drivers/regulator/mt6358-regulator.c
> +++ b/drivers/regulator/mt6358-regulator.c
> @@ -277,7 +277,7 @@ static const unsigned int vcama_voltages[] = {
> 2800000, 2900000, 3000000,
> };
>
> -static const unsigned int vcn33_bt_wifi_voltages[] = {
> +static const unsigned int vcn33_voltages[] = {
> 3300000, 3400000, 3500000,
> };
>
> @@ -321,7 +321,7 @@ static const u32 vcama_idx[] = {
> 0, 7, 9, 10, 11, 12,
> };
>
> -static const u32 vcn33_bt_wifi_idx[] = {
> +static const u32 vcn33_idx[] = {
> 1, 2, 3,
> };
>
> @@ -566,12 +566,8 @@ static struct mt6358_regulator_info mt6358_regulators[] = {
> MT6358_LDO_VCAMA1_CON0, 0, MT6358_VCAMA1_ANA_CON0, 0xf00),
> MT6358_LDO("ldo_vemc", VEMC, vmch_vemc_voltages, vmch_vemc_idx,
> MT6358_LDO_VEMC_CON0, 0, MT6358_VEMC_ANA_CON0, 0x700),
> - MT6358_LDO("ldo_vcn33_bt", VCN33_BT, vcn33_bt_wifi_voltages,
> - vcn33_bt_wifi_idx, MT6358_LDO_VCN33_CON0_0,
> - 0, MT6358_VCN33_ANA_CON0, 0x300),
> - MT6358_LDO("ldo_vcn33_wifi", VCN33_WIFI, vcn33_bt_wifi_voltages,
> - vcn33_bt_wifi_idx, MT6358_LDO_VCN33_CON0_1,
> - 0, MT6358_VCN33_ANA_CON0, 0x300),
> + MT6358_LDO("ldo_vcn33", VCN33, vcn33_voltages, vcn33_idx,
> + MT6358_LDO_VCN33_CON0_0, 0, MT6358_VCN33_ANA_CON0, 0x300),
> MT6358_LDO("ldo_vcama2", VCAMA2, vcama_voltages, vcama_idx,
> MT6358_LDO_VCAMA2_CON0, 0, MT6358_VCAMA2_ANA_CON0, 0xf00),
> MT6358_LDO("ldo_vmc", VMC, vmc_voltages, vmc_idx,
> @@ -662,12 +658,8 @@ static struct mt6358_regulator_info mt6366_regulators[] = {
> MT6358_LDO_VMCH_CON0, 0, MT6358_VMCH_ANA_CON0, 0x700),
> MT6366_LDO("ldo_vemc", VEMC, vmch_vemc_voltages, vmch_vemc_idx,
> MT6358_LDO_VEMC_CON0, 0, MT6358_VEMC_ANA_CON0, 0x700),
> - MT6366_LDO("ldo_vcn33_bt", VCN33_BT, vcn33_bt_wifi_voltages,
> - vcn33_bt_wifi_idx, MT6358_LDO_VCN33_CON0_0,
> - 0, MT6358_VCN33_ANA_CON0, 0x300),
> - MT6366_LDO("ldo_vcn33_wifi", VCN33_WIFI, vcn33_bt_wifi_voltages,
> - vcn33_bt_wifi_idx, MT6358_LDO_VCN33_CON0_1,
> - 0, MT6358_VCN33_ANA_CON0, 0x300),
> + MT6366_LDO("ldo_vcn33", VCN33, vcn33_voltages, vcn33_idx,
> + MT6358_LDO_VCN33_CON0_0, 0, MT6358_VCN33_ANA_CON0, 0x300),
> MT6366_LDO("ldo_vmc", VMC, vmc_voltages, vmc_idx,
> MT6358_LDO_VMC_CON0, 0, MT6358_VMC_ANA_CON0, 0xf00),
> MT6366_LDO("ldo_vsim2", VSIM2, vsim_voltages, vsim_idx,
> @@ -690,13 +682,56 @@ static struct mt6358_regulator_info mt6366_regulators[] = {
> MT6358_LDO_VSRAM_CON1, 0x7f),
> };
>
> +static int mt6358_sync_vcn33_setting(struct device *dev)
> +{
> + struct mt6397_chip *mt6397 = dev_get_drvdata(dev->parent);
> + unsigned int val;
> + int ret;
> +
> + /*
> + * VCN33_WIFI and VCN33_BT are two separate enable bits for the same
> + * regulator. They share the same voltage setting and output pin.
> + * Instead of having two potentially conflicting regulators, just have
> + * one VCN33 regulator. Sync the two enable bits and only use one in
> + * the regulator device.
> + */
> + ret = regmap_read(mt6397->regmap, MT6358_LDO_VCN33_CON0_1, &val);
> + if (ret) {
> + dev_err(dev, "Failed to read VCN33_WIFI setting\n");
> + return ret;
> + }
> +
> + if (!(val & BIT(0)))
> + return 0;
> +
> + /* Sync VCN33_WIFI enable status to VCN33_BT */
> + ret = regmap_update_bits(mt6397->regmap, MT6358_LDO_VCN33_CON0_0, BIT(0), BIT(0));
> + if (ret) {
> + dev_err(dev, "Failed to sync VCN33_WIFI setting to VCN33_BT\n");
> + return ret;
> + }
> +
> + /* Disable VCN33_WIFI */
> + ret = regmap_update_bits(mt6397->regmap, MT6358_LDO_VCN33_CON0_1, BIT(0), 0);
> + if (ret) {
> + dev_err(dev, "Failed to disable VCN33_BT\n");
I think it should be "VCN33_WIFI" in the error message?
Regards,
Fei
next prev parent reply other threads:[~2023-06-12 11:09 UTC|newest]
Thread overview: 32+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-06-09 8:29 [PATCH 0/9] regulator: mt6358: Remove bogus regulators and improvements Chen-Yu Tsai
2023-06-09 8:29 ` [PATCH 1/9] regulator: dt-bindings: mt6358: Merge ldo_vcn33_* regulators Chen-Yu Tsai
2023-06-09 15:47 ` Matthias Brugger
2023-06-09 16:02 ` Krzysztof Kozlowski
2023-06-09 8:29 ` [PATCH 2/9] regulator: dt-bindings: mt6358: Drop *_sshub regulators Chen-Yu Tsai
2023-06-09 15:47 ` Matthias Brugger
2023-06-09 16:02 ` Krzysztof Kozlowski
2023-06-09 8:30 ` [PATCH 3/9] regulator: mt6358: Merge VCN33_* regulators Chen-Yu Tsai
2023-06-09 8:58 ` AngeloGioacchino Del Regno
2023-06-12 3:41 ` Chen-Yu Tsai
2023-06-09 15:56 ` Conor Dooley
2023-06-10 15:28 ` Conor Dooley
2023-06-12 4:19 ` Chen-Yu Tsai
2023-06-12 17:34 ` Conor Dooley
2023-06-12 10:56 ` Fei Shao [this message]
2023-06-15 7:37 ` Chen-Yu Tsai
2023-06-09 8:30 ` [PATCH 4/9] regulator: mt6358: Drop *_SSHUB regulators Chen-Yu Tsai
2023-06-09 9:03 ` AngeloGioacchino Del Regno
2023-06-12 4:45 ` Chen-Yu Tsai
2023-06-12 18:13 ` Mark Brown
2023-06-14 7:39 ` AngeloGioacchino Del Regno
2023-06-09 15:52 ` Matthias Brugger
2023-06-09 8:30 ` [PATCH 5/9] regulator: mt6358: Const-ify mt6358_regulator_info data structures Chen-Yu Tsai
2023-06-09 8:30 ` [PATCH 6/9] regulator: mt6358: Use linear voltage helpers for single range regulators Chen-Yu Tsai
2023-06-09 8:30 ` [PATCH 7/9] regulator: mt6358: Add output voltage fine tuning to fixed regulators Chen-Yu Tsai
2023-06-09 10:03 ` AngeloGioacchino Del Regno
2023-06-14 16:14 ` Mark Brown
2023-06-15 3:24 ` Chen-Yu Tsai
2023-06-09 8:30 ` [PATCH 8/9] regulator: mt6358: Add output voltage fine tuning to variable LDOs Chen-Yu Tsai
2023-06-09 10:03 ` AngeloGioacchino Del Regno
2023-06-09 8:30 ` [PATCH 9/9] arm64: dts: mediatek: mt6358: Merge ldo_vcn33_* regulators Chen-Yu Tsai
2023-06-14 18:58 ` (subset) [PATCH 0/9] regulator: mt6358: Remove bogus regulators and improvements Mark Brown
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to='CAJ66y9H91WaRxaZzXRYc5LN9t+M+ZpEy6nbgo=W1kOn_Yu_BCg@mail.gmail.com' \
--to=fshao@chromium.org \
--cc=angelogioacchino.delregno@collabora.com \
--cc=broonie@kernel.org \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=krzysztof.kozlowski+dt@linaro.org \
--cc=lgirdwood@gmail.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mediatek@lists.infradead.org \
--cc=matthias.bgg@gmail.com \
--cc=robh+dt@kernel.org \
--cc=wenst@chromium.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for read-only IMAP folder(s) and NNTP newsgroup(s).