From: Mark Brown <broonie@kernel.org>
To: Wenyou Yang <wenyou.yang@atmel.com>, Mark Brown <broonie@kernel.org>
Cc: linux-kernel@vger.kernel.org
Subject: Applied "regulator: act8945a: add regulator driver for ACT8945A" to the regulator tree
Date: Fri, 05 Feb 2016 18:58:28 +0000 [thread overview]
Message-ID: <E1aRlaO-0004GI-20@debutante> (raw)
In-Reply-To: <1454646811-19472-2-git-send-email-wenyou.yang@atmel.com>
The patch
regulator: act8945a: add regulator driver for ACT8945A
has been applied to the regulator tree at
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator.git
All being well this means that it will be integrated into the linux-next
tree (usually sometime in the next 24 hours) and sent to Linus during
the next merge window (or sooner if it is a bug fix), however if
problems are discovered then the patch may be dropped or reverted.
You may get further e-mails resulting from automated or manual testing
and review of the tree, please engage with people reporting problems and
send followup patches addressing any issues that are reported if needed.
If any updates are required or you are submitting further changes they
should be sent as incremental updates against current git, existing
patches will not be replaced.
Please add any relevant lists and maintainers to the CCs when replying
to this mail.
Thanks,
Mark
>From 38c09961048b853afd9429c9b57685a1511bc857 Mon Sep 17 00:00:00 2001
From: Wenyou Yang <wenyou.yang@atmel.com>
Date: Fri, 5 Feb 2016 12:33:30 +0800
Subject: [PATCH] regulator: act8945a: add regulator driver for ACT8945A
This patch adds new regulator driver to support ACT8945A MFD
chip's regulators.
The ACT8945A has three step-down DC/DC converters and four
low-dropout regulators.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
---
drivers/regulator/Kconfig | 9 ++
drivers/regulator/Makefile | 1 +
drivers/regulator/act8945a-regulator.c | 165 +++++++++++++++++++++++++++++++++
3 files changed, 175 insertions(+)
create mode 100644 drivers/regulator/act8945a-regulator.c
diff --git a/drivers/regulator/Kconfig b/drivers/regulator/Kconfig
index 8155e80dd3f8..74a6354eaefa 100644
--- a/drivers/regulator/Kconfig
+++ b/drivers/regulator/Kconfig
@@ -78,6 +78,15 @@ config REGULATOR_ACT8865
This driver controls a active-semi act8865 voltage output
regulator via I2C bus.
+config REGULATOR_ACT8945A
+ tristate "Active-semi ACT8945A voltage regulator"
+ depends on MFD_ACT8945A
+ help
+ This driver controls a active-semi ACT8945A voltage regulator
+ via I2C bus. The ACT8945A features three step-down DC/DC converters
+ and four low-dropout linear regulators, along with a ActivePath
+ battery charger.
+
config REGULATOR_AD5398
tristate "Analog Devices AD5398/AD5821 regulators"
depends on I2C
diff --git a/drivers/regulator/Makefile b/drivers/regulator/Makefile
index 980b1943fa81..348cfd727350 100644
--- a/drivers/regulator/Makefile
+++ b/drivers/regulator/Makefile
@@ -15,6 +15,7 @@ obj-$(CONFIG_REGULATOR_AAT2870) += aat2870-regulator.o
obj-$(CONFIG_REGULATOR_AB3100) += ab3100.o
obj-$(CONFIG_REGULATOR_AB8500) += ab8500-ext.o ab8500.o
obj-$(CONFIG_REGULATOR_ACT8865) += act8865-regulator.o
+obj-$(CONFIG_REGULATOR_ACT8945A) += act8945a-regulator.o
obj-$(CONFIG_REGULATOR_AD5398) += ad5398.o
obj-$(CONFIG_REGULATOR_ANATOP) += anatop-regulator.o
obj-$(CONFIG_REGULATOR_ARIZONA) += arizona-micsupp.o arizona-ldo1.o
diff --git a/drivers/regulator/act8945a-regulator.c b/drivers/regulator/act8945a-regulator.c
new file mode 100644
index 000000000000..441864b9fece
--- /dev/null
+++ b/drivers/regulator/act8945a-regulator.c
@@ -0,0 +1,165 @@
+/*
+ * Voltage regulation driver for active-semi ACT8945A PMIC
+ *
+ * Copyright (C) 2015 Atmel Corporation
+ *
+ * Author: Wenyou Yang <wenyou.yang@atmel.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ */
+
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include <linux/regulator/driver.h>
+#include <linux/regulator/machine.h>
+
+/**
+ * ACT8945A Global Register Map.
+ */
+#define ACT8945A_SYS_MODE 0x00
+#define ACT8945A_SYS_CTRL 0x01
+#define ACT8945A_DCDC1_VSET1 0x20
+#define ACT8945A_DCDC1_VSET2 0x21
+#define ACT8945A_DCDC1_CTRL 0x22
+#define ACT8945A_DCDC2_VSET1 0x30
+#define ACT8945A_DCDC2_VSET2 0x31
+#define ACT8945A_DCDC2_CTRL 0x32
+#define ACT8945A_DCDC3_VSET1 0x40
+#define ACT8945A_DCDC3_VSET2 0x41
+#define ACT8945A_DCDC3_CTRL 0x42
+#define ACT8945A_LDO1_VSET 0x50
+#define ACT8945A_LDO1_CTRL 0x51
+#define ACT8945A_LDO2_VSET 0x54
+#define ACT8945A_LDO2_CTRL 0x55
+#define ACT8945A_LDO3_VSET 0x60
+#define ACT8945A_LDO3_CTRL 0x61
+#define ACT8945A_LDO4_VSET 0x64
+#define ACT8945A_LDO4_CTRL 0x65
+
+/**
+ * Field Definitions.
+ */
+#define ACT8945A_ENA 0x80 /* ON - [7] */
+#define ACT8945A_VSEL_MASK 0x3F /* VSET - [5:0] */
+
+/**
+ * ACT8945A Voltage Number
+ */
+#define ACT8945A_VOLTAGE_NUM 64
+
+enum {
+ ACT8945A_ID_DCDC1,
+ ACT8945A_ID_DCDC2,
+ ACT8945A_ID_DCDC3,
+ ACT8945A_ID_LDO1,
+ ACT8945A_ID_LDO2,
+ ACT8945A_ID_LDO3,
+ ACT8945A_ID_LDO4,
+ ACT8945A_REG_NUM,
+};
+
+static const struct regulator_linear_range act8945a_voltage_ranges[] = {
+ REGULATOR_LINEAR_RANGE(600000, 0, 23, 25000),
+ REGULATOR_LINEAR_RANGE(1200000, 24, 47, 50000),
+ REGULATOR_LINEAR_RANGE(2400000, 48, 63, 100000),
+};
+
+static struct regulator_ops act8945a_ops = {
+ .list_voltage = regulator_list_voltage_linear_range,
+ .map_voltage = regulator_map_voltage_linear_range,
+ .get_voltage_sel = regulator_get_voltage_sel_regmap,
+ .set_voltage_sel = regulator_set_voltage_sel_regmap,
+ .enable = regulator_enable_regmap,
+ .disable = regulator_disable_regmap,
+ .is_enabled = regulator_is_enabled_regmap,
+};
+
+#define ACT89xx_REG(_name, _family, _id, _vsel_reg, _supply) \
+ [_family##_ID_##_id] = { \
+ .name = _name, \
+ .supply_name = _supply, \
+ .of_match = of_match_ptr("REG_"#_id), \
+ .regulators_node = of_match_ptr("regulators"), \
+ .id = _family##_ID_##_id, \
+ .type = REGULATOR_VOLTAGE, \
+ .ops = &act8945a_ops, \
+ .n_voltages = ACT8945A_VOLTAGE_NUM, \
+ .linear_ranges = act8945a_voltage_ranges, \
+ .n_linear_ranges = ARRAY_SIZE(act8945a_voltage_ranges), \
+ .vsel_reg = _family##_##_id##_##_vsel_reg, \
+ .vsel_mask = ACT8945A_VSEL_MASK, \
+ .enable_reg = _family##_##_id##_CTRL, \
+ .enable_mask = ACT8945A_ENA, \
+ .owner = THIS_MODULE, \
+ }
+
+static const struct regulator_desc act8945a_regulators[] = {
+ ACT89xx_REG("DCDC_REG1", ACT8945A, DCDC1, VSET1, "vp1"),
+ ACT89xx_REG("DCDC_REG2", ACT8945A, DCDC2, VSET1, "vp2"),
+ ACT89xx_REG("DCDC_REG3", ACT8945A, DCDC3, VSET1, "vp3"),
+ ACT89xx_REG("LDO_REG1", ACT8945A, LDO1, VSET, "inl45"),
+ ACT89xx_REG("LDO_REG2", ACT8945A, LDO2, VSET, "inl45"),
+ ACT89xx_REG("LDO_REG3", ACT8945A, LDO3, VSET, "inl67"),
+ ACT89xx_REG("LDO_REG4", ACT8945A, LDO4, VSET, "inl67"),
+};
+
+static const struct regulator_desc act8945a_alt_regulators[] = {
+ ACT89xx_REG("DCDC_REG1", ACT8945A, DCDC1, VSET2, "vp1"),
+ ACT89xx_REG("DCDC_REG2", ACT8945A, DCDC2, VSET2, "vp2"),
+ ACT89xx_REG("DCDC_REG3", ACT8945A, DCDC3, VSET2, "vp3"),
+ ACT89xx_REG("LDO_REG1", ACT8945A, LDO1, VSET, "inl45"),
+ ACT89xx_REG("LDO_REG2", ACT8945A, LDO2, VSET, "inl45"),
+ ACT89xx_REG("LDO_REG3", ACT8945A, LDO3, VSET, "inl67"),
+ ACT89xx_REG("LDO_REG4", ACT8945A, LDO4, VSET, "inl67"),
+};
+
+static int act8945a_pmic_probe(struct platform_device *pdev)
+{
+ struct regulator_config config = { };
+ const struct regulator_desc *regulators;
+ struct regulator_dev *rdev;
+ int i, num_regulators;
+ bool voltage_select;
+
+ voltage_select = of_property_read_bool(pdev->dev.parent->of_node,
+ "active-semi,vsel-high");
+
+ if (voltage_select) {
+ regulators = act8945a_alt_regulators;
+ num_regulators = ARRAY_SIZE(act8945a_alt_regulators);
+ } else {
+ regulators = act8945a_regulators;
+ num_regulators = ARRAY_SIZE(act8945a_regulators);
+ }
+
+ config.dev = &pdev->dev;
+ config.dev->of_node = pdev->dev.parent->of_node;
+ for (i = 0; i < num_regulators; i++) {
+ rdev = devm_regulator_register(&pdev->dev, ®ulators[i], &config);
+ if (IS_ERR(rdev)) {
+ dev_err(&pdev->dev,
+ "failed to register %s regulator\n",
+ regulators[i].name);
+ return PTR_ERR(rdev);
+ }
+ }
+
+ return 0;
+}
+
+static struct platform_driver act8945a_pmic_driver = {
+ .driver = {
+ .name = "act8945a-regulator",
+ },
+ .probe = act8945a_pmic_probe,
+};
+module_platform_driver(act8945a_pmic_driver);
+
+MODULE_DESCRIPTION("Active-semi ACT8945A voltage regulator driver");
+MODULE_AUTHOR("Wenyou Yang <wenyou.yang@atmel.com>");
+MODULE_LICENSE("GPL");
--
2.7.0.rc3
next prev parent reply other threads:[~2016-02-05 18:58 UTC|newest]
Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-02-05 4:33 [PATCH v5 0/2] regulator: act8945a: add regulator driver for the sub-device of ACT8945A MFD Wenyou Yang
2016-02-05 4:33 ` [PATCH v5 1/2] regulator: act8945a: add regulator driver for ACT8945A Wenyou Yang
2016-02-05 18:58 ` Mark Brown [this message]
2016-02-05 4:33 ` [PATCH v5 2/2] regulator: add documentation for ACT8945A's regulator DT bindings Wenyou Yang
2016-02-05 18:58 ` Applied "regulator: add documentation for ACT8945A's regulator DT bindings" to the regulator tree Mark Brown
-- strict thread matches above, loose matches on Subject: below --
2016-01-20 6:55 [PATCH v3 1/2] regulator: act8945a: add regulator driver for ACT8945A Wenyou Yang
2016-01-27 18:38 ` Applied "regulator: act8945a: add regulator driver for ACT8945A" to the regulator tree Mark Brown
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=E1aRlaO-0004GI-20@debutante \
--to=broonie@kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=wenyou.yang@atmel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for read-only IMAP folder(s) and NNTP newsgroup(s).