From: Jakub Kicinski <kuba@kernel.org>
To: davem@davemloft.net, pabeni@redhat.com
Cc: netdev@vger.kernel.org, Jakub Kicinski <kuba@kernel.org>,
corbet@lwn.net, linux-doc@vger.kernel.org, mkl@pengutronix.de,
dario.binacchi@amarulasolutions.com, m.chetan.kumar@intel.com,
arnd@arndb.de, juerg.haefliger@canonical.com,
linus.walleij@linaro.org, kilobyte@angband.pl,
lipeng321@huawei.com, huangguangbin2@huawei.com,
Alan Cox <alan@linux.intel.com>
Subject: [PATCH net-next 5/6] net: wan: remove support for Z85230-based devices
Date: Tue, 26 Apr 2022 10:54:35 -0700 [thread overview]
Message-ID: <20220426175436.417283-6-kuba@kernel.org> (raw)
In-Reply-To: <20220426175436.417283-1-kuba@kernel.org>
Looks like all the changes to this driver had been automated
churn since git era begun. The driver is using virt_to_bus(),
it's just a maintenance burden unlikely to have any users.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
---
CC: corbet@lwn.net
CC: linux-doc@vger.kernel.org
CC: mkl@pengutronix.de
CC: dario.binacchi@amarulasolutions.com
CC: m.chetan.kumar@intel.com
CC: arnd@arndb.de
CC: juerg.haefliger@canonical.com
CC: linus.walleij@linaro.org
CC: kilobyte@angband.pl
CC: lipeng321@huawei.com
CC: huangguangbin2@huawei.com
CC: Alan Cox <alan@linux.intel.com>
---
.../networking/device_drivers/index.rst | 1 -
.../networking/device_drivers/wan/index.rst | 18 -
.../device_drivers/wan/z8530book.rst | 256 ---
drivers/net/wan/Kconfig | 22 -
drivers/net/wan/Makefile | 2 -
drivers/net/wan/hostess_sv11.c | 336 ----
drivers/net/wan/sealevel.c | 352 ----
drivers/net/wan/z85230.c | 1641 -----------------
drivers/net/wan/z85230.h | 407 ----
9 files changed, 3035 deletions(-)
delete mode 100644 Documentation/networking/device_drivers/wan/index.rst
delete mode 100644 Documentation/networking/device_drivers/wan/z8530book.rst
delete mode 100644 drivers/net/wan/hostess_sv11.c
delete mode 100644 drivers/net/wan/sealevel.c
delete mode 100644 drivers/net/wan/z85230.c
delete mode 100644 drivers/net/wan/z85230.h
diff --git a/Documentation/networking/device_drivers/index.rst b/Documentation/networking/device_drivers/index.rst
index 5f5cfdb2a300..601eacaf12f3 100644
--- a/Documentation/networking/device_drivers/index.rst
+++ b/Documentation/networking/device_drivers/index.rst
@@ -17,7 +17,6 @@ Hardware Device Drivers
fddi/index
hamradio/index
qlogic/index
- wan/index
wifi/index
wwan/index
diff --git a/Documentation/networking/device_drivers/wan/index.rst b/Documentation/networking/device_drivers/wan/index.rst
deleted file mode 100644
index 9d9ae94f00b4..000000000000
--- a/Documentation/networking/device_drivers/wan/index.rst
+++ /dev/null
@@ -1,18 +0,0 @@
-.. SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
-
-Classic WAN Device Drivers
-==========================
-
-Contents:
-
-.. toctree::
- :maxdepth: 2
-
- z8530book
-
-.. only:: subproject and html
-
- Indices
- =======
-
- * :ref:`genindex`
diff --git a/Documentation/networking/device_drivers/wan/z8530book.rst b/Documentation/networking/device_drivers/wan/z8530book.rst
deleted file mode 100644
index fea2c40e7973..000000000000
--- a/Documentation/networking/device_drivers/wan/z8530book.rst
+++ /dev/null
@@ -1,256 +0,0 @@
-=======================
-Z8530 Programming Guide
-=======================
-
-:Author: Alan Cox
-
-Introduction
-============
-
-The Z85x30 family synchronous/asynchronous controller chips are used on
-a large number of cheap network interface cards. The kernel provides a
-core interface layer that is designed to make it easy to provide WAN
-services using this chip.
-
-The current driver only support synchronous operation. Merging the
-asynchronous driver support into this code to allow any Z85x30 device to
-be used as both a tty interface and as a synchronous controller is a
-project for Linux post the 2.4 release
-
-Driver Modes
-============
-
-The Z85230 driver layer can drive Z8530, Z85C30 and Z85230 devices in
-three different modes. Each mode can be applied to an individual channel
-on the chip (each chip has two channels).
-
-The PIO synchronous mode supports the most common Z8530 wiring. Here the
-chip is interface to the I/O and interrupt facilities of the host
-machine but not to the DMA subsystem. When running PIO the Z8530 has
-extremely tight timing requirements. Doing high speeds, even with a
-Z85230 will be tricky. Typically you should expect to achieve at best
-9600 baud with a Z8C530 and 64Kbits with a Z85230.
-
-The DMA mode supports the chip when it is configured to use dual DMA
-channels on an ISA bus. The better cards tend to support this mode of
-operation for a single channel. With DMA running the Z85230 tops out
-when it starts to hit ISA DMA constraints at about 512Kbits. It is worth
-noting here that many PC machines hang or crash when the chip is driven
-fast enough to hold the ISA bus solid.
-
-Transmit DMA mode uses a single DMA channel. The DMA channel is used for
-transmission as the transmit FIFO is smaller than the receive FIFO. it
-gives better performance than pure PIO mode but is nowhere near as ideal
-as pure DMA mode.
-
-Using the Z85230 driver
-=======================
-
-The Z85230 driver provides the back end interface to your board. To
-configure a Z8530 interface you need to detect the board and to identify
-its ports and interrupt resources. It is also your problem to verify the
-resources are available.
-
-Having identified the chip you need to fill in a struct z8530_dev,
-which describes each chip. This object must exist until you finally
-shutdown the board. Firstly zero the active field. This ensures nothing
-goes off without you intending it. The irq field should be set to the
-interrupt number of the chip. (Each chip has a single interrupt source
-rather than each channel). You are responsible for allocating the
-interrupt line. The interrupt handler should be set to
-:c:func:`z8530_interrupt()`. The device id should be set to the
-z8530_dev structure pointer. Whether the interrupt can be shared or not
-is board dependent, and up to you to initialise.
-
-The structure holds two channel structures. Initialise chanA.ctrlio and
-chanA.dataio with the address of the control and data ports. You can or
-this with Z8530_PORT_SLEEP to indicate your interface needs the 5uS
-delay for chip settling done in software. The PORT_SLEEP option is
-architecture specific. Other flags may become available on future
-platforms, eg for MMIO. Initialise the chanA.irqs to &z8530_nop to
-start the chip up as disabled and discarding interrupt events. This
-ensures that stray interrupts will be mopped up and not hang the bus.
-Set chanA.dev to point to the device structure itself. The private and
-name field you may use as you wish. The private field is unused by the
-Z85230 layer. The name is used for error reporting and it may thus make
-sense to make it match the network name.
-
-Repeat the same operation with the B channel if your chip has both
-channels wired to something useful. This isn't always the case. If it is
-not wired then the I/O values do not matter, but you must initialise
-chanB.dev.
-
-If your board has DMA facilities then initialise the txdma and rxdma
-fields for the relevant channels. You must also allocate the ISA DMA
-channels and do any necessary board level initialisation to configure
-them. The low level driver will do the Z8530 and DMA controller
-programming but not board specific magic.
-
-Having initialised the device you can then call
-:c:func:`z8530_init()`. This will probe the chip and reset it into
-a known state. An identification sequence is then run to identify the
-chip type. If the checks fail to pass the function returns a non zero
-error code. Typically this indicates that the port given is not valid.
-After this call the type field of the z8530_dev structure is
-initialised to either Z8530, Z85C30 or Z85230 according to the chip
-found.
-
-Once you have called z8530_init you can also make use of the utility
-function :c:func:`z8530_describe()`. This provides a consistent
-reporting format for the Z8530 devices, and allows all the drivers to
-provide consistent reporting.
-
-Attaching Network Interfaces
-============================
-
-If you wish to use the network interface facilities of the driver, then
-you need to attach a network device to each channel that is present and
-in use. In addition to use the generic HDLC you need to follow some
-additional plumbing rules. They may seem complex but a look at the
-example hostess_sv11 driver should reassure you.
-
-The network device used for each channel should be pointed to by the
-netdevice field of each channel. The hdlc-> priv field of the network
-device points to your private data - you will need to be able to find
-your private data from this.
-
-The way most drivers approach this particular problem is to create a
-structure holding the Z8530 device definition and put that into the
-private field of the network device. The network device fields of the
-channels then point back to the network devices.
-
-If you wish to use the generic HDLC then you need to register the HDLC
-device.
-
-Before you register your network device you will also need to provide
-suitable handlers for most of the network device callbacks. See the
-network device documentation for more details on this.
-
-Configuring And Activating The Port
-===================================
-
-The Z85230 driver provides helper functions and tables to load the port
-registers on the Z8530 chips. When programming the register settings for
-a channel be aware that the documentation recommends initialisation
-orders. Strange things happen when these are not followed.
-
-:c:func:`z8530_channel_load()` takes an array of pairs of
-initialisation values in an array of u8 type. The first value is the
-Z8530 register number. Add 16 to indicate the alternate register bank on
-the later chips. The array is terminated by a 255.
-
-The driver provides a pair of public tables. The z8530_hdlc_kilostream
-table is for the UK 'Kilostream' service and also happens to cover most
-other end host configurations. The z8530_hdlc_kilostream_85230 table
-is the same configuration using the enhancements of the 85230 chip. The
-configuration loaded is standard NRZ encoded synchronous data with HDLC
-bitstuffing. All of the timing is taken from the other end of the link.
-
-When writing your own tables be aware that the driver internally tracks
-register values. It may need to reload values. You should therefore be
-sure to set registers 1-7, 9-11, 14 and 15 in all configurations. Where
-the register settings depend on DMA selection the driver will update the
-bits itself when you open or close. Loading a new table with the
-interface open is not recommended.
-
-There are three standard configurations supported by the core code. In
-PIO mode the interface is programmed up to use interrupt driven PIO.
-This places high demands on the host processor to avoid latency. The
-driver is written to take account of latency issues but it cannot avoid
-latencies caused by other drivers, notably IDE in PIO mode. Because the
-drivers allocate buffers you must also prevent MTU changes while the
-port is open.
-
-Once the port is open it will call the rx_function of each channel
-whenever a completed packet arrived. This is invoked from interrupt
-context and passes you the channel and a network buffer (struct
-sk_buff) holding the data. The data includes the CRC bytes so most
-users will want to trim the last two bytes before processing the data.
-This function is very timing critical. When you wish to simply discard
-data the support code provides the function
-:c:func:`z8530_null_rx()` to discard the data.
-
-To active PIO mode sending and receiving the ``z8530_sync_open`` is called.
-This expects to be passed the network device and the channel. Typically
-this is called from your network device open callback. On a failure a
-non zero error status is returned.
-The :c:func:`z8530_sync_close()` function shuts down a PIO
-channel. This must be done before the channel is opened again and before
-the driver shuts down and unloads.
-
-The ideal mode of operation is dual channel DMA mode. Here the kernel
-driver will configure the board for DMA in both directions. The driver
-also handles ISA DMA issues such as controller programming and the
-memory range limit for you. This mode is activated by calling the
-:c:func:`z8530_sync_dma_open()` function. On failure a non zero
-error value is returned. Once this mode is activated it can be shut down
-by calling the :c:func:`z8530_sync_dma_close()`. You must call
-the close function matching the open mode you used.
-
-The final supported mode uses a single DMA channel to drive the transmit
-side. As the Z85C30 has a larger FIFO on the receive channel this tends
-to increase the maximum speed a little. This is activated by calling the
-``z8530_sync_txdma_open``. This returns a non zero error code on failure. The
-:c:func:`z8530_sync_txdma_close()` function closes down the Z8530
-interface from this mode.
-
-Network Layer Functions
-=======================
-
-The Z8530 layer provides functions to queue packets for transmission.
-The driver internally buffers the frame currently being transmitted and
-one further frame (in order to keep back to back transmission running).
-Any further buffering is up to the caller.
-
-The function :c:func:`z8530_queue_xmit()` takes a network buffer
-in sk_buff format and queues it for transmission. The caller must
-provide the entire packet with the exception of the bitstuffing and CRC.
-This is normally done by the caller via the generic HDLC interface
-layer. It returns 0 if the buffer has been queued and non zero values
-for queue full. If the function accepts the buffer it becomes property
-of the Z8530 layer and the caller should not free it.
-
-The function :c:func:`z8530_get_stats()` returns a pointer to an
-internally maintained per interface statistics block. This provides most
-of the interface code needed to implement the network layer get_stats
-callback.
-
-Porting The Z8530 Driver
-========================
-
-The Z8530 driver is written to be portable. In DMA mode it makes
-assumptions about the use of ISA DMA. These are probably warranted in
-most cases as the Z85230 in particular was designed to glue to PC type
-machines. The PIO mode makes no real assumptions.
-
-Should you need to retarget the Z8530 driver to another architecture the
-only code that should need changing are the port I/O functions. At the
-moment these assume PC I/O port accesses. This may not be appropriate
-for all platforms. Replacing :c:func:`z8530_read_port()` and
-``z8530_write_port`` is intended to be all that is required to port
-this driver layer.
-
-Known Bugs And Assumptions
-==========================
-
-Interrupt Locking
- The locking in the driver is done via the global cli/sti lock. This
- makes for relatively poor SMP performance. Switching this to use a
- per device spin lock would probably materially improve performance.
-
-Occasional Failures
- We have reports of occasional failures when run for very long
- periods of time and the driver starts to receive junk frames. At the
- moment the cause of this is not clear.
-
-Public Functions Provided
-=========================
-
-.. kernel-doc:: drivers/net/wan/z85230.c
- :export:
-
-Internal Functions
-==================
-
-.. kernel-doc:: drivers/net/wan/z85230.c
- :internal:
diff --git a/drivers/net/wan/Kconfig b/drivers/net/wan/Kconfig
index 12c5b6c67ab2..dcb069dde66b 100644
--- a/drivers/net/wan/Kconfig
+++ b/drivers/net/wan/Kconfig
@@ -23,28 +23,6 @@ menuconfig WAN
if WAN
-# There is no way to detect a comtrol sv11 - force it modular for now.
-config HOSTESS_SV11
- tristate "Comtrol Hostess SV-11 support"
- depends on ISA && m && ISA_DMA_API && INET && HDLC && VIRT_TO_BUS
- help
- Driver for Comtrol Hostess SV-11 network card which
- operates on low speed synchronous serial links at up to
- 256Kbps, supporting PPP and Cisco HDLC.
-
- The driver will be compiled as a module: the
- module will be called hostess_sv11.
-
-# There is no way to detect a Sealevel board. Force it modular
-config SEALEVEL_4021
- tristate "Sealevel Systems 4021 support"
- depends on ISA && m && ISA_DMA_API && INET && HDLC && VIRT_TO_BUS
- help
- This is a driver for the Sealevel Systems ACB 56 serial I/O adapter.
-
- The driver will be compiled as a module: the
- module will be called sealevel.
-
# Generic HDLC
config HDLC
tristate "Generic HDLC layer"
diff --git a/drivers/net/wan/Makefile b/drivers/net/wan/Makefile
index 901a094c061c..5bec8fae47f8 100644
--- a/drivers/net/wan/Makefile
+++ b/drivers/net/wan/Makefile
@@ -14,8 +14,6 @@ obj-$(CONFIG_HDLC_FR) += hdlc_fr.o
obj-$(CONFIG_HDLC_PPP) += hdlc_ppp.o
obj-$(CONFIG_HDLC_X25) += hdlc_x25.o
-obj-$(CONFIG_HOSTESS_SV11) += z85230.o hostess_sv11.o
-obj-$(CONFIG_SEALEVEL_4021) += z85230.o sealevel.o
obj-$(CONFIG_FARSYNC) += farsync.o
obj-$(CONFIG_LAPBETHER) += lapbether.o
diff --git a/drivers/net/wan/hostess_sv11.c b/drivers/net/wan/hostess_sv11.c
deleted file mode 100644
index e985e54ba75d..000000000000
--- a/drivers/net/wan/hostess_sv11.c
+++ /dev/null
@@ -1,336 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/* Comtrol SV11 card driver
- *
- * This is a slightly odd Z85230 synchronous driver. All you need to
- * know basically is
- *
- * Its a genuine Z85230
- *
- * It supports DMA using two DMA channels in SYNC mode. The driver doesn't
- * use these facilities
- *
- * The control port is at io+1, the data at io+3 and turning off the DMA
- * is done by writing 0 to io+4
- *
- * The hardware does the bus handling to avoid the need for delays between
- * touching control registers.
- *
- * Port B isn't wired (why - beats me)
- *
- * Generic HDLC port Copyright (C) 2008 Krzysztof Halasa <khc@pm.waw.pl>
- */
-
-#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
-
-#include <linux/module.h>
-#include <linux/kernel.h>
-#include <linux/mm.h>
-#include <linux/net.h>
-#include <linux/skbuff.h>
-#include <linux/netdevice.h>
-#include <linux/if_arp.h>
-#include <linux/delay.h>
-#include <linux/hdlc.h>
-#include <linux/ioport.h>
-#include <linux/slab.h>
-#include <net/arp.h>
-
-#include <asm/irq.h>
-#include <asm/io.h>
-#include <asm/dma.h>
-#include <asm/byteorder.h>
-#include "z85230.h"
-
-static int dma;
-
-/* Network driver support routines
- */
-
-static inline struct z8530_dev *dev_to_sv(struct net_device *dev)
-{
- return (struct z8530_dev *)dev_to_hdlc(dev)->priv;
-}
-
-/* Frame receive. Simple for our card as we do HDLC and there
- * is no funny garbage involved
- */
-
-static void hostess_input(struct z8530_channel *c, struct sk_buff *skb)
-{
- /* Drop the CRC - it's not a good idea to try and negotiate it ;) */
- skb_trim(skb, skb->len - 2);
- skb->protocol = hdlc_type_trans(skb, c->netdevice);
- skb_reset_mac_header(skb);
- skb->dev = c->netdevice;
- /* Send it to the PPP layer. We don't have time to process
- * it right now.
- */
- netif_rx(skb);
-}
-
-/* We've been placed in the UP state
- */
-
-static int hostess_open(struct net_device *d)
-{
- struct z8530_dev *sv11 = dev_to_sv(d);
- int err = -1;
-
- /* Link layer up
- */
- switch (dma) {
- case 0:
- err = z8530_sync_open(d, &sv11->chanA);
- break;
- case 1:
- err = z8530_sync_dma_open(d, &sv11->chanA);
- break;
- case 2:
- err = z8530_sync_txdma_open(d, &sv11->chanA);
- break;
- }
-
- if (err)
- return err;
-
- err = hdlc_open(d);
- if (err) {
- switch (dma) {
- case 0:
- z8530_sync_close(d, &sv11->chanA);
- break;
- case 1:
- z8530_sync_dma_close(d, &sv11->chanA);
- break;
- case 2:
- z8530_sync_txdma_close(d, &sv11->chanA);
- break;
- }
- return err;
- }
- sv11->chanA.rx_function = hostess_input;
-
- /*
- * Go go go
- */
-
- netif_start_queue(d);
- return 0;
-}
-
-static int hostess_close(struct net_device *d)
-{
- struct z8530_dev *sv11 = dev_to_sv(d);
- /* Discard new frames
- */
- sv11->chanA.rx_function = z8530_null_rx;
-
- hdlc_close(d);
- netif_stop_queue(d);
-
- switch (dma) {
- case 0:
- z8530_sync_close(d, &sv11->chanA);
- break;
- case 1:
- z8530_sync_dma_close(d, &sv11->chanA);
- break;
- case 2:
- z8530_sync_txdma_close(d, &sv11->chanA);
- break;
- }
- return 0;
-}
-
-/* Passed network frames, fire them downwind.
- */
-
-static netdev_tx_t hostess_queue_xmit(struct sk_buff *skb,
- struct net_device *d)
-{
- return z8530_queue_xmit(&dev_to_sv(d)->chanA, skb);
-}
-
-static int hostess_attach(struct net_device *dev, unsigned short encoding,
- unsigned short parity)
-{
- if (encoding == ENCODING_NRZ && parity == PARITY_CRC16_PR1_CCITT)
- return 0;
- return -EINVAL;
-}
-
-/* Description block for a Comtrol Hostess SV11 card
- */
-
-static const struct net_device_ops hostess_ops = {
- .ndo_open = hostess_open,
- .ndo_stop = hostess_close,
- .ndo_start_xmit = hdlc_start_xmit,
- .ndo_siocwandev = hdlc_ioctl,
-};
-
-static struct z8530_dev *sv11_init(int iobase, int irq)
-{
- struct z8530_dev *sv;
- struct net_device *netdev;
- /* Get the needed I/O space
- */
-
- if (!request_region(iobase, 8, "Comtrol SV11")) {
- pr_warn("I/O 0x%X already in use\n", iobase);
- return NULL;
- }
-
- sv = kzalloc(sizeof(struct z8530_dev), GFP_KERNEL);
- if (!sv)
- goto err_kzalloc;
-
- /* Stuff in the I/O addressing
- */
-
- sv->active = 0;
-
- sv->chanA.ctrlio = iobase + 1;
- sv->chanA.dataio = iobase + 3;
- sv->chanB.ctrlio = -1;
- sv->chanB.dataio = -1;
- sv->chanA.irqs = &z8530_nop;
- sv->chanB.irqs = &z8530_nop;
-
- outb(0, iobase + 4); /* DMA off */
-
- /* We want a fast IRQ for this device. Actually we'd like an even faster
- * IRQ ;) - This is one driver RtLinux is made for
- */
-
- if (request_irq(irq, z8530_interrupt, 0,
- "Hostess SV11", sv) < 0) {
- pr_warn("IRQ %d already in use\n", irq);
- goto err_irq;
- }
-
- sv->irq = irq;
- sv->chanA.private = sv;
- sv->chanA.dev = sv;
- sv->chanB.dev = sv;
-
- if (dma) {
- /* You can have DMA off or 1 and 3 thats the lot
- * on the Comtrol.
- */
- sv->chanA.txdma = 3;
- sv->chanA.rxdma = 1;
- outb(0x03 | 0x08, iobase + 4); /* DMA on */
- if (request_dma(sv->chanA.txdma, "Hostess SV/11 (TX)"))
- goto err_txdma;
-
- if (dma == 1)
- if (request_dma(sv->chanA.rxdma, "Hostess SV/11 (RX)"))
- goto err_rxdma;
- }
-
- /* Kill our private IRQ line the hostess can end up chattering
- * until the configuration is set
- */
- disable_irq(irq);
-
- /* Begin normal initialise
- */
-
- if (z8530_init(sv)) {
- pr_err("Z8530 series device not found\n");
- enable_irq(irq);
- goto free_dma;
- }
- z8530_channel_load(&sv->chanB, z8530_dead_port);
- if (sv->type == Z85C30)
- z8530_channel_load(&sv->chanA, z8530_hdlc_kilostream);
- else
- z8530_channel_load(&sv->chanA, z8530_hdlc_kilostream_85230);
-
- enable_irq(irq);
-
- /* Now we can take the IRQ
- */
-
- sv->chanA.netdevice = netdev = alloc_hdlcdev(sv);
- if (!netdev)
- goto free_dma;
-
- dev_to_hdlc(netdev)->attach = hostess_attach;
- dev_to_hdlc(netdev)->xmit = hostess_queue_xmit;
- netdev->netdev_ops = &hostess_ops;
- netdev->base_addr = iobase;
- netdev->irq = irq;
-
- if (register_hdlc_device(netdev)) {
- pr_err("unable to register HDLC device\n");
- free_netdev(netdev);
- goto free_dma;
- }
-
- z8530_describe(sv, "I/O", iobase);
- sv->active = 1;
- return sv;
-
-free_dma:
- if (dma == 1)
- free_dma(sv->chanA.rxdma);
-err_rxdma:
- if (dma)
- free_dma(sv->chanA.txdma);
-err_txdma:
- free_irq(irq, sv);
-err_irq:
- kfree(sv);
-err_kzalloc:
- release_region(iobase, 8);
- return NULL;
-}
-
-static void sv11_shutdown(struct z8530_dev *dev)
-{
- unregister_hdlc_device(dev->chanA.netdevice);
- z8530_shutdown(dev);
- free_irq(dev->irq, dev);
- if (dma) {
- if (dma == 1)
- free_dma(dev->chanA.rxdma);
- free_dma(dev->chanA.txdma);
- }
- release_region(dev->chanA.ctrlio - 1, 8);
- free_netdev(dev->chanA.netdevice);
- kfree(dev);
-}
-
-static int io = 0x200;
-static int irq = 9;
-
-module_param_hw(io, int, ioport, 0);
-MODULE_PARM_DESC(io, "The I/O base of the Comtrol Hostess SV11 card");
-module_param_hw(dma, int, dma, 0);
-MODULE_PARM_DESC(dma, "Set this to 1 to use DMA1/DMA3 for TX/RX");
-module_param_hw(irq, int, irq, 0);
-MODULE_PARM_DESC(irq, "The interrupt line setting for the Comtrol Hostess SV11 card");
-
-MODULE_AUTHOR("Alan Cox");
-MODULE_LICENSE("GPL");
-MODULE_DESCRIPTION("Modular driver for the Comtrol Hostess SV11");
-
-static struct z8530_dev *sv11_unit;
-
-static int sv11_module_init(void)
-{
- sv11_unit = sv11_init(io, irq);
- if (!sv11_unit)
- return -ENODEV;
- return 0;
-}
-module_init(sv11_module_init);
-
-static void sv11_module_cleanup(void)
-{
- if (sv11_unit)
- sv11_shutdown(sv11_unit);
-}
-module_exit(sv11_module_cleanup);
diff --git a/drivers/net/wan/sealevel.c b/drivers/net/wan/sealevel.c
deleted file mode 100644
index eddd20aab691..000000000000
--- a/drivers/net/wan/sealevel.c
+++ /dev/null
@@ -1,352 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/* Sealevel Systems 4021 driver.
- *
- * (c) Copyright 1999, 2001 Alan Cox
- * (c) Copyright 2001 Red Hat Inc.
- * Generic HDLC port Copyright (C) 2008 Krzysztof Halasa <khc@pm.waw.pl>
- */
-
-#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
-
-#include <linux/module.h>
-#include <linux/kernel.h>
-#include <linux/mm.h>
-#include <linux/net.h>
-#include <linux/skbuff.h>
-#include <linux/netdevice.h>
-#include <linux/if_arp.h>
-#include <linux/delay.h>
-#include <linux/hdlc.h>
-#include <linux/ioport.h>
-#include <linux/init.h>
-#include <linux/slab.h>
-#include <net/arp.h>
-
-#include <asm/irq.h>
-#include <asm/io.h>
-#include <asm/dma.h>
-#include <asm/byteorder.h>
-#include "z85230.h"
-
-struct slvl_device {
- struct z8530_channel *chan;
- int channel;
-};
-
-struct slvl_board {
- struct slvl_device dev[2];
- struct z8530_dev board;
- int iobase;
-};
-
- /* Network driver support routines */
-
-static inline struct slvl_device *dev_to_chan(struct net_device *dev)
-{
- return (struct slvl_device *)dev_to_hdlc(dev)->priv;
-}
-
-/* Frame receive. Simple for our card as we do HDLC and there
- * is no funny garbage involved
- */
-
-static void sealevel_input(struct z8530_channel *c, struct sk_buff *skb)
-{
- /* Drop the CRC - it's not a good idea to try and negotiate it ;) */
- skb_trim(skb, skb->len - 2);
- skb->protocol = hdlc_type_trans(skb, c->netdevice);
- skb_reset_mac_header(skb);
- skb->dev = c->netdevice;
- netif_rx(skb);
-}
-
- /* We've been placed in the UP state */
-
-static int sealevel_open(struct net_device *d)
-{
- struct slvl_device *slvl = dev_to_chan(d);
- int err = -1;
- int unit = slvl->channel;
-
- /* Link layer up. */
-
- switch (unit) {
- case 0:
- err = z8530_sync_dma_open(d, slvl->chan);
- break;
- case 1:
- err = z8530_sync_open(d, slvl->chan);
- break;
- }
-
- if (err)
- return err;
-
- err = hdlc_open(d);
- if (err) {
- switch (unit) {
- case 0:
- z8530_sync_dma_close(d, slvl->chan);
- break;
- case 1:
- z8530_sync_close(d, slvl->chan);
- break;
- }
- return err;
- }
-
- slvl->chan->rx_function = sealevel_input;
-
- netif_start_queue(d);
- return 0;
-}
-
-static int sealevel_close(struct net_device *d)
-{
- struct slvl_device *slvl = dev_to_chan(d);
- int unit = slvl->channel;
-
- /* Discard new frames */
-
- slvl->chan->rx_function = z8530_null_rx;
-
- hdlc_close(d);
- netif_stop_queue(d);
-
- switch (unit) {
- case 0:
- z8530_sync_dma_close(d, slvl->chan);
- break;
- case 1:
- z8530_sync_close(d, slvl->chan);
- break;
- }
- return 0;
-}
-
-/* Passed network frames, fire them downwind. */
-
-static netdev_tx_t sealevel_queue_xmit(struct sk_buff *skb,
- struct net_device *d)
-{
- return z8530_queue_xmit(dev_to_chan(d)->chan, skb);
-}
-
-static int sealevel_attach(struct net_device *dev, unsigned short encoding,
- unsigned short parity)
-{
- if (encoding == ENCODING_NRZ && parity == PARITY_CRC16_PR1_CCITT)
- return 0;
- return -EINVAL;
-}
-
-static const struct net_device_ops sealevel_ops = {
- .ndo_open = sealevel_open,
- .ndo_stop = sealevel_close,
- .ndo_start_xmit = hdlc_start_xmit,
- .ndo_siocwandev = hdlc_ioctl,
-};
-
-static int slvl_setup(struct slvl_device *sv, int iobase, int irq)
-{
- struct net_device *dev = alloc_hdlcdev(sv);
-
- if (!dev)
- return -1;
-
- dev_to_hdlc(dev)->attach = sealevel_attach;
- dev_to_hdlc(dev)->xmit = sealevel_queue_xmit;
- dev->netdev_ops = &sealevel_ops;
- dev->base_addr = iobase;
- dev->irq = irq;
-
- if (register_hdlc_device(dev)) {
- pr_err("unable to register HDLC device\n");
- free_netdev(dev);
- return -1;
- }
-
- sv->chan->netdevice = dev;
- return 0;
-}
-
-/* Allocate and setup Sealevel board. */
-
-static __init struct slvl_board *slvl_init(int iobase, int irq,
- int txdma, int rxdma, int slow)
-{
- struct z8530_dev *dev;
- struct slvl_board *b;
-
- /* Get the needed I/O space */
-
- if (!request_region(iobase, 8, "Sealevel 4021")) {
- pr_warn("I/O 0x%X already in use\n", iobase);
- return NULL;
- }
-
- b = kzalloc(sizeof(struct slvl_board), GFP_KERNEL);
- if (!b)
- goto err_kzalloc;
-
- b->dev[0].chan = &b->board.chanA;
- b->dev[0].channel = 0;
-
- b->dev[1].chan = &b->board.chanB;
- b->dev[1].channel = 1;
-
- dev = &b->board;
-
- /* Stuff in the I/O addressing */
-
- dev->active = 0;
-
- b->iobase = iobase;
-
- /* Select 8530 delays for the old board */
-
- if (slow)
- iobase |= Z8530_PORT_SLEEP;
-
- dev->chanA.ctrlio = iobase + 1;
- dev->chanA.dataio = iobase;
- dev->chanB.ctrlio = iobase + 3;
- dev->chanB.dataio = iobase + 2;
-
- dev->chanA.irqs = &z8530_nop;
- dev->chanB.irqs = &z8530_nop;
-
- /* Assert DTR enable DMA */
-
- outb(3 | (1 << 7), b->iobase + 4);
-
- /* We want a fast IRQ for this device. Actually we'd like an even faster
- * IRQ ;) - This is one driver RtLinux is made for
- */
-
- if (request_irq(irq, z8530_interrupt, 0,
- "SeaLevel", dev) < 0) {
- pr_warn("IRQ %d already in use\n", irq);
- goto err_request_irq;
- }
-
- dev->irq = irq;
- dev->chanA.private = &b->dev[0];
- dev->chanB.private = &b->dev[1];
- dev->chanA.dev = dev;
- dev->chanB.dev = dev;
-
- dev->chanA.txdma = 3;
- dev->chanA.rxdma = 1;
- if (request_dma(dev->chanA.txdma, "SeaLevel (TX)"))
- goto err_dma_tx;
-
- if (request_dma(dev->chanA.rxdma, "SeaLevel (RX)"))
- goto err_dma_rx;
-
- disable_irq(irq);
-
- /* Begin normal initialise */
-
- if (z8530_init(dev) != 0) {
- pr_err("Z8530 series device not found\n");
- enable_irq(irq);
- goto free_hw;
- }
- if (dev->type == Z85C30) {
- z8530_channel_load(&dev->chanA, z8530_hdlc_kilostream);
- z8530_channel_load(&dev->chanB, z8530_hdlc_kilostream);
- } else {
- z8530_channel_load(&dev->chanA, z8530_hdlc_kilostream_85230);
- z8530_channel_load(&dev->chanB, z8530_hdlc_kilostream_85230);
- }
-
- /* Now we can take the IRQ */
-
- enable_irq(irq);
-
- if (slvl_setup(&b->dev[0], iobase, irq))
- goto free_hw;
- if (slvl_setup(&b->dev[1], iobase, irq))
- goto free_netdev0;
-
- z8530_describe(dev, "I/O", iobase);
- dev->active = 1;
- return b;
-
-free_netdev0:
- unregister_hdlc_device(b->dev[0].chan->netdevice);
- free_netdev(b->dev[0].chan->netdevice);
-free_hw:
- free_dma(dev->chanA.rxdma);
-err_dma_rx:
- free_dma(dev->chanA.txdma);
-err_dma_tx:
- free_irq(irq, dev);
-err_request_irq:
- kfree(b);
-err_kzalloc:
- release_region(iobase, 8);
- return NULL;
-}
-
-static void __exit slvl_shutdown(struct slvl_board *b)
-{
- int u;
-
- z8530_shutdown(&b->board);
-
- for (u = 0; u < 2; u++) {
- struct net_device *d = b->dev[u].chan->netdevice;
-
- unregister_hdlc_device(d);
- free_netdev(d);
- }
-
- free_irq(b->board.irq, &b->board);
- free_dma(b->board.chanA.rxdma);
- free_dma(b->board.chanA.txdma);
- /* DMA off on the card, drop DTR */
- outb(0, b->iobase);
- release_region(b->iobase, 8);
- kfree(b);
-}
-
-static int io = 0x238;
-static int txdma = 1;
-static int rxdma = 3;
-static int irq = 5;
-static bool slow;
-
-module_param_hw(io, int, ioport, 0);
-MODULE_PARM_DESC(io, "The I/O base of the Sealevel card");
-module_param_hw(txdma, int, dma, 0);
-MODULE_PARM_DESC(txdma, "Transmit DMA channel");
-module_param_hw(rxdma, int, dma, 0);
-MODULE_PARM_DESC(rxdma, "Receive DMA channel");
-module_param_hw(irq, int, irq, 0);
-MODULE_PARM_DESC(irq, "The interrupt line setting for the SeaLevel card");
-module_param(slow, bool, 0);
-MODULE_PARM_DESC(slow, "Set this for an older Sealevel card such as the 4012");
-
-MODULE_AUTHOR("Alan Cox");
-MODULE_LICENSE("GPL");
-MODULE_DESCRIPTION("Modular driver for the SeaLevel 4021");
-
-static struct slvl_board *slvl_unit;
-
-static int __init slvl_init_module(void)
-{
- slvl_unit = slvl_init(io, irq, txdma, rxdma, slow);
-
- return slvl_unit ? 0 : -ENODEV;
-}
-
-static void __exit slvl_cleanup_module(void)
-{
- if (slvl_unit)
- slvl_shutdown(slvl_unit);
-}
-
-module_init(slvl_init_module);
-module_exit(slvl_cleanup_module);
diff --git a/drivers/net/wan/z85230.c b/drivers/net/wan/z85230.c
deleted file mode 100644
index 982a03488a00..000000000000
--- a/drivers/net/wan/z85230.c
+++ /dev/null
@@ -1,1641 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/* (c) Copyright 1998 Alan Cox <alan@lxorguk.ukuu.org.uk>
- * (c) Copyright 2000, 2001 Red Hat Inc
- *
- * Development of this driver was funded by Equiinet Ltd
- * http://www.equiinet.com
- *
- * ChangeLog:
- *
- * Asynchronous mode dropped for 2.2. For 2.5 we will attempt the
- * unification of all the Z85x30 asynchronous drivers for real.
- *
- * DMA now uses get_free_page as kmalloc buffers may span a 64K
- * boundary.
- *
- * Modified for SMP safety and SMP locking by Alan Cox
- * <alan@lxorguk.ukuu.org.uk>
- *
- * Performance
- *
- * Z85230:
- * Non DMA you want a 486DX50 or better to do 64Kbits. 9600 baud
- * X.25 is not unrealistic on all machines. DMA mode can in theory
- * handle T1/E1 quite nicely. In practice the limit seems to be about
- * 512Kbit->1Mbit depending on motherboard.
- *
- * Z85C30:
- * 64K will take DMA, 9600 baud X.25 should be ok.
- *
- * Z8530:
- * Synchronous mode without DMA is unlikely to pass about 2400 baud.
- */
-
-#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
-
-#include <linux/module.h>
-#include <linux/kernel.h>
-#include <linux/mm.h>
-#include <linux/net.h>
-#include <linux/skbuff.h>
-#include <linux/netdevice.h>
-#include <linux/if_arp.h>
-#include <linux/delay.h>
-#include <linux/hdlc.h>
-#include <linux/ioport.h>
-#include <linux/init.h>
-#include <linux/gfp.h>
-#include <asm/dma.h>
-#include <asm/io.h>
-#define RT_LOCK
-#define RT_UNLOCK
-#include <linux/spinlock.h>
-
-#include "z85230.h"
-
-/**
- * z8530_read_port - Architecture specific interface function
- * @p: port to read
- *
- * Provided port access methods. The Comtrol SV11 requires no delays
- * between accesses and uses PC I/O. Some drivers may need a 5uS delay
- *
- * In the longer term this should become an architecture specific
- * section so that this can become a generic driver interface for all
- * platforms. For now we only handle PC I/O ports with or without the
- * dread 5uS sanity delay.
- *
- * The caller must hold sufficient locks to avoid violating the horrible
- * 5uS delay rule.
- */
-
-static inline int z8530_read_port(unsigned long p)
-{
- u8 r = inb(Z8530_PORT_OF(p));
-
- if (p & Z8530_PORT_SLEEP) /* gcc should figure this out efficiently ! */
- udelay(5);
- return r;
-}
-
-/**
- * z8530_write_port - Architecture specific interface function
- * @p: port to write
- * @d: value to write
- *
- * Write a value to a port with delays if need be. Note that the
- * caller must hold locks to avoid read/writes from other contexts
- * violating the 5uS rule
- *
- * In the longer term this should become an architecture specific
- * section so that this can become a generic driver interface for all
- * platforms. For now we only handle PC I/O ports with or without the
- * dread 5uS sanity delay.
- */
-
-static inline void z8530_write_port(unsigned long p, u8 d)
-{
- outb(d, Z8530_PORT_OF(p));
- if (p & Z8530_PORT_SLEEP)
- udelay(5);
-}
-
-static void z8530_rx_done(struct z8530_channel *c);
-static void z8530_tx_done(struct z8530_channel *c);
-
-/**
- * read_zsreg - Read a register from a Z85230
- * @c: Z8530 channel to read from (2 per chip)
- * @reg: Register to read
- * FIXME: Use a spinlock.
- *
- * Most of the Z8530 registers are indexed off the control registers.
- * A read is done by writing to the control register and reading the
- * register back. The caller must hold the lock
- */
-
-static inline u8 read_zsreg(struct z8530_channel *c, u8 reg)
-{
- if (reg)
- z8530_write_port(c->ctrlio, reg);
- return z8530_read_port(c->ctrlio);
-}
-
-/**
- * read_zsdata - Read the data port of a Z8530 channel
- * @c: The Z8530 channel to read the data port from
- *
- * The data port provides fast access to some things. We still
- * have all the 5uS delays to worry about.
- */
-
-static inline u8 read_zsdata(struct z8530_channel *c)
-{
- u8 r;
-
- r = z8530_read_port(c->dataio);
- return r;
-}
-
-/**
- * write_zsreg - Write to a Z8530 channel register
- * @c: The Z8530 channel
- * @reg: Register number
- * @val: Value to write
- *
- * Write a value to an indexed register. The caller must hold the lock
- * to honour the irritating delay rules. We know about register 0
- * being fast to access.
- *
- * Assumes c->lock is held.
- */
-static inline void write_zsreg(struct z8530_channel *c, u8 reg, u8 val)
-{
- if (reg)
- z8530_write_port(c->ctrlio, reg);
- z8530_write_port(c->ctrlio, val);
-}
-
-/**
- * write_zsctrl - Write to a Z8530 control register
- * @c: The Z8530 channel
- * @val: Value to write
- *
- * Write directly to the control register on the Z8530
- */
-
-static inline void write_zsctrl(struct z8530_channel *c, u8 val)
-{
- z8530_write_port(c->ctrlio, val);
-}
-
-/**
- * write_zsdata - Write to a Z8530 control register
- * @c: The Z8530 channel
- * @val: Value to write
- *
- * Write directly to the data register on the Z8530
- */
-static inline void write_zsdata(struct z8530_channel *c, u8 val)
-{
- z8530_write_port(c->dataio, val);
-}
-
-/* Register loading parameters for a dead port
- */
-
-u8 z8530_dead_port[] = {
- 255
-};
-EXPORT_SYMBOL(z8530_dead_port);
-
-/* Register loading parameters for currently supported circuit types
- */
-
-/* Data clocked by telco end. This is the correct data for the UK
- * "kilostream" service, and most other similar services.
- */
-
-u8 z8530_hdlc_kilostream[] = {
- 4, SYNC_ENAB | SDLC | X1CLK,
- 2, 0, /* No vector */
- 1, 0,
- 3, ENT_HM | RxCRC_ENAB | Rx8,
- 5, TxCRC_ENAB | RTS | TxENAB | Tx8 | DTR,
- 9, 0, /* Disable interrupts */
- 6, 0xFF,
- 7, FLAG,
- 10, ABUNDER | NRZ | CRCPS,/*MARKIDLE ??*/
- 11, TCTRxCP,
- 14, DISDPLL,
- 15, DCDIE | SYNCIE | CTSIE | TxUIE | BRKIE,
- 1, EXT_INT_ENAB | TxINT_ENAB | INT_ALL_Rx,
- 9, NV | MIE | NORESET,
- 255
-};
-EXPORT_SYMBOL(z8530_hdlc_kilostream);
-
-/* As above but for enhanced chips.
- */
-
-u8 z8530_hdlc_kilostream_85230[] = {
- 4, SYNC_ENAB | SDLC | X1CLK,
- 2, 0, /* No vector */
- 1, 0,
- 3, ENT_HM | RxCRC_ENAB | Rx8,
- 5, TxCRC_ENAB | RTS | TxENAB | Tx8 | DTR,
- 9, 0, /* Disable interrupts */
- 6, 0xFF,
- 7, FLAG,
- 10, ABUNDER | NRZ | CRCPS, /* MARKIDLE?? */
- 11, TCTRxCP,
- 14, DISDPLL,
- 15, DCDIE | SYNCIE | CTSIE | TxUIE | BRKIE,
- 1, EXT_INT_ENAB | TxINT_ENAB | INT_ALL_Rx,
- 9, NV | MIE | NORESET,
- 23, 3, /* Extended mode AUTO TX and EOM*/
-
- 255
-};
-EXPORT_SYMBOL(z8530_hdlc_kilostream_85230);
-
-/**
- * z8530_flush_fifo - Flush on chip RX FIFO
- * @c: Channel to flush
- *
- * Flush the receive FIFO. There is no specific option for this, we
- * blindly read bytes and discard them. Reading when there is no data
- * is harmless. The 8530 has a 4 byte FIFO, the 85230 has 8 bytes.
- *
- * All locking is handled for the caller. On return data may still be
- * present if it arrived during the flush.
- */
-
-static void z8530_flush_fifo(struct z8530_channel *c)
-{
- read_zsreg(c, R1);
- read_zsreg(c, R1);
- read_zsreg(c, R1);
- read_zsreg(c, R1);
- if (c->dev->type == Z85230) {
- read_zsreg(c, R1);
- read_zsreg(c, R1);
- read_zsreg(c, R1);
- read_zsreg(c, R1);
- }
-}
-
-/**
- * z8530_rtsdtr - Control the outgoing DTS/RTS line
- * @c: The Z8530 channel to control;
- * @set: 1 to set, 0 to clear
- *
- * Sets or clears DTR/RTS on the requested line. All locking is handled
- * by the caller. For now we assume all boards use the actual RTS/DTR
- * on the chip. Apparently one or two don't. We'll scream about them
- * later.
- */
-
-static void z8530_rtsdtr(struct z8530_channel *c, int set)
-{
- if (set)
- c->regs[5] |= (RTS | DTR);
- else
- c->regs[5] &= ~(RTS | DTR);
- write_zsreg(c, R5, c->regs[5]);
-}
-
-/**
- * z8530_rx - Handle a PIO receive event
- * @c: Z8530 channel to process
- *
- * Receive handler for receiving in PIO mode. This is much like the
- * async one but not quite the same or as complex
- *
- * Note: Its intended that this handler can easily be separated from
- * the main code to run realtime. That'll be needed for some machines
- * (eg to ever clock 64kbits on a sparc ;)).
- *
- * The RT_LOCK macros don't do anything now. Keep the code covered
- * by them as short as possible in all circumstances - clocks cost
- * baud. The interrupt handler is assumed to be atomic w.r.t. to
- * other code - this is true in the RT case too.
- *
- * We only cover the sync cases for this. If you want 2Mbit async
- * do it yourself but consider medical assistance first. This non DMA
- * synchronous mode is portable code. The DMA mode assumes PCI like
- * ISA DMA
- *
- * Called with the device lock held
- */
-
-static void z8530_rx(struct z8530_channel *c)
-{
- u8 ch, stat;
-
- while (1) {
- /* FIFO empty ? */
- if (!(read_zsreg(c, R0) & 1))
- break;
- ch = read_zsdata(c);
- stat = read_zsreg(c, R1);
-
- /* Overrun ?
- */
- if (c->count < c->max) {
- *c->dptr++ = ch;
- c->count++;
- }
-
- if (stat & END_FR) {
- /* Error ?
- */
- if (stat & (Rx_OVR | CRC_ERR)) {
- /* Rewind the buffer and return */
- if (c->skb)
- c->dptr = c->skb->data;
- c->count = 0;
- if (stat & Rx_OVR) {
- pr_warn("%s: overrun\n", c->dev->name);
- c->rx_overrun++;
- }
- if (stat & CRC_ERR) {
- c->rx_crc_err++;
- /* printk("crc error\n"); */
- }
- /* Shove the frame upstream */
- } else {
- /* Drop the lock for RX processing, or
- * there are deadlocks
- */
- z8530_rx_done(c);
- write_zsctrl(c, RES_Rx_CRC);
- }
- }
- }
- /* Clear irq
- */
- write_zsctrl(c, ERR_RES);
- write_zsctrl(c, RES_H_IUS);
-}
-
-/**
- * z8530_tx - Handle a PIO transmit event
- * @c: Z8530 channel to process
- *
- * Z8530 transmit interrupt handler for the PIO mode. The basic
- * idea is to attempt to keep the FIFO fed. We fill as many bytes
- * in as possible, its quite possible that we won't keep up with the
- * data rate otherwise.
- */
-
-static void z8530_tx(struct z8530_channel *c)
-{
- while (c->txcount) {
- /* FIFO full ? */
- if (!(read_zsreg(c, R0) & 4))
- return;
- c->txcount--;
- /* Shovel out the byte
- */
- write_zsreg(c, R8, *c->tx_ptr++);
- write_zsctrl(c, RES_H_IUS);
- /* We are about to underflow */
- if (c->txcount == 0) {
- write_zsctrl(c, RES_EOM_L);
- write_zsreg(c, R10, c->regs[10] & ~ABUNDER);
- }
- }
-
- /* End of frame TX - fire another one
- */
-
- write_zsctrl(c, RES_Tx_P);
-
- z8530_tx_done(c);
- write_zsctrl(c, RES_H_IUS);
-}
-
-/**
- * z8530_status - Handle a PIO status exception
- * @chan: Z8530 channel to process
- *
- * A status event occurred in PIO synchronous mode. There are several
- * reasons the chip will bother us here. A transmit underrun means we
- * failed to feed the chip fast enough and just broke a packet. A DCD
- * change is a line up or down.
- */
-
-static void z8530_status(struct z8530_channel *chan)
-{
- u8 status, altered;
-
- status = read_zsreg(chan, R0);
- altered = chan->status ^ status;
-
- chan->status = status;
-
- if (status & TxEOM) {
-/* printk("%s: Tx underrun.\n", chan->dev->name); */
- chan->netdevice->stats.tx_fifo_errors++;
- write_zsctrl(chan, ERR_RES);
- z8530_tx_done(chan);
- }
-
- if (altered & chan->dcdcheck) {
- if (status & chan->dcdcheck) {
- pr_info("%s: DCD raised\n", chan->dev->name);
- write_zsreg(chan, R3, chan->regs[3] | RxENABLE);
- if (chan->netdevice)
- netif_carrier_on(chan->netdevice);
- } else {
- pr_info("%s: DCD lost\n", chan->dev->name);
- write_zsreg(chan, R3, chan->regs[3] & ~RxENABLE);
- z8530_flush_fifo(chan);
- if (chan->netdevice)
- netif_carrier_off(chan->netdevice);
- }
- }
- write_zsctrl(chan, RES_EXT_INT);
- write_zsctrl(chan, RES_H_IUS);
-}
-
-struct z8530_irqhandler z8530_sync = {
- .rx = z8530_rx,
- .tx = z8530_tx,
- .status = z8530_status,
-};
-EXPORT_SYMBOL(z8530_sync);
-
-/**
- * z8530_dma_rx - Handle a DMA RX event
- * @chan: Channel to handle
- *
- * Non bus mastering DMA interfaces for the Z8x30 devices. This
- * is really pretty PC specific. The DMA mode means that most receive
- * events are handled by the DMA hardware. We get a kick here only if
- * a frame ended.
- */
-
-static void z8530_dma_rx(struct z8530_channel *chan)
-{
- if (chan->rxdma_on) {
- /* Special condition check only */
- u8 status;
-
- read_zsreg(chan, R7);
- read_zsreg(chan, R6);
-
- status = read_zsreg(chan, R1);
-
- if (status & END_FR)
- z8530_rx_done(chan); /* Fire up the next one */
-
- write_zsctrl(chan, ERR_RES);
- write_zsctrl(chan, RES_H_IUS);
- } else {
- /* DMA is off right now, drain the slow way */
- z8530_rx(chan);
- }
-}
-
-/**
- * z8530_dma_tx - Handle a DMA TX event
- * @chan: The Z8530 channel to handle
- *
- * We have received an interrupt while doing DMA transmissions. It
- * shouldn't happen. Scream loudly if it does.
- */
-static void z8530_dma_tx(struct z8530_channel *chan)
-{
- if (!chan->dma_tx) {
- pr_warn("Hey who turned the DMA off?\n");
- z8530_tx(chan);
- return;
- }
- /* This shouldn't occur in DMA mode */
- pr_err("DMA tx - bogus event!\n");
- z8530_tx(chan);
-}
-
-/**
- * z8530_dma_status - Handle a DMA status exception
- * @chan: Z8530 channel to process
- *
- * A status event occurred on the Z8530. We receive these for two reasons
- * when in DMA mode. Firstly if we finished a packet transfer we get one
- * and kick the next packet out. Secondly we may see a DCD change.
- *
- */
-static void z8530_dma_status(struct z8530_channel *chan)
-{
- u8 status, altered;
-
- status = read_zsreg(chan, R0);
- altered = chan->status ^ status;
-
- chan->status = status;
-
- if (chan->dma_tx) {
- if (status & TxEOM) {
- unsigned long flags;
-
- flags = claim_dma_lock();
- disable_dma(chan->txdma);
- clear_dma_ff(chan->txdma);
- chan->txdma_on = 0;
- release_dma_lock(flags);
- z8530_tx_done(chan);
- }
- }
-
- if (altered & chan->dcdcheck) {
- if (status & chan->dcdcheck) {
- pr_info("%s: DCD raised\n", chan->dev->name);
- write_zsreg(chan, R3, chan->regs[3] | RxENABLE);
- if (chan->netdevice)
- netif_carrier_on(chan->netdevice);
- } else {
- pr_info("%s: DCD lost\n", chan->dev->name);
- write_zsreg(chan, R3, chan->regs[3] & ~RxENABLE);
- z8530_flush_fifo(chan);
- if (chan->netdevice)
- netif_carrier_off(chan->netdevice);
- }
- }
-
- write_zsctrl(chan, RES_EXT_INT);
- write_zsctrl(chan, RES_H_IUS);
-}
-
-static struct z8530_irqhandler z8530_dma_sync = {
- .rx = z8530_dma_rx,
- .tx = z8530_dma_tx,
- .status = z8530_dma_status,
-};
-
-static struct z8530_irqhandler z8530_txdma_sync = {
- .rx = z8530_rx,
- .tx = z8530_dma_tx,
- .status = z8530_dma_status,
-};
-
-/**
- * z8530_rx_clear - Handle RX events from a stopped chip
- * @c: Z8530 channel to shut up
- *
- * Receive interrupt vectors for a Z8530 that is in 'parked' mode.
- * For machines with PCI Z85x30 cards, or level triggered interrupts
- * (eg the MacII) we must clear the interrupt cause or die.
- */
-
-static void z8530_rx_clear(struct z8530_channel *c)
-{
- /* Data and status bytes
- */
- u8 stat;
-
- read_zsdata(c);
- stat = read_zsreg(c, R1);
-
- if (stat & END_FR)
- write_zsctrl(c, RES_Rx_CRC);
- /* Clear irq
- */
- write_zsctrl(c, ERR_RES);
- write_zsctrl(c, RES_H_IUS);
-}
-
-/**
- * z8530_tx_clear - Handle TX events from a stopped chip
- * @c: Z8530 channel to shut up
- *
- * Transmit interrupt vectors for a Z8530 that is in 'parked' mode.
- * For machines with PCI Z85x30 cards, or level triggered interrupts
- * (eg the MacII) we must clear the interrupt cause or die.
- */
-
-static void z8530_tx_clear(struct z8530_channel *c)
-{
- write_zsctrl(c, RES_Tx_P);
- write_zsctrl(c, RES_H_IUS);
-}
-
-/**
- * z8530_status_clear - Handle status events from a stopped chip
- * @chan: Z8530 channel to shut up
- *
- * Status interrupt vectors for a Z8530 that is in 'parked' mode.
- * For machines with PCI Z85x30 cards, or level triggered interrupts
- * (eg the MacII) we must clear the interrupt cause or die.
- */
-
-static void z8530_status_clear(struct z8530_channel *chan)
-{
- u8 status = read_zsreg(chan, R0);
-
- if (status & TxEOM)
- write_zsctrl(chan, ERR_RES);
- write_zsctrl(chan, RES_EXT_INT);
- write_zsctrl(chan, RES_H_IUS);
-}
-
-struct z8530_irqhandler z8530_nop = {
- .rx = z8530_rx_clear,
- .tx = z8530_tx_clear,
- .status = z8530_status_clear,
-};
-EXPORT_SYMBOL(z8530_nop);
-
-/**
- * z8530_interrupt - Handle an interrupt from a Z8530
- * @irq: Interrupt number
- * @dev_id: The Z8530 device that is interrupting.
- *
- * A Z85[2]30 device has stuck its hand in the air for attention.
- * We scan both the channels on the chip for events and then call
- * the channel specific call backs for each channel that has events.
- * We have to use callback functions because the two channels can be
- * in different modes.
- *
- * Locking is done for the handlers. Note that locking is done
- * at the chip level (the 5uS delay issue is per chip not per
- * channel). c->lock for both channels points to dev->lock
- */
-
-irqreturn_t z8530_interrupt(int irq, void *dev_id)
-{
- struct z8530_dev *dev = dev_id;
- u8 intr;
- static volatile int locker=0;
- int work = 0;
- struct z8530_irqhandler *irqs;
-
- if (locker) {
- pr_err("IRQ re-enter\n");
- return IRQ_NONE;
- }
- locker = 1;
-
- spin_lock(&dev->lock);
-
- while (++work < 5000) {
- intr = read_zsreg(&dev->chanA, R3);
- if (!(intr &
- (CHARxIP | CHATxIP | CHAEXT | CHBRxIP | CHBTxIP | CHBEXT)))
- break;
-
- /* This holds the IRQ status. On the 8530 you must read it
- * from chan A even though it applies to the whole chip
- */
-
- /* Now walk the chip and see what it is wanting - it may be
- * an IRQ for someone else remember
- */
-
- irqs = dev->chanA.irqs;
-
- if (intr & (CHARxIP | CHATxIP | CHAEXT)) {
- if (intr & CHARxIP)
- irqs->rx(&dev->chanA);
- if (intr & CHATxIP)
- irqs->tx(&dev->chanA);
- if (intr & CHAEXT)
- irqs->status(&dev->chanA);
- }
-
- irqs = dev->chanB.irqs;
-
- if (intr & (CHBRxIP | CHBTxIP | CHBEXT)) {
- if (intr & CHBRxIP)
- irqs->rx(&dev->chanB);
- if (intr & CHBTxIP)
- irqs->tx(&dev->chanB);
- if (intr & CHBEXT)
- irqs->status(&dev->chanB);
- }
- }
- spin_unlock(&dev->lock);
- if (work == 5000)
- pr_err("%s: interrupt jammed - abort(0x%X)!\n",
- dev->name, intr);
- /* Ok all done */
- locker = 0;
- return IRQ_HANDLED;
-}
-EXPORT_SYMBOL(z8530_interrupt);
-
-static const u8 reg_init[16] = {
- 0, 0, 0, 0,
- 0, 0, 0, 0,
- 0, 0, 0, 0,
- 0x55, 0, 0, 0
-};
-
-/**
- * z8530_sync_open - Open a Z8530 channel for PIO
- * @dev: The network interface we are using
- * @c: The Z8530 channel to open in synchronous PIO mode
- *
- * Switch a Z8530 into synchronous mode without DMA assist. We
- * raise the RTS/DTR and commence network operation.
- */
-int z8530_sync_open(struct net_device *dev, struct z8530_channel *c)
-{
- unsigned long flags;
-
- spin_lock_irqsave(c->lock, flags);
-
- c->sync = 1;
- c->mtu = dev->mtu + 64;
- c->count = 0;
- c->skb = NULL;
- c->skb2 = NULL;
- c->irqs = &z8530_sync;
-
- /* This loads the double buffer up */
- z8530_rx_done(c); /* Load the frame ring */
- z8530_rx_done(c); /* Load the backup frame */
- z8530_rtsdtr(c, 1);
- c->dma_tx = 0;
- c->regs[R1] |= TxINT_ENAB;
- write_zsreg(c, R1, c->regs[R1]);
- write_zsreg(c, R3, c->regs[R3] | RxENABLE);
-
- spin_unlock_irqrestore(c->lock, flags);
- return 0;
-}
-EXPORT_SYMBOL(z8530_sync_open);
-
-/**
- * z8530_sync_close - Close a PIO Z8530 channel
- * @dev: Network device to close
- * @c: Z8530 channel to disassociate and move to idle
- *
- * Close down a Z8530 interface and switch its interrupt handlers
- * to discard future events.
- */
-int z8530_sync_close(struct net_device *dev, struct z8530_channel *c)
-{
- u8 chk;
- unsigned long flags;
-
- spin_lock_irqsave(c->lock, flags);
- c->irqs = &z8530_nop;
- c->max = 0;
- c->sync = 0;
-
- chk = read_zsreg(c, R0);
- write_zsreg(c, R3, c->regs[R3]);
- z8530_rtsdtr(c, 0);
-
- spin_unlock_irqrestore(c->lock, flags);
- return 0;
-}
-EXPORT_SYMBOL(z8530_sync_close);
-
-/**
- * z8530_sync_dma_open - Open a Z8530 for DMA I/O
- * @dev: The network device to attach
- * @c: The Z8530 channel to configure in sync DMA mode.
- *
- * Set up a Z85x30 device for synchronous DMA in both directions. Two
- * ISA DMA channels must be available for this to work. We assume ISA
- * DMA driven I/O and PC limits on access.
- */
-int z8530_sync_dma_open(struct net_device *dev, struct z8530_channel *c)
-{
- unsigned long cflags, dflags;
-
- c->sync = 1;
- c->mtu = dev->mtu + 64;
- c->count = 0;
- c->skb = NULL;
- c->skb2 = NULL;
-
- /* Load the DMA interfaces up
- */
- c->rxdma_on = 0;
- c->txdma_on = 0;
-
- /* Allocate the DMA flip buffers. Limit by page size.
- * Everyone runs 1500 mtu or less on wan links so this
- * should be fine.
- */
-
- if (c->mtu > PAGE_SIZE / 2)
- return -EMSGSIZE;
-
- c->rx_buf[0] = (void *)get_zeroed_page(GFP_KERNEL | GFP_DMA);
- if (!c->rx_buf[0])
- return -ENOBUFS;
- c->rx_buf[1] = c->rx_buf[0] + PAGE_SIZE / 2;
-
- c->tx_dma_buf[0] = (void *)get_zeroed_page(GFP_KERNEL | GFP_DMA);
- if (!c->tx_dma_buf[0]) {
- free_page((unsigned long)c->rx_buf[0]);
- c->rx_buf[0] = NULL;
- return -ENOBUFS;
- }
- c->tx_dma_buf[1] = c->tx_dma_buf[0] + PAGE_SIZE / 2;
-
- c->tx_dma_used = 0;
- c->dma_tx = 1;
- c->dma_num = 0;
- c->dma_ready = 1;
-
- /* Enable DMA control mode
- */
-
- spin_lock_irqsave(c->lock, cflags);
-
- /* TX DMA via DIR/REQ
- */
-
- c->regs[R14] |= DTRREQ;
- write_zsreg(c, R14, c->regs[R14]);
-
- c->regs[R1] &= ~TxINT_ENAB;
- write_zsreg(c, R1, c->regs[R1]);
-
- /* RX DMA via W/Req
- */
-
- c->regs[R1] |= WT_FN_RDYFN;
- c->regs[R1] |= WT_RDY_RT;
- c->regs[R1] |= INT_ERR_Rx;
- c->regs[R1] &= ~TxINT_ENAB;
- write_zsreg(c, R1, c->regs[R1]);
- c->regs[R1] |= WT_RDY_ENAB;
- write_zsreg(c, R1, c->regs[R1]);
-
- /* DMA interrupts
- */
-
- /* Set up the DMA configuration
- */
-
- dflags = claim_dma_lock();
-
- disable_dma(c->rxdma);
- clear_dma_ff(c->rxdma);
- set_dma_mode(c->rxdma, DMA_MODE_READ | 0x10);
- set_dma_addr(c->rxdma, virt_to_bus(c->rx_buf[0]));
- set_dma_count(c->rxdma, c->mtu);
- enable_dma(c->rxdma);
-
- disable_dma(c->txdma);
- clear_dma_ff(c->txdma);
- set_dma_mode(c->txdma, DMA_MODE_WRITE);
- disable_dma(c->txdma);
-
- release_dma_lock(dflags);
-
- /* Select the DMA interrupt handlers
- */
-
- c->rxdma_on = 1;
- c->txdma_on = 1;
- c->tx_dma_used = 1;
-
- c->irqs = &z8530_dma_sync;
- z8530_rtsdtr(c, 1);
- write_zsreg(c, R3, c->regs[R3] | RxENABLE);
-
- spin_unlock_irqrestore(c->lock, cflags);
-
- return 0;
-}
-EXPORT_SYMBOL(z8530_sync_dma_open);
-
-/**
- * z8530_sync_dma_close - Close down DMA I/O
- * @dev: Network device to detach
- * @c: Z8530 channel to move into discard mode
- *
- * Shut down a DMA mode synchronous interface. Halt the DMA, and
- * free the buffers.
- */
-int z8530_sync_dma_close(struct net_device *dev, struct z8530_channel *c)
-{
- u8 chk;
- unsigned long flags;
-
- c->irqs = &z8530_nop;
- c->max = 0;
- c->sync = 0;
-
- /* Disable the PC DMA channels
- */
-
- flags = claim_dma_lock();
- disable_dma(c->rxdma);
- clear_dma_ff(c->rxdma);
-
- c->rxdma_on = 0;
-
- disable_dma(c->txdma);
- clear_dma_ff(c->txdma);
- release_dma_lock(flags);
-
- c->txdma_on = 0;
- c->tx_dma_used = 0;
-
- spin_lock_irqsave(c->lock, flags);
-
- /* Disable DMA control mode
- */
-
- c->regs[R1] &= ~WT_RDY_ENAB;
- write_zsreg(c, R1, c->regs[R1]);
- c->regs[R1] &= ~(WT_RDY_RT | WT_FN_RDYFN | INT_ERR_Rx);
- c->regs[R1] |= INT_ALL_Rx;
- write_zsreg(c, R1, c->regs[R1]);
- c->regs[R14] &= ~DTRREQ;
- write_zsreg(c, R14, c->regs[R14]);
-
- if (c->rx_buf[0]) {
- free_page((unsigned long)c->rx_buf[0]);
- c->rx_buf[0] = NULL;
- }
- if (c->tx_dma_buf[0]) {
- free_page((unsigned long)c->tx_dma_buf[0]);
- c->tx_dma_buf[0] = NULL;
- }
- chk = read_zsreg(c, R0);
- write_zsreg(c, R3, c->regs[R3]);
- z8530_rtsdtr(c, 0);
-
- spin_unlock_irqrestore(c->lock, flags);
-
- return 0;
-}
-EXPORT_SYMBOL(z8530_sync_dma_close);
-
-/**
- * z8530_sync_txdma_open - Open a Z8530 for TX driven DMA
- * @dev: The network device to attach
- * @c: The Z8530 channel to configure in sync DMA mode.
- *
- * Set up a Z85x30 device for synchronous DMA transmission. One
- * ISA DMA channel must be available for this to work. The receive
- * side is run in PIO mode, but then it has the bigger FIFO.
- */
-
-int z8530_sync_txdma_open(struct net_device *dev, struct z8530_channel *c)
-{
- unsigned long cflags, dflags;
-
- printk("Opening sync interface for TX-DMA\n");
- c->sync = 1;
- c->mtu = dev->mtu + 64;
- c->count = 0;
- c->skb = NULL;
- c->skb2 = NULL;
-
- /* Allocate the DMA flip buffers. Limit by page size.
- * Everyone runs 1500 mtu or less on wan links so this
- * should be fine.
- */
-
- if (c->mtu > PAGE_SIZE / 2)
- return -EMSGSIZE;
-
- c->tx_dma_buf[0] = (void *)get_zeroed_page(GFP_KERNEL | GFP_DMA);
- if (!c->tx_dma_buf[0])
- return -ENOBUFS;
-
- c->tx_dma_buf[1] = c->tx_dma_buf[0] + PAGE_SIZE / 2;
-
- spin_lock_irqsave(c->lock, cflags);
-
- /* Load the PIO receive ring
- */
-
- z8530_rx_done(c);
- z8530_rx_done(c);
-
- /* Load the DMA interfaces up
- */
-
- c->rxdma_on = 0;
- c->txdma_on = 0;
-
- c->tx_dma_used = 0;
- c->dma_num = 0;
- c->dma_ready = 1;
- c->dma_tx = 1;
-
- /* Enable DMA control mode
- */
-
- /* TX DMA via DIR/REQ
- */
- c->regs[R14] |= DTRREQ;
- write_zsreg(c, R14, c->regs[R14]);
-
- c->regs[R1] &= ~TxINT_ENAB;
- write_zsreg(c, R1, c->regs[R1]);
-
- /* Set up the DMA configuration
- */
-
- dflags = claim_dma_lock();
-
- disable_dma(c->txdma);
- clear_dma_ff(c->txdma);
- set_dma_mode(c->txdma, DMA_MODE_WRITE);
- disable_dma(c->txdma);
-
- release_dma_lock(dflags);
-
- /* Select the DMA interrupt handlers
- */
-
- c->rxdma_on = 0;
- c->txdma_on = 1;
- c->tx_dma_used = 1;
-
- c->irqs = &z8530_txdma_sync;
- z8530_rtsdtr(c, 1);
- write_zsreg(c, R3, c->regs[R3] | RxENABLE);
- spin_unlock_irqrestore(c->lock, cflags);
-
- return 0;
-}
-EXPORT_SYMBOL(z8530_sync_txdma_open);
-
-/**
- * z8530_sync_txdma_close - Close down a TX driven DMA channel
- * @dev: Network device to detach
- * @c: Z8530 channel to move into discard mode
- *
- * Shut down a DMA/PIO split mode synchronous interface. Halt the DMA,
- * and free the buffers.
- */
-
-int z8530_sync_txdma_close(struct net_device *dev, struct z8530_channel *c)
-{
- unsigned long dflags, cflags;
- u8 chk;
-
- spin_lock_irqsave(c->lock, cflags);
-
- c->irqs = &z8530_nop;
- c->max = 0;
- c->sync = 0;
-
- /* Disable the PC DMA channels
- */
-
- dflags = claim_dma_lock();
-
- disable_dma(c->txdma);
- clear_dma_ff(c->txdma);
- c->txdma_on = 0;
- c->tx_dma_used = 0;
-
- release_dma_lock(dflags);
-
- /* Disable DMA control mode
- */
-
- c->regs[R1] &= ~WT_RDY_ENAB;
- write_zsreg(c, R1, c->regs[R1]);
- c->regs[R1] &= ~(WT_RDY_RT | WT_FN_RDYFN | INT_ERR_Rx);
- c->regs[R1] |= INT_ALL_Rx;
- write_zsreg(c, R1, c->regs[R1]);
- c->regs[R14] &= ~DTRREQ;
- write_zsreg(c, R14, c->regs[R14]);
-
- if (c->tx_dma_buf[0]) {
- free_page((unsigned long)c->tx_dma_buf[0]);
- c->tx_dma_buf[0] = NULL;
- }
- chk = read_zsreg(c, R0);
- write_zsreg(c, R3, c->regs[R3]);
- z8530_rtsdtr(c, 0);
-
- spin_unlock_irqrestore(c->lock, cflags);
- return 0;
-}
-EXPORT_SYMBOL(z8530_sync_txdma_close);
-
-/* Name strings for Z8530 chips. SGI claim to have a 130, Zilog deny
- * it exists...
- */
-static const char * const z8530_type_name[] = {
- "Z8530",
- "Z85C30",
- "Z85230"
-};
-
-/**
- * z8530_describe - Uniformly describe a Z8530 port
- * @dev: Z8530 device to describe
- * @mapping: string holding mapping type (eg "I/O" or "Mem")
- * @io: the port value in question
- *
- * Describe a Z8530 in a standard format. We must pass the I/O as
- * the port offset isn't predictable. The main reason for this function
- * is to try and get a common format of report.
- */
-
-void z8530_describe(struct z8530_dev *dev, char *mapping, unsigned long io)
-{
- pr_info("%s: %s found at %s 0x%lX, IRQ %d\n",
- dev->name,
- z8530_type_name[dev->type],
- mapping,
- Z8530_PORT_OF(io),
- dev->irq);
-}
-EXPORT_SYMBOL(z8530_describe);
-
-/* Locked operation part of the z8530 init code
- */
-static inline int do_z8530_init(struct z8530_dev *dev)
-{
- /* NOP the interrupt handlers first - we might get a
- * floating IRQ transition when we reset the chip
- */
- dev->chanA.irqs = &z8530_nop;
- dev->chanB.irqs = &z8530_nop;
- dev->chanA.dcdcheck = DCD;
- dev->chanB.dcdcheck = DCD;
-
- /* Reset the chip */
- write_zsreg(&dev->chanA, R9, 0xC0);
- udelay(200);
- /* Now check its valid */
- write_zsreg(&dev->chanA, R12, 0xAA);
- if (read_zsreg(&dev->chanA, R12) != 0xAA)
- return -ENODEV;
- write_zsreg(&dev->chanA, R12, 0x55);
- if (read_zsreg(&dev->chanA, R12) != 0x55)
- return -ENODEV;
-
- dev->type = Z8530;
-
- /* See the application note.
- */
-
- write_zsreg(&dev->chanA, R15, 0x01);
-
- /* If we can set the low bit of R15 then
- * the chip is enhanced.
- */
-
- if (read_zsreg(&dev->chanA, R15) == 0x01) {
- /* This C30 versus 230 detect is from Klaus Kudielka's dmascc */
- /* Put a char in the fifo */
- write_zsreg(&dev->chanA, R8, 0);
- if (read_zsreg(&dev->chanA, R0) & Tx_BUF_EMP)
- dev->type = Z85230; /* Has a FIFO */
- else
- dev->type = Z85C30; /* Z85C30, 1 byte FIFO */
- }
-
- /* The code assumes R7' and friends are
- * off. Use write_zsext() for these and keep
- * this bit clear.
- */
-
- write_zsreg(&dev->chanA, R15, 0);
-
- /* At this point it looks like the chip is behaving
- */
-
- memcpy(dev->chanA.regs, reg_init, 16);
- memcpy(dev->chanB.regs, reg_init, 16);
-
- return 0;
-}
-
-/**
- * z8530_init - Initialise a Z8530 device
- * @dev: Z8530 device to initialise.
- *
- * Configure up a Z8530/Z85C30 or Z85230 chip. We check the device
- * is present, identify the type and then program it to hopefully
- * keep quite and behave. This matters a lot, a Z8530 in the wrong
- * state will sometimes get into stupid modes generating 10Khz
- * interrupt streams and the like.
- *
- * We set the interrupt handler up to discard any events, in case
- * we get them during reset or setp.
- *
- * Return 0 for success, or a negative value indicating the problem
- * in errno form.
- */
-
-int z8530_init(struct z8530_dev *dev)
-{
- unsigned long flags;
- int ret;
-
- /* Set up the chip level lock */
- spin_lock_init(&dev->lock);
- dev->chanA.lock = &dev->lock;
- dev->chanB.lock = &dev->lock;
-
- spin_lock_irqsave(&dev->lock, flags);
- ret = do_z8530_init(dev);
- spin_unlock_irqrestore(&dev->lock, flags);
-
- return ret;
-}
-EXPORT_SYMBOL(z8530_init);
-
-/**
- * z8530_shutdown - Shutdown a Z8530 device
- * @dev: The Z8530 chip to shutdown
- *
- * We set the interrupt handlers to silence any interrupts. We then
- * reset the chip and wait 100uS to be sure the reset completed. Just
- * in case the caller then tries to do stuff.
- *
- * This is called without the lock held
- */
-int z8530_shutdown(struct z8530_dev *dev)
-{
- unsigned long flags;
- /* Reset the chip */
-
- spin_lock_irqsave(&dev->lock, flags);
- dev->chanA.irqs = &z8530_nop;
- dev->chanB.irqs = &z8530_nop;
- write_zsreg(&dev->chanA, R9, 0xC0);
- /* We must lock the udelay, the chip is offlimits here */
- udelay(100);
- spin_unlock_irqrestore(&dev->lock, flags);
- return 0;
-}
-EXPORT_SYMBOL(z8530_shutdown);
-
-/**
- * z8530_channel_load - Load channel data
- * @c: Z8530 channel to configure
- * @rtable: table of register, value pairs
- * FIXME: ioctl to allow user uploaded tables
- *
- * Load a Z8530 channel up from the system data. We use +16 to
- * indicate the "prime" registers. The value 255 terminates the
- * table.
- */
-
-int z8530_channel_load(struct z8530_channel *c, u8 *rtable)
-{
- unsigned long flags;
-
- spin_lock_irqsave(c->lock, flags);
-
- while (*rtable != 255) {
- int reg = *rtable++;
-
- if (reg > 0x0F)
- write_zsreg(c, R15, c->regs[15] | 1);
- write_zsreg(c, reg & 0x0F, *rtable);
- if (reg > 0x0F)
- write_zsreg(c, R15, c->regs[15] & ~1);
- c->regs[reg] = *rtable++;
- }
- c->rx_function = z8530_null_rx;
- c->skb = NULL;
- c->tx_skb = NULL;
- c->tx_next_skb = NULL;
- c->mtu = 1500;
- c->max = 0;
- c->count = 0;
- c->status = read_zsreg(c, R0);
- c->sync = 1;
- write_zsreg(c, R3, c->regs[R3] | RxENABLE);
-
- spin_unlock_irqrestore(c->lock, flags);
- return 0;
-}
-EXPORT_SYMBOL(z8530_channel_load);
-
-/**
- * z8530_tx_begin - Begin packet transmission
- * @c: The Z8530 channel to kick
- *
- * This is the speed sensitive side of transmission. If we are called
- * and no buffer is being transmitted we commence the next buffer. If
- * nothing is queued we idle the sync.
- *
- * Note: We are handling this code path in the interrupt path, keep it
- * fast or bad things will happen.
- *
- * Called with the lock held.
- */
-
-static void z8530_tx_begin(struct z8530_channel *c)
-{
- unsigned long flags;
-
- if (c->tx_skb)
- return;
-
- c->tx_skb = c->tx_next_skb;
- c->tx_next_skb = NULL;
- c->tx_ptr = c->tx_next_ptr;
-
- if (!c->tx_skb) {
- /* Idle on */
- if (c->dma_tx) {
- flags = claim_dma_lock();
- disable_dma(c->txdma);
- /* Check if we crapped out.
- */
- if (get_dma_residue(c->txdma)) {
- c->netdevice->stats.tx_dropped++;
- c->netdevice->stats.tx_fifo_errors++;
- }
- release_dma_lock(flags);
- }
- c->txcount = 0;
- } else {
- c->txcount = c->tx_skb->len;
-
- if (c->dma_tx) {
- /* FIXME. DMA is broken for the original 8530,
- * on the older parts we need to set a flag and
- * wait for a further TX interrupt to fire this
- * stage off
- */
-
- flags = claim_dma_lock();
- disable_dma(c->txdma);
-
- /* These two are needed by the 8530/85C30
- * and must be issued when idling.
- */
- if (c->dev->type != Z85230) {
- write_zsctrl(c, RES_Tx_CRC);
- write_zsctrl(c, RES_EOM_L);
- }
- write_zsreg(c, R10, c->regs[10] & ~ABUNDER);
- clear_dma_ff(c->txdma);
- set_dma_addr(c->txdma, virt_to_bus(c->tx_ptr));
- set_dma_count(c->txdma, c->txcount);
- enable_dma(c->txdma);
- release_dma_lock(flags);
- write_zsctrl(c, RES_EOM_L);
- write_zsreg(c, R5, c->regs[R5] | TxENAB);
- } else {
- /* ABUNDER off */
- write_zsreg(c, R10, c->regs[10]);
- write_zsctrl(c, RES_Tx_CRC);
-
- while (c->txcount && (read_zsreg(c, R0) & Tx_BUF_EMP)) {
- write_zsreg(c, R8, *c->tx_ptr++);
- c->txcount--;
- }
- }
- }
- /* Since we emptied tx_skb we can ask for more
- */
- netif_wake_queue(c->netdevice);
-}
-
-/**
- * z8530_tx_done - TX complete callback
- * @c: The channel that completed a transmit.
- *
- * This is called when we complete a packet send. We wake the queue,
- * start the next packet going and then free the buffer of the existing
- * packet. This code is fairly timing sensitive.
- *
- * Called with the register lock held.
- */
-
-static void z8530_tx_done(struct z8530_channel *c)
-{
- struct sk_buff *skb;
-
- /* Actually this can happen.*/
- if (!c->tx_skb)
- return;
-
- skb = c->tx_skb;
- c->tx_skb = NULL;
- z8530_tx_begin(c);
- c->netdevice->stats.tx_packets++;
- c->netdevice->stats.tx_bytes += skb->len;
- dev_consume_skb_irq(skb);
-}
-
-/**
- * z8530_null_rx - Discard a packet
- * @c: The channel the packet arrived on
- * @skb: The buffer
- *
- * We point the receive handler at this function when idle. Instead
- * of processing the frames we get to throw them away.
- */
-void z8530_null_rx(struct z8530_channel *c, struct sk_buff *skb)
-{
- dev_kfree_skb_any(skb);
-}
-EXPORT_SYMBOL(z8530_null_rx);
-
-/**
- * z8530_rx_done - Receive completion callback
- * @c: The channel that completed a receive
- *
- * A new packet is complete. Our goal here is to get back into receive
- * mode as fast as possible. On the Z85230 we could change to using
- * ESCC mode, but on the older chips we have no choice. We flip to the
- * new buffer immediately in DMA mode so that the DMA of the next
- * frame can occur while we are copying the previous buffer to an sk_buff
- *
- * Called with the lock held
- */
-static void z8530_rx_done(struct z8530_channel *c)
-{
- struct sk_buff *skb;
- int ct;
-
- /* Is our receive engine in DMA mode
- */
- if (c->rxdma_on) {
- /* Save the ready state and the buffer currently
- * being used as the DMA target
- */
- int ready = c->dma_ready;
- unsigned char *rxb = c->rx_buf[c->dma_num];
- unsigned long flags;
-
- /* Complete this DMA. Necessary to find the length
- */
- flags = claim_dma_lock();
-
- disable_dma(c->rxdma);
- clear_dma_ff(c->rxdma);
- c->rxdma_on = 0;
- ct = c->mtu - get_dma_residue(c->rxdma);
- if (ct < 0)
- ct = 2; /* Shit happens.. */
- c->dma_ready = 0;
-
- /* Normal case: the other slot is free, start the next DMA
- * into it immediately.
- */
-
- if (ready) {
- c->dma_num ^= 1;
- set_dma_mode(c->rxdma, DMA_MODE_READ | 0x10);
- set_dma_addr(c->rxdma, virt_to_bus(c->rx_buf[c->dma_num]));
- set_dma_count(c->rxdma, c->mtu);
- c->rxdma_on = 1;
- enable_dma(c->rxdma);
- /* Stop any frames that we missed the head of
- * from passing
- */
- write_zsreg(c, R0, RES_Rx_CRC);
- } else {
- /* Can't occur as we dont reenable the DMA irq until
- * after the flip is done
- */
- netdev_warn(c->netdevice, "DMA flip overrun!\n");
- }
-
- release_dma_lock(flags);
-
- /* Shove the old buffer into an sk_buff. We can't DMA
- * directly into one on a PC - it might be above the 16Mb
- * boundary. Optimisation - we could check to see if we
- * can avoid the copy. Optimisation 2 - make the memcpy
- * a copychecksum.
- */
-
- skb = dev_alloc_skb(ct);
- if (!skb) {
- c->netdevice->stats.rx_dropped++;
- netdev_warn(c->netdevice, "Memory squeeze\n");
- } else {
- skb_put(skb, ct);
- skb_copy_to_linear_data(skb, rxb, ct);
- c->netdevice->stats.rx_packets++;
- c->netdevice->stats.rx_bytes += ct;
- }
- c->dma_ready = 1;
- } else {
- RT_LOCK;
- skb = c->skb;
-
- /* The game we play for non DMA is similar. We want to
- * get the controller set up for the next packet as fast
- * as possible. We potentially only have one byte + the
- * fifo length for this. Thus we want to flip to the new
- * buffer and then mess around copying and allocating
- * things. For the current case it doesn't matter but
- * if you build a system where the sync irq isn't blocked
- * by the kernel IRQ disable then you need only block the
- * sync IRQ for the RT_LOCK area.
- *
- */
- ct = c->count;
-
- c->skb = c->skb2;
- c->count = 0;
- c->max = c->mtu;
- if (c->skb) {
- c->dptr = c->skb->data;
- c->max = c->mtu;
- } else {
- c->count = 0;
- c->max = 0;
- }
- RT_UNLOCK;
-
- c->skb2 = dev_alloc_skb(c->mtu);
- if (c->skb2)
- skb_put(c->skb2, c->mtu);
-
- c->netdevice->stats.rx_packets++;
- c->netdevice->stats.rx_bytes += ct;
- }
- /* If we received a frame we must now process it.
- */
- if (skb) {
- skb_trim(skb, ct);
- c->rx_function(c, skb);
- } else {
- c->netdevice->stats.rx_dropped++;
- netdev_err(c->netdevice, "Lost a frame\n");
- }
-}
-
-/**
- * spans_boundary - Check a packet can be ISA DMA'd
- * @skb: The buffer to check
- *
- * Returns true if the buffer cross a DMA boundary on a PC. The poor
- * thing can only DMA within a 64K block not across the edges of it.
- */
-
-static inline int spans_boundary(struct sk_buff *skb)
-{
- unsigned long a = (unsigned long)skb->data;
-
- a ^= (a + skb->len);
- if (a & 0x00010000) /* If the 64K bit is different.. */
- return 1;
- return 0;
-}
-
-/**
- * z8530_queue_xmit - Queue a packet
- * @c: The channel to use
- * @skb: The packet to kick down the channel
- *
- * Queue a packet for transmission. Because we have rather
- * hard to hit interrupt latencies for the Z85230 per packet
- * even in DMA mode we do the flip to DMA buffer if needed here
- * not in the IRQ.
- *
- * Called from the network code. The lock is not held at this
- * point.
- */
-netdev_tx_t z8530_queue_xmit(struct z8530_channel *c, struct sk_buff *skb)
-{
- unsigned long flags;
-
- netif_stop_queue(c->netdevice);
- if (c->tx_next_skb)
- return NETDEV_TX_BUSY;
-
- /* PC SPECIFIC - DMA limits */
- /* If we will DMA the transmit and its gone over the ISA bus
- * limit, then copy to the flip buffer
- */
-
- if (c->dma_tx &&
- ((unsigned long)(virt_to_bus(skb->data + skb->len)) >=
- 16 * 1024 * 1024 || spans_boundary(skb))) {
- /* Send the flip buffer, and flip the flippy bit.
- * We don't care which is used when just so long as
- * we never use the same buffer twice in a row. Since
- * only one buffer can be going out at a time the other
- * has to be safe.
- */
- c->tx_next_ptr = c->tx_dma_buf[c->tx_dma_used];
- c->tx_dma_used ^= 1; /* Flip temp buffer */
- skb_copy_from_linear_data(skb, c->tx_next_ptr, skb->len);
- } else {
- c->tx_next_ptr = skb->data;
- }
- RT_LOCK;
- c->tx_next_skb = skb;
- RT_UNLOCK;
-
- spin_lock_irqsave(c->lock, flags);
- z8530_tx_begin(c);
- spin_unlock_irqrestore(c->lock, flags);
-
- return NETDEV_TX_OK;
-}
-EXPORT_SYMBOL(z8530_queue_xmit);
-
-/* Module support
- */
-static const char banner[] __initconst =
- KERN_INFO "Generic Z85C30/Z85230 interface driver v0.02\n";
-
-static int __init z85230_init_driver(void)
-{
- printk(banner);
- return 0;
-}
-module_init(z85230_init_driver);
-
-static void __exit z85230_cleanup_driver(void)
-{
-}
-module_exit(z85230_cleanup_driver);
-
-MODULE_AUTHOR("Red Hat Inc.");
-MODULE_DESCRIPTION("Z85x30 synchronous driver core");
-MODULE_LICENSE("GPL");
diff --git a/drivers/net/wan/z85230.h b/drivers/net/wan/z85230.h
deleted file mode 100644
index 462cb620bc5d..000000000000
--- a/drivers/net/wan/z85230.h
+++ /dev/null
@@ -1,407 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0 */
-/*
- * Description of Z8530 Z85C30 and Z85230 communications chips
- *
- * Copyright (C) 1995 David S. Miller (davem@caip.rutgers.edu)
- * Copyright (C) 1998 Alan Cox <alan@lxorguk.ukuu.org.uk>
- */
-
-#ifndef _Z8530_H
-#define _Z8530_H
-
-#include <linux/tty.h>
-#include <linux/interrupt.h>
-
-/* Conversion routines to/from brg time constants from/to bits
- * per second.
- */
-#define BRG_TO_BPS(brg, freq) ((freq) / 2 / ((brg) + 2))
-#define BPS_TO_BRG(bps, freq) ((((freq) + (bps)) / (2 * (bps))) - 2)
-
-/* The Zilog register set */
-
-#define FLAG 0x7e
-
-/* Write Register 0 */
-#define R0 0 /* Register selects */
-#define R1 1
-#define R2 2
-#define R3 3
-#define R4 4
-#define R5 5
-#define R6 6
-#define R7 7
-#define R8 8
-#define R9 9
-#define R10 10
-#define R11 11
-#define R12 12
-#define R13 13
-#define R14 14
-#define R15 15
-
-#define RPRIME 16 /* Indicate a prime register access on 230 */
-
-#define NULLCODE 0 /* Null Code */
-#define POINT_HIGH 0x8 /* Select upper half of registers */
-#define RES_EXT_INT 0x10 /* Reset Ext. Status Interrupts */
-#define SEND_ABORT 0x18 /* HDLC Abort */
-#define RES_RxINT_FC 0x20 /* Reset RxINT on First Character */
-#define RES_Tx_P 0x28 /* Reset TxINT Pending */
-#define ERR_RES 0x30 /* Error Reset */
-#define RES_H_IUS 0x38 /* Reset highest IUS */
-
-#define RES_Rx_CRC 0x40 /* Reset Rx CRC Checker */
-#define RES_Tx_CRC 0x80 /* Reset Tx CRC Checker */
-#define RES_EOM_L 0xC0 /* Reset EOM latch */
-
-/* Write Register 1 */
-
-#define EXT_INT_ENAB 0x1 /* Ext Int Enable */
-#define TxINT_ENAB 0x2 /* Tx Int Enable */
-#define PAR_SPEC 0x4 /* Parity is special condition */
-
-#define RxINT_DISAB 0 /* Rx Int Disable */
-#define RxINT_FCERR 0x8 /* Rx Int on First Character Only or Error */
-#define INT_ALL_Rx 0x10 /* Int on all Rx Characters or error */
-#define INT_ERR_Rx 0x18 /* Int on error only */
-
-#define WT_RDY_RT 0x20 /* Wait/Ready on R/T */
-#define WT_FN_RDYFN 0x40 /* Wait/FN/Ready FN */
-#define WT_RDY_ENAB 0x80 /* Wait/Ready Enable */
-
-/* Write Register #2 (Interrupt Vector) */
-
-/* Write Register 3 */
-
-#define RxENABLE 0x1 /* Rx Enable */
-#define SYNC_L_INH 0x2 /* Sync Character Load Inhibit */
-#define ADD_SM 0x4 /* Address Search Mode (SDLC) */
-#define RxCRC_ENAB 0x8 /* Rx CRC Enable */
-#define ENT_HM 0x10 /* Enter Hunt Mode */
-#define AUTO_ENAB 0x20 /* Auto Enables */
-#define Rx5 0x0 /* Rx 5 Bits/Character */
-#define Rx7 0x40 /* Rx 7 Bits/Character */
-#define Rx6 0x80 /* Rx 6 Bits/Character */
-#define Rx8 0xc0 /* Rx 8 Bits/Character */
-
-/* Write Register 4 */
-
-#define PAR_ENA 0x1 /* Parity Enable */
-#define PAR_EVEN 0x2 /* Parity Even/Odd* */
-
-#define SYNC_ENAB 0 /* Sync Modes Enable */
-#define SB1 0x4 /* 1 stop bit/char */
-#define SB15 0x8 /* 1.5 stop bits/char */
-#define SB2 0xc /* 2 stop bits/char */
-
-#define MONSYNC 0 /* 8 Bit Sync character */
-#define BISYNC 0x10 /* 16 bit sync character */
-#define SDLC 0x20 /* SDLC Mode (01111110 Sync Flag) */
-#define EXTSYNC 0x30 /* External Sync Mode */
-
-#define X1CLK 0x0 /* x1 clock mode */
-#define X16CLK 0x40 /* x16 clock mode */
-#define X32CLK 0x80 /* x32 clock mode */
-#define X64CLK 0xC0 /* x64 clock mode */
-
-/* Write Register 5 */
-
-#define TxCRC_ENAB 0x1 /* Tx CRC Enable */
-#define RTS 0x2 /* RTS */
-#define SDLC_CRC 0x4 /* SDLC/CRC-16 */
-#define TxENAB 0x8 /* Tx Enable */
-#define SND_BRK 0x10 /* Send Break */
-#define Tx5 0x0 /* Tx 5 bits (or less)/character */
-#define Tx7 0x20 /* Tx 7 bits/character */
-#define Tx6 0x40 /* Tx 6 bits/character */
-#define Tx8 0x60 /* Tx 8 bits/character */
-#define DTR 0x80 /* DTR */
-
-/* Write Register 6 (Sync bits 0-7/SDLC Address Field) */
-
-/* Write Register 7 (Sync bits 8-15/SDLC 01111110) */
-
-/* Write Register 8 (transmit buffer) */
-
-/* Write Register 9 (Master interrupt control) */
-#define VIS 1 /* Vector Includes Status */
-#define NV 2 /* No Vector */
-#define DLC 4 /* Disable Lower Chain */
-#define MIE 8 /* Master Interrupt Enable */
-#define STATHI 0x10 /* Status high */
-#define NORESET 0 /* No reset on write to R9 */
-#define CHRB 0x40 /* Reset channel B */
-#define CHRA 0x80 /* Reset channel A */
-#define FHWRES 0xc0 /* Force hardware reset */
-
-/* Write Register 10 (misc control bits) */
-#define BIT6 1 /* 6 bit/8bit sync */
-#define LOOPMODE 2 /* SDLC Loop mode */
-#define ABUNDER 4 /* Abort/flag on SDLC xmit underrun */
-#define MARKIDLE 8 /* Mark/flag on idle */
-#define GAOP 0x10 /* Go active on poll */
-#define NRZ 0 /* NRZ mode */
-#define NRZI 0x20 /* NRZI mode */
-#define FM1 0x40 /* FM1 (transition = 1) */
-#define FM0 0x60 /* FM0 (transition = 0) */
-#define CRCPS 0x80 /* CRC Preset I/O */
-
-/* Write Register 11 (Clock Mode control) */
-#define TRxCXT 0 /* TRxC = Xtal output */
-#define TRxCTC 1 /* TRxC = Transmit clock */
-#define TRxCBR 2 /* TRxC = BR Generator Output */
-#define TRxCDP 3 /* TRxC = DPLL output */
-#define TRxCOI 4 /* TRxC O/I */
-#define TCRTxCP 0 /* Transmit clock = RTxC pin */
-#define TCTRxCP 8 /* Transmit clock = TRxC pin */
-#define TCBR 0x10 /* Transmit clock = BR Generator output */
-#define TCDPLL 0x18 /* Transmit clock = DPLL output */
-#define RCRTxCP 0 /* Receive clock = RTxC pin */
-#define RCTRxCP 0x20 /* Receive clock = TRxC pin */
-#define RCBR 0x40 /* Receive clock = BR Generator output */
-#define RCDPLL 0x60 /* Receive clock = DPLL output */
-#define RTxCX 0x80 /* RTxC Xtal/No Xtal */
-
-/* Write Register 12 (lower byte of baud rate generator time constant) */
-
-/* Write Register 13 (upper byte of baud rate generator time constant) */
-
-/* Write Register 14 (Misc control bits) */
-#define BRENABL 1 /* Baud rate generator enable */
-#define BRSRC 2 /* Baud rate generator source */
-#define DTRREQ 4 /* DTR/Request function */
-#define AUTOECHO 8 /* Auto Echo */
-#define LOOPBAK 0x10 /* Local loopback */
-#define SEARCH 0x20 /* Enter search mode */
-#define RMC 0x40 /* Reset missing clock */
-#define DISDPLL 0x60 /* Disable DPLL */
-#define SSBR 0x80 /* Set DPLL source = BR generator */
-#define SSRTxC 0xa0 /* Set DPLL source = RTxC */
-#define SFMM 0xc0 /* Set FM mode */
-#define SNRZI 0xe0 /* Set NRZI mode */
-
-/* Write Register 15 (external/status interrupt control) */
-#define PRIME 1 /* R5' etc register access (Z85C30/230 only) */
-#define ZCIE 2 /* Zero count IE */
-#define FIFOE 4 /* Z85230 only */
-#define DCDIE 8 /* DCD IE */
-#define SYNCIE 0x10 /* Sync/hunt IE */
-#define CTSIE 0x20 /* CTS IE */
-#define TxUIE 0x40 /* Tx Underrun/EOM IE */
-#define BRKIE 0x80 /* Break/Abort IE */
-
-
-/* Read Register 0 */
-#define Rx_CH_AV 0x1 /* Rx Character Available */
-#define ZCOUNT 0x2 /* Zero count */
-#define Tx_BUF_EMP 0x4 /* Tx Buffer empty */
-#define DCD 0x8 /* DCD */
-#define SYNC_HUNT 0x10 /* Sync/hunt */
-#define CTS 0x20 /* CTS */
-#define TxEOM 0x40 /* Tx underrun */
-#define BRK_ABRT 0x80 /* Break/Abort */
-
-/* Read Register 1 */
-#define ALL_SNT 0x1 /* All sent */
-/* Residue Data for 8 Rx bits/char programmed */
-#define RES3 0x8 /* 0/3 */
-#define RES4 0x4 /* 0/4 */
-#define RES5 0xc /* 0/5 */
-#define RES6 0x2 /* 0/6 */
-#define RES7 0xa /* 0/7 */
-#define RES8 0x6 /* 0/8 */
-#define RES18 0xe /* 1/8 */
-#define RES28 0x0 /* 2/8 */
-/* Special Rx Condition Interrupts */
-#define PAR_ERR 0x10 /* Parity error */
-#define Rx_OVR 0x20 /* Rx Overrun Error */
-#define CRC_ERR 0x40 /* CRC/Framing Error */
-#define END_FR 0x80 /* End of Frame (SDLC) */
-
-/* Read Register 2 (channel b only) - Interrupt vector */
-
-/* Read Register 3 (interrupt pending register) ch a only */
-#define CHBEXT 0x1 /* Channel B Ext/Stat IP */
-#define CHBTxIP 0x2 /* Channel B Tx IP */
-#define CHBRxIP 0x4 /* Channel B Rx IP */
-#define CHAEXT 0x8 /* Channel A Ext/Stat IP */
-#define CHATxIP 0x10 /* Channel A Tx IP */
-#define CHARxIP 0x20 /* Channel A Rx IP */
-
-/* Read Register 8 (receive data register) */
-
-/* Read Register 10 (misc status bits) */
-#define ONLOOP 2 /* On loop */
-#define LOOPSEND 0x10 /* Loop sending */
-#define CLK2MIS 0x40 /* Two clocks missing */
-#define CLK1MIS 0x80 /* One clock missing */
-
-/* Read Register 12 (lower byte of baud rate generator constant) */
-
-/* Read Register 13 (upper byte of baud rate generator constant) */
-
-/* Read Register 15 (value of WR 15) */
-
-
-/*
- * Interrupt handling functions for this SCC
- */
-
-struct z8530_channel;
-
-struct z8530_irqhandler
-{
- void (*rx)(struct z8530_channel *);
- void (*tx)(struct z8530_channel *);
- void (*status)(struct z8530_channel *);
-};
-
-/*
- * A channel of the Z8530
- */
-
-struct z8530_channel
-{
- struct z8530_irqhandler *irqs; /* IRQ handlers */
- /*
- * Synchronous
- */
- u16 count; /* Buyes received */
- u16 max; /* Most we can receive this frame */
- u16 mtu; /* MTU of the device */
- u8 *dptr; /* Pointer into rx buffer */
- struct sk_buff *skb; /* Buffer dptr points into */
- struct sk_buff *skb2; /* Pending buffer */
- u8 status; /* Current DCD */
- u8 dcdcheck; /* which bit to check for line */
- u8 sync; /* Set if in sync mode */
-
- u8 regs[32]; /* Register map for the chip */
- u8 pendregs[32]; /* Pending register values */
-
- struct sk_buff *tx_skb; /* Buffer being transmitted */
- struct sk_buff *tx_next_skb; /* Next transmit buffer */
- u8 *tx_ptr; /* Byte pointer into the buffer */
- u8 *tx_next_ptr; /* Next pointer to use */
- u8 *tx_dma_buf[2]; /* TX flip buffers for DMA */
- u8 tx_dma_used; /* Flip buffer usage toggler */
- u16 txcount; /* Count of bytes to transmit */
-
- void (*rx_function)(struct z8530_channel *, struct sk_buff *);
-
- /*
- * Sync DMA
- */
-
- u8 rxdma; /* DMA channels */
- u8 txdma;
- u8 rxdma_on; /* DMA active if flag set */
- u8 txdma_on;
- u8 dma_num; /* Buffer we are DMAing into */
- u8 dma_ready; /* Is the other buffer free */
- u8 dma_tx; /* TX is to use DMA */
- u8 *rx_buf[2]; /* The flip buffers */
-
- /*
- * System
- */
-
- struct z8530_dev *dev; /* Z85230 chip instance we are from */
- unsigned long ctrlio; /* I/O ports */
- unsigned long dataio;
-
- /*
- * For PC we encode this way.
- */
-#define Z8530_PORT_SLEEP 0x80000000
-#define Z8530_PORT_OF(x) ((x)&0xFFFF)
-
- u32 rx_overrun; /* Overruns - not done yet */
- u32 rx_crc_err;
-
- /*
- * Bound device pointers
- */
-
- void *private; /* For our owner */
- struct net_device *netdevice; /* Network layer device */
-
- spinlock_t *lock; /* Device lock */
-};
-
-/*
- * Each Z853x0 device.
- */
-
-struct z8530_dev
-{
- char *name; /* Device instance name */
- struct z8530_channel chanA; /* SCC channel A */
- struct z8530_channel chanB; /* SCC channel B */
- int type;
-#define Z8530 0 /* NMOS dinosaur */
-#define Z85C30 1 /* CMOS - better */
-#define Z85230 2 /* CMOS with real FIFO */
- int irq; /* Interrupt for the device */
- int active; /* Soft interrupt enable - the Mac doesn't
- always have a hard disable on its 8530s... */
- spinlock_t lock;
-};
-
-
-/*
- * Functions
- */
-
-extern u8 z8530_dead_port[];
-extern u8 z8530_hdlc_kilostream_85230[];
-extern u8 z8530_hdlc_kilostream[];
-irqreturn_t z8530_interrupt(int, void *);
-void z8530_describe(struct z8530_dev *, char *mapping, unsigned long io);
-int z8530_init(struct z8530_dev *);
-int z8530_shutdown(struct z8530_dev *);
-int z8530_sync_open(struct net_device *, struct z8530_channel *);
-int z8530_sync_close(struct net_device *, struct z8530_channel *);
-int z8530_sync_dma_open(struct net_device *, struct z8530_channel *);
-int z8530_sync_dma_close(struct net_device *, struct z8530_channel *);
-int z8530_sync_txdma_open(struct net_device *, struct z8530_channel *);
-int z8530_sync_txdma_close(struct net_device *, struct z8530_channel *);
-int z8530_channel_load(struct z8530_channel *, u8 *);
-netdev_tx_t z8530_queue_xmit(struct z8530_channel *c, struct sk_buff *skb);
-void z8530_null_rx(struct z8530_channel *c, struct sk_buff *skb);
-
-
-/*
- * Standard interrupt vector sets
- */
-
-extern struct z8530_irqhandler z8530_sync, z8530_async, z8530_nop;
-
-/*
- * Asynchronous Interfacing
- */
-
-/*
- * The size of the serial xmit buffer is 1 page, or 4096 bytes
- */
-
-#define SERIAL_XMIT_SIZE 4096
-#define WAKEUP_CHARS 256
-
-/*
- * Events are used to schedule things to happen at timer-interrupt
- * time, instead of at rs interrupt time.
- */
-#define RS_EVENT_WRITE_WAKEUP 0
-
-/* Internal flags used only by kernel/chr_drv/serial.c */
-#define ZILOG_INITIALIZED 0x80000000 /* Serial port was initialized */
-#define ZILOG_CALLOUT_ACTIVE 0x40000000 /* Call out device is active */
-#define ZILOG_NORMAL_ACTIVE 0x20000000 /* Normal device is active */
-#define ZILOG_BOOT_AUTOCONF 0x10000000 /* Autoconfigure port on bootup */
-#define ZILOG_CLOSING 0x08000000 /* Serial port is closing */
-#define ZILOG_CTS_FLOW 0x04000000 /* Do CTS flow control */
-#define ZILOG_CHECK_CD 0x02000000 /* i.e., CLOCAL */
-
-#endif /* !(_Z8530_H) */
--
2.34.1
next prev parent reply other threads:[~2022-04-26 17:55 UTC|newest]
Thread overview: 17+ messages / expand[flat|nested] mbox.gz Atom feed top
2022-04-26 17:54 [PATCH net-next 0/6] net: remove non-Ethernet drivers using virt_to_bus() Jakub Kicinski
2022-04-26 17:54 ` [PATCH net-next 1/6] net: atm: remove support for Fujitsu FireStream ATM devices Jakub Kicinski
2022-04-26 17:54 ` [PATCH net-next 2/6] net: atm: remove support for Madge Horizon " Jakub Kicinski
2022-04-26 17:54 ` [PATCH net-next 3/6] net: atm: remove support for ZeitNet ZN122x " Jakub Kicinski
2022-08-10 7:36 ` Jiri Slaby
2022-08-10 9:11 ` Arnd Bergmann
2022-08-10 16:42 ` Jakub Kicinski
2022-08-11 5:19 ` Jiri Slaby
2022-08-11 9:18 ` Arnd Bergmann
2022-04-26 17:54 ` [PATCH net-next 4/6] net: wan: remove support for COSA and SRP synchronous serial boards Jakub Kicinski
2022-04-26 17:54 ` Jakub Kicinski [this message]
2022-04-26 17:54 ` [PATCH net-next 6/6] net: hamradio: remove support for DMA SCC devices Jakub Kicinski
2022-04-26 18:55 ` Thomas Osterried
2022-04-26 19:39 ` Jakub Kicinski
2022-04-27 13:27 ` Arnd Bergmann
2022-05-02 1:01 ` Thomas Osterried
2022-04-27 11:30 ` [PATCH net-next 0/6] net: remove non-Ethernet drivers using virt_to_bus() patchwork-bot+netdevbpf
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20220426175436.417283-6-kuba@kernel.org \
--to=kuba@kernel.org \
--cc=alan@linux.intel.com \
--cc=arnd@arndb.de \
--cc=corbet@lwn.net \
--cc=dario.binacchi@amarulasolutions.com \
--cc=davem@davemloft.net \
--cc=huangguangbin2@huawei.com \
--cc=juerg.haefliger@canonical.com \
--cc=kilobyte@angband.pl \
--cc=linus.walleij@linaro.org \
--cc=linux-doc@vger.kernel.org \
--cc=lipeng321@huawei.com \
--cc=m.chetan.kumar@intel.com \
--cc=mkl@pengutronix.de \
--cc=netdev@vger.kernel.org \
--cc=pabeni@redhat.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.