* [PATCH v2 0/2] mfd: flexcom: add a driver for Flexcom
@ 2015-06-18 13:05 ` Cyrille Pitchen
0 siblings, 0 replies; 18+ messages in thread
From: Cyrille Pitchen @ 2015-06-18 13:05 UTC (permalink / raw)
To: nicolas.ferre, boris.brezillon, alexandre.belloni, sameo,
lee.jones
Cc: linux-arm-kernel, linux-kernel, robh+dt, pawel.moll, mark.rutland,
ijc+devicetree, galak, devicetree, Cyrille Pitchen
ChangeLog
v2:
- enhance the documentation of DT bindings and change the way the "ranges"
property is used.
- replace __raw_readl() and __raw_writel() by readl() and writel().
- change the module license to "GPL" for v2 or later
- print the selected flexcom mode after the hardware version
v1:
This series of patches a support to the Atmel Flexcom, a wrapper which
integrates an USART, a SPI controller and a TWI controller. Only one
peripheral can be used at a time. The active function is selected though
the Flexcom Mode Register.
Cyrille Pitchen (2):
mfd: devicetree: add bindings for Atmel Flexcom
mfd: flexcom: add a driver for Atmel Flexible Serial Communication
Unit
.../devicetree/bindings/mfd/atmel-flexcom.txt | 58 +++++++++++++
drivers/mfd/Kconfig | 11 +++
drivers/mfd/Makefile | 1 +
drivers/mfd/atmel-flexcom.c | 97 ++++++++++++++++++++++
4 files changed, 167 insertions(+)
create mode 100644 Documentation/devicetree/bindings/mfd/atmel-flexcom.txt
create mode 100644 drivers/mfd/atmel-flexcom.c
--
1.8.2.2
^ permalink raw reply [flat|nested] 18+ messages in thread
* [PATCH v2 0/2] mfd: flexcom: add a driver for Flexcom
@ 2015-06-18 13:05 ` Cyrille Pitchen
0 siblings, 0 replies; 18+ messages in thread
From: Cyrille Pitchen @ 2015-06-18 13:05 UTC (permalink / raw)
To: nicolas.ferre-AIFe0yeh4nAAvxtiuMwx3w,
boris.brezillon-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8,
alexandre.belloni-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8,
sameo-VuQAYsv1563Yd54FQh9/CA, lee.jones-QSEj5FYQhm4dnm+yROfE0A
Cc: linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
robh+dt-DgEjT+Ai2ygdnm+yROfE0A, pawel.moll-5wv7dgnIgG8,
mark.rutland-5wv7dgnIgG8, ijc+devicetree-KcIKpvwj1kUDXYZnReoRVg,
galak-sgV2jX0FEOL9JmXXK+q4OQ, devicetree-u79uwXL29TY76Z2rM5mHXA,
Cyrille Pitchen
ChangeLog
v2:
- enhance the documentation of DT bindings and change the way the "ranges"
property is used.
- replace __raw_readl() and __raw_writel() by readl() and writel().
- change the module license to "GPL" for v2 or later
- print the selected flexcom mode after the hardware version
v1:
This series of patches a support to the Atmel Flexcom, a wrapper which
integrates an USART, a SPI controller and a TWI controller. Only one
peripheral can be used at a time. The active function is selected though
the Flexcom Mode Register.
Cyrille Pitchen (2):
mfd: devicetree: add bindings for Atmel Flexcom
mfd: flexcom: add a driver for Atmel Flexible Serial Communication
Unit
.../devicetree/bindings/mfd/atmel-flexcom.txt | 58 +++++++++++++
drivers/mfd/Kconfig | 11 +++
drivers/mfd/Makefile | 1 +
drivers/mfd/atmel-flexcom.c | 97 ++++++++++++++++++++++
4 files changed, 167 insertions(+)
create mode 100644 Documentation/devicetree/bindings/mfd/atmel-flexcom.txt
create mode 100644 drivers/mfd/atmel-flexcom.c
--
1.8.2.2
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 18+ messages in thread
* [PATCH v2 0/2] mfd: flexcom: add a driver for Flexcom
@ 2015-06-18 13:05 ` Cyrille Pitchen
0 siblings, 0 replies; 18+ messages in thread
From: Cyrille Pitchen @ 2015-06-18 13:05 UTC (permalink / raw)
To: linux-arm-kernel
ChangeLog
v2:
- enhance the documentation of DT bindings and change the way the "ranges"
property is used.
- replace __raw_readl() and __raw_writel() by readl() and writel().
- change the module license to "GPL" for v2 or later
- print the selected flexcom mode after the hardware version
v1:
This series of patches a support to the Atmel Flexcom, a wrapper which
integrates an USART, a SPI controller and a TWI controller. Only one
peripheral can be used at a time. The active function is selected though
the Flexcom Mode Register.
Cyrille Pitchen (2):
mfd: devicetree: add bindings for Atmel Flexcom
mfd: flexcom: add a driver for Atmel Flexible Serial Communication
Unit
.../devicetree/bindings/mfd/atmel-flexcom.txt | 58 +++++++++++++
drivers/mfd/Kconfig | 11 +++
drivers/mfd/Makefile | 1 +
drivers/mfd/atmel-flexcom.c | 97 ++++++++++++++++++++++
4 files changed, 167 insertions(+)
create mode 100644 Documentation/devicetree/bindings/mfd/atmel-flexcom.txt
create mode 100644 drivers/mfd/atmel-flexcom.c
--
1.8.2.2
^ permalink raw reply [flat|nested] 18+ messages in thread
* [PATCH v2 1/2] mfd: devicetree: add bindings for Atmel Flexcom
2015-06-18 13:05 ` Cyrille Pitchen
(?)
@ 2015-06-18 13:05 ` Cyrille Pitchen
-1 siblings, 0 replies; 18+ messages in thread
From: Cyrille Pitchen @ 2015-06-18 13:05 UTC (permalink / raw)
To: nicolas.ferre, boris.brezillon, alexandre.belloni, sameo,
lee.jones
Cc: linux-arm-kernel, linux-kernel, robh+dt, pawel.moll, mark.rutland,
ijc+devicetree, galak, devicetree, Cyrille Pitchen
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
---
.../devicetree/bindings/mfd/atmel-flexcom.txt | 58 ++++++++++++++++++++++
1 file changed, 58 insertions(+)
create mode 100644 Documentation/devicetree/bindings/mfd/atmel-flexcom.txt
diff --git a/Documentation/devicetree/bindings/mfd/atmel-flexcom.txt b/Documentation/devicetree/bindings/mfd/atmel-flexcom.txt
new file mode 100644
index 0000000..38f0e43
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/atmel-flexcom.txt
@@ -0,0 +1,58 @@
+* Device tree bindings for Atmel Flexcom (Flexible Serial Communication Unit)
+
+The Atmel Flexcom is just a wrapper which embeds a SPI controller, an I2C
+controller and an USART. Only one function can be used at a time and is chosen
+at boot time according to the device tree.
+
+Required properties:
+- compatible: "atmel,sama5d2-flexcom"
+- reg: shall be the offset/length value for Flexcom dedicated I/O registers
+ (without USART, TWI or SPI registers).
+- clocks: shall be the Flexcom peripheral clock from PMC.
+- #address-cells: should be <1>
+- #size-cells: should be <1>
+- ranges: one range for the full I/O register region (including USART, TWI and
+ SPI registers)
+- atmel,flexcom-mode: shall be a string among { "spi", "usart", "i2c", "twi" }.
+ "i2c" and "twi" are synonymous.
+
+Required child:
+a child device of type matching the "atmel,flexcom-mode" property.
+The reg property of this child should be:
+- <0x200 0x200> for USART
+- <0x400 0x200> for SPI
+- <0x600 0x200> for I2C
+The phandle provided by the clocks property of the child is the same as one for
+the Flexcom parent.
+Other properties remain unchanged. See documentation of the respective device.
+
+Example:
+
+flx0: flexcom@f8034000 {
+ compatible = "atmel,sama5d2-flexcom";
+ reg = <0xf8034000 0x200>;
+ clocks = <&flx0_clk>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0x0 0xf8034000 0x800>;
+ atmel,flexcom-mode = "spi";
+
+ spi@f8034400 {
+ compatible = "atmel,at91rm9200-spi";
+ reg = <0x400 0x200>;
+ interrupts = <19 IRQ_TYPE_LEVEL_HIGH 7>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flx0_ioset1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&flx0_clk>;
+ clock-names = "spi_clk";
+ atmel,fifo-size = <32>;
+
+ mtd_dataflash@0 {
+ compatible = "atmel,at25f512b";
+ reg = <0>;
+ spi-max-frequency = <20000000>;
+ };
+ };
+};
--
1.8.2.2
^ permalink raw reply related [flat|nested] 18+ messages in thread
* [PATCH v2 1/2] mfd: devicetree: add bindings for Atmel Flexcom
@ 2015-06-18 13:05 ` Cyrille Pitchen
0 siblings, 0 replies; 18+ messages in thread
From: Cyrille Pitchen @ 2015-06-18 13:05 UTC (permalink / raw)
To: nicolas.ferre, boris.brezillon, alexandre.belloni, sameo,
lee.jones
Cc: linux-arm-kernel, linux-kernel, robh+dt, pawel.moll, mark.rutland,
ijc+devicetree, galak, devicetree, Cyrille Pitchen
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
---
.../devicetree/bindings/mfd/atmel-flexcom.txt | 58 ++++++++++++++++++++++
1 file changed, 58 insertions(+)
create mode 100644 Documentation/devicetree/bindings/mfd/atmel-flexcom.txt
diff --git a/Documentation/devicetree/bindings/mfd/atmel-flexcom.txt b/Documentation/devicetree/bindings/mfd/atmel-flexcom.txt
new file mode 100644
index 0000000..38f0e43
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/atmel-flexcom.txt
@@ -0,0 +1,58 @@
+* Device tree bindings for Atmel Flexcom (Flexible Serial Communication Unit)
+
+The Atmel Flexcom is just a wrapper which embeds a SPI controller, an I2C
+controller and an USART. Only one function can be used at a time and is chosen
+at boot time according to the device tree.
+
+Required properties:
+- compatible: "atmel,sama5d2-flexcom"
+- reg: shall be the offset/length value for Flexcom dedicated I/O registers
+ (without USART, TWI or SPI registers).
+- clocks: shall be the Flexcom peripheral clock from PMC.
+- #address-cells: should be <1>
+- #size-cells: should be <1>
+- ranges: one range for the full I/O register region (including USART, TWI and
+ SPI registers)
+- atmel,flexcom-mode: shall be a string among { "spi", "usart", "i2c", "twi" }.
+ "i2c" and "twi" are synonymous.
+
+Required child:
+a child device of type matching the "atmel,flexcom-mode" property.
+The reg property of this child should be:
+- <0x200 0x200> for USART
+- <0x400 0x200> for SPI
+- <0x600 0x200> for I2C
+The phandle provided by the clocks property of the child is the same as one for
+the Flexcom parent.
+Other properties remain unchanged. See documentation of the respective device.
+
+Example:
+
+flx0: flexcom@f8034000 {
+ compatible = "atmel,sama5d2-flexcom";
+ reg = <0xf8034000 0x200>;
+ clocks = <&flx0_clk>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0x0 0xf8034000 0x800>;
+ atmel,flexcom-mode = "spi";
+
+ spi@f8034400 {
+ compatible = "atmel,at91rm9200-spi";
+ reg = <0x400 0x200>;
+ interrupts = <19 IRQ_TYPE_LEVEL_HIGH 7>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flx0_ioset1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&flx0_clk>;
+ clock-names = "spi_clk";
+ atmel,fifo-size = <32>;
+
+ mtd_dataflash@0 {
+ compatible = "atmel,at25f512b";
+ reg = <0>;
+ spi-max-frequency = <20000000>;
+ };
+ };
+};
--
1.8.2.2
^ permalink raw reply related [flat|nested] 18+ messages in thread
* [PATCH v2 1/2] mfd: devicetree: add bindings for Atmel Flexcom
@ 2015-06-18 13:05 ` Cyrille Pitchen
0 siblings, 0 replies; 18+ messages in thread
From: Cyrille Pitchen @ 2015-06-18 13:05 UTC (permalink / raw)
To: linux-arm-kernel
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
---
.../devicetree/bindings/mfd/atmel-flexcom.txt | 58 ++++++++++++++++++++++
1 file changed, 58 insertions(+)
create mode 100644 Documentation/devicetree/bindings/mfd/atmel-flexcom.txt
diff --git a/Documentation/devicetree/bindings/mfd/atmel-flexcom.txt b/Documentation/devicetree/bindings/mfd/atmel-flexcom.txt
new file mode 100644
index 0000000..38f0e43
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/atmel-flexcom.txt
@@ -0,0 +1,58 @@
+* Device tree bindings for Atmel Flexcom (Flexible Serial Communication Unit)
+
+The Atmel Flexcom is just a wrapper which embeds a SPI controller, an I2C
+controller and an USART. Only one function can be used at a time and is chosen
+at boot time according to the device tree.
+
+Required properties:
+- compatible: "atmel,sama5d2-flexcom"
+- reg: shall be the offset/length value for Flexcom dedicated I/O registers
+ (without USART, TWI or SPI registers).
+- clocks: shall be the Flexcom peripheral clock from PMC.
+- #address-cells: should be <1>
+- #size-cells: should be <1>
+- ranges: one range for the full I/O register region (including USART, TWI and
+ SPI registers)
+- atmel,flexcom-mode: shall be a string among { "spi", "usart", "i2c", "twi" }.
+ "i2c" and "twi" are synonymous.
+
+Required child:
+a child device of type matching the "atmel,flexcom-mode" property.
+The reg property of this child should be:
+- <0x200 0x200> for USART
+- <0x400 0x200> for SPI
+- <0x600 0x200> for I2C
+The phandle provided by the clocks property of the child is the same as one for
+the Flexcom parent.
+Other properties remain unchanged. See documentation of the respective device.
+
+Example:
+
+flx0: flexcom at f8034000 {
+ compatible = "atmel,sama5d2-flexcom";
+ reg = <0xf8034000 0x200>;
+ clocks = <&flx0_clk>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0x0 0xf8034000 0x800>;
+ atmel,flexcom-mode = "spi";
+
+ spi at f8034400 {
+ compatible = "atmel,at91rm9200-spi";
+ reg = <0x400 0x200>;
+ interrupts = <19 IRQ_TYPE_LEVEL_HIGH 7>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flx0_ioset1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&flx0_clk>;
+ clock-names = "spi_clk";
+ atmel,fifo-size = <32>;
+
+ mtd_dataflash at 0 {
+ compatible = "atmel,at25f512b";
+ reg = <0>;
+ spi-max-frequency = <20000000>;
+ };
+ };
+};
--
1.8.2.2
^ permalink raw reply related [flat|nested] 18+ messages in thread
* [PATCH v2 2/2] mfd: flexcom: add a driver for Atmel Flexible Serial Communication Unit
2015-06-18 13:05 ` Cyrille Pitchen
(?)
@ 2015-06-18 13:05 ` Cyrille Pitchen
-1 siblings, 0 replies; 18+ messages in thread
From: Cyrille Pitchen @ 2015-06-18 13:05 UTC (permalink / raw)
To: nicolas.ferre, boris.brezillon, alexandre.belloni, sameo,
lee.jones
Cc: linux-arm-kernel, linux-kernel, robh+dt, pawel.moll, mark.rutland,
ijc+devicetree, galak, devicetree, Cyrille Pitchen
This driver supports the new Atmel Flexcom. The Flexcom is a wrapper which
integrates one SPI controller, one I2C controller and one USART. Only one
function can be enabled at a time. This driver selects the function once
for all, when the Flexcom is probed, according to the value of the new
"atmel,flexcom-mode" device tree property.
This driver has chosen to present the Flexcom to the system as a MFD so
the implementation is seamless for the existing Atmel SPI, I2C and USART
drivers.
Also the Flexcom embeds FIFOs: the latest patches of the SPI, I2C and
USART drivers take advantage of this new feature.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
---
drivers/mfd/Kconfig | 11 +++++
drivers/mfd/Makefile | 1 +
drivers/mfd/atmel-flexcom.c | 97 +++++++++++++++++++++++++++++++++++++++++++++
3 files changed, 109 insertions(+)
create mode 100644 drivers/mfd/atmel-flexcom.c
diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
index d5ad04d..9b33ad0 100644
--- a/drivers/mfd/Kconfig
+++ b/drivers/mfd/Kconfig
@@ -59,6 +59,17 @@ config MFD_AAT2870_CORE
additional drivers must be enabled in order to use the
functionality of the device.
+config MFD_ATMEL_FLEXCOM
+ tristate "Atmel Flexcom (Flexible Serial Communication Unit)"
+ select MFD_CORE
+ depends on OF
+ help
+ Select this to get support for Atmel Flexcom. This is a wrapper
+ which embeds a SPI controller, a I2C controller and a USART. Only
+ one function can be used at a time. The choice is done at boot time
+ by the probe function of this MFD driver according to a device tree
+ property.
+
config MFD_ATMEL_HLCDC
tristate "Atmel HLCDC (High-end LCD Controller)"
select MFD_CORE
diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile
index 0e5cfeb..c666bf5 100644
--- a/drivers/mfd/Makefile
+++ b/drivers/mfd/Makefile
@@ -160,6 +160,7 @@ obj-$(CONFIG_MFD_SPMI_PMIC) += qcom-spmi-pmic.o
obj-$(CONFIG_TPS65911_COMPARATOR) += tps65911-comparator.o
obj-$(CONFIG_MFD_TPS65090) += tps65090.o
obj-$(CONFIG_MFD_AAT2870_CORE) += aat2870-core.o
+obj-$(CONFIG_MFD_ATMEL_FLEXCOM) += atmel-flexcom.o
obj-$(CONFIG_MFD_ATMEL_HLCDC) += atmel-hlcdc.o
obj-$(CONFIG_MFD_INTEL_MSIC) += intel_msic.o
obj-$(CONFIG_MFD_PALMAS) += palmas.o
diff --git a/drivers/mfd/atmel-flexcom.c b/drivers/mfd/atmel-flexcom.c
new file mode 100644
index 0000000..fb348d9
--- /dev/null
+++ b/drivers/mfd/atmel-flexcom.c
@@ -0,0 +1,97 @@
+/*
+ * Driver for Atmel Flexcom
+ *
+ * Copyright (C) 2015 Atmel Corporation
+ *
+ * Author: Cyrille Pitchen <cyrille.pitchen@atmel.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ */
+
+#include <linux/module.h>
+#include <linux/types.h>
+#include <linux/kernel.h>
+#include <linux/platform_device.h>
+#include <linux/of.h>
+#include <linux/of_platform.h>
+#include <linux/err.h>
+#include <linux/io.h>
+#include <linux/clk.h>
+
+#define FX_MR 0x0
+#define FX_RHR 0x10
+#define FX_THR 0x20
+#define FX_VERSION 0xfc
+
+#define FX_MR_NO_COM 0
+#define FX_MR_USART 1
+#define FX_MR_SPI 2
+#define FX_MR_TWI 3
+
+
+static int atmel_flexcom_probe(struct platform_device *pdev)
+{
+ struct clk *clk;
+ struct resource *res;
+ unsigned char __iomem *map;
+ unsigned int version, mr;
+ const char *mode;
+ int err;
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ map = devm_ioremap_resource(&pdev->dev, res);
+ if (IS_ERR(map))
+ return PTR_ERR(map);
+
+ clk = devm_clk_get(&pdev->dev, NULL);
+ if (IS_ERR(clk))
+ return PTR_ERR(clk);
+
+ err = of_property_read_string(pdev->dev.of_node,
+ "atmel,flexcom-mode", &mode);
+ if (err)
+ return err;
+
+ if (!strcmp(mode, "usart"))
+ mr = FX_MR_USART;
+ else if (!strcmp(mode, "spi"))
+ mr = FX_MR_SPI;
+ else if (!strcmp(mode, "twi") || !strcmp(mode, "i2c"))
+ mr = FX_MR_TWI;
+ else
+ return -EINVAL;
+
+ clk_prepare_enable(clk);
+ version = readl(map + FX_VERSION);
+ writel(mr, map + FX_MR);
+ clk_disable_unprepare(clk);
+
+ dev_info(&pdev->dev, "hw version: %#x, mode: %s\n", version, mode);
+
+ return of_platform_populate(pdev->dev.of_node, NULL, NULL, &pdev->dev);
+}
+
+static const struct of_device_id atmel_flexcom_of_match[] = {
+ { .compatible = "atmel,sama5d2-flexcom" },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, atmel_flexcom_of_match);
+
+static struct platform_driver atmel_flexcom_driver = {
+ .driver = {
+ .name = "atmel_flexcom",
+ .of_match_table = atmel_flexcom_of_match,
+ },
+ .probe = atmel_flexcom_probe,
+};
+
+module_platform_driver(atmel_flexcom_driver);
+
+MODULE_AUTHOR("Cyrille Pitchen <cyrille.pitchen@atmel.com>");
+MODULE_DESCRIPTION("Atmel Flexcom MFD driver");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:atmel_flexcom");
--
1.8.2.2
^ permalink raw reply related [flat|nested] 18+ messages in thread
* [PATCH v2 2/2] mfd: flexcom: add a driver for Atmel Flexible Serial Communication Unit
@ 2015-06-18 13:05 ` Cyrille Pitchen
0 siblings, 0 replies; 18+ messages in thread
From: Cyrille Pitchen @ 2015-06-18 13:05 UTC (permalink / raw)
To: nicolas.ferre, boris.brezillon, alexandre.belloni, sameo,
lee.jones
Cc: linux-arm-kernel, linux-kernel, robh+dt, pawel.moll, mark.rutland,
ijc+devicetree, galak, devicetree, Cyrille Pitchen
This driver supports the new Atmel Flexcom. The Flexcom is a wrapper which
integrates one SPI controller, one I2C controller and one USART. Only one
function can be enabled at a time. This driver selects the function once
for all, when the Flexcom is probed, according to the value of the new
"atmel,flexcom-mode" device tree property.
This driver has chosen to present the Flexcom to the system as a MFD so
the implementation is seamless for the existing Atmel SPI, I2C and USART
drivers.
Also the Flexcom embeds FIFOs: the latest patches of the SPI, I2C and
USART drivers take advantage of this new feature.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
---
drivers/mfd/Kconfig | 11 +++++
drivers/mfd/Makefile | 1 +
drivers/mfd/atmel-flexcom.c | 97 +++++++++++++++++++++++++++++++++++++++++++++
3 files changed, 109 insertions(+)
create mode 100644 drivers/mfd/atmel-flexcom.c
diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
index d5ad04d..9b33ad0 100644
--- a/drivers/mfd/Kconfig
+++ b/drivers/mfd/Kconfig
@@ -59,6 +59,17 @@ config MFD_AAT2870_CORE
additional drivers must be enabled in order to use the
functionality of the device.
+config MFD_ATMEL_FLEXCOM
+ tristate "Atmel Flexcom (Flexible Serial Communication Unit)"
+ select MFD_CORE
+ depends on OF
+ help
+ Select this to get support for Atmel Flexcom. This is a wrapper
+ which embeds a SPI controller, a I2C controller and a USART. Only
+ one function can be used at a time. The choice is done at boot time
+ by the probe function of this MFD driver according to a device tree
+ property.
+
config MFD_ATMEL_HLCDC
tristate "Atmel HLCDC (High-end LCD Controller)"
select MFD_CORE
diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile
index 0e5cfeb..c666bf5 100644
--- a/drivers/mfd/Makefile
+++ b/drivers/mfd/Makefile
@@ -160,6 +160,7 @@ obj-$(CONFIG_MFD_SPMI_PMIC) += qcom-spmi-pmic.o
obj-$(CONFIG_TPS65911_COMPARATOR) += tps65911-comparator.o
obj-$(CONFIG_MFD_TPS65090) += tps65090.o
obj-$(CONFIG_MFD_AAT2870_CORE) += aat2870-core.o
+obj-$(CONFIG_MFD_ATMEL_FLEXCOM) += atmel-flexcom.o
obj-$(CONFIG_MFD_ATMEL_HLCDC) += atmel-hlcdc.o
obj-$(CONFIG_MFD_INTEL_MSIC) += intel_msic.o
obj-$(CONFIG_MFD_PALMAS) += palmas.o
diff --git a/drivers/mfd/atmel-flexcom.c b/drivers/mfd/atmel-flexcom.c
new file mode 100644
index 0000000..fb348d9
--- /dev/null
+++ b/drivers/mfd/atmel-flexcom.c
@@ -0,0 +1,97 @@
+/*
+ * Driver for Atmel Flexcom
+ *
+ * Copyright (C) 2015 Atmel Corporation
+ *
+ * Author: Cyrille Pitchen <cyrille.pitchen@atmel.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ */
+
+#include <linux/module.h>
+#include <linux/types.h>
+#include <linux/kernel.h>
+#include <linux/platform_device.h>
+#include <linux/of.h>
+#include <linux/of_platform.h>
+#include <linux/err.h>
+#include <linux/io.h>
+#include <linux/clk.h>
+
+#define FX_MR 0x0
+#define FX_RHR 0x10
+#define FX_THR 0x20
+#define FX_VERSION 0xfc
+
+#define FX_MR_NO_COM 0
+#define FX_MR_USART 1
+#define FX_MR_SPI 2
+#define FX_MR_TWI 3
+
+
+static int atmel_flexcom_probe(struct platform_device *pdev)
+{
+ struct clk *clk;
+ struct resource *res;
+ unsigned char __iomem *map;
+ unsigned int version, mr;
+ const char *mode;
+ int err;
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ map = devm_ioremap_resource(&pdev->dev, res);
+ if (IS_ERR(map))
+ return PTR_ERR(map);
+
+ clk = devm_clk_get(&pdev->dev, NULL);
+ if (IS_ERR(clk))
+ return PTR_ERR(clk);
+
+ err = of_property_read_string(pdev->dev.of_node,
+ "atmel,flexcom-mode", &mode);
+ if (err)
+ return err;
+
+ if (!strcmp(mode, "usart"))
+ mr = FX_MR_USART;
+ else if (!strcmp(mode, "spi"))
+ mr = FX_MR_SPI;
+ else if (!strcmp(mode, "twi") || !strcmp(mode, "i2c"))
+ mr = FX_MR_TWI;
+ else
+ return -EINVAL;
+
+ clk_prepare_enable(clk);
+ version = readl(map + FX_VERSION);
+ writel(mr, map + FX_MR);
+ clk_disable_unprepare(clk);
+
+ dev_info(&pdev->dev, "hw version: %#x, mode: %s\n", version, mode);
+
+ return of_platform_populate(pdev->dev.of_node, NULL, NULL, &pdev->dev);
+}
+
+static const struct of_device_id atmel_flexcom_of_match[] = {
+ { .compatible = "atmel,sama5d2-flexcom" },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, atmel_flexcom_of_match);
+
+static struct platform_driver atmel_flexcom_driver = {
+ .driver = {
+ .name = "atmel_flexcom",
+ .of_match_table = atmel_flexcom_of_match,
+ },
+ .probe = atmel_flexcom_probe,
+};
+
+module_platform_driver(atmel_flexcom_driver);
+
+MODULE_AUTHOR("Cyrille Pitchen <cyrille.pitchen@atmel.com>");
+MODULE_DESCRIPTION("Atmel Flexcom MFD driver");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:atmel_flexcom");
--
1.8.2.2
^ permalink raw reply related [flat|nested] 18+ messages in thread
* [PATCH v2 2/2] mfd: flexcom: add a driver for Atmel Flexible Serial Communication Unit
@ 2015-06-18 13:05 ` Cyrille Pitchen
0 siblings, 0 replies; 18+ messages in thread
From: Cyrille Pitchen @ 2015-06-18 13:05 UTC (permalink / raw)
To: linux-arm-kernel
This driver supports the new Atmel Flexcom. The Flexcom is a wrapper which
integrates one SPI controller, one I2C controller and one USART. Only one
function can be enabled at a time. This driver selects the function once
for all, when the Flexcom is probed, according to the value of the new
"atmel,flexcom-mode" device tree property.
This driver has chosen to present the Flexcom to the system as a MFD so
the implementation is seamless for the existing Atmel SPI, I2C and USART
drivers.
Also the Flexcom embeds FIFOs: the latest patches of the SPI, I2C and
USART drivers take advantage of this new feature.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
---
drivers/mfd/Kconfig | 11 +++++
drivers/mfd/Makefile | 1 +
drivers/mfd/atmel-flexcom.c | 97 +++++++++++++++++++++++++++++++++++++++++++++
3 files changed, 109 insertions(+)
create mode 100644 drivers/mfd/atmel-flexcom.c
diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
index d5ad04d..9b33ad0 100644
--- a/drivers/mfd/Kconfig
+++ b/drivers/mfd/Kconfig
@@ -59,6 +59,17 @@ config MFD_AAT2870_CORE
additional drivers must be enabled in order to use the
functionality of the device.
+config MFD_ATMEL_FLEXCOM
+ tristate "Atmel Flexcom (Flexible Serial Communication Unit)"
+ select MFD_CORE
+ depends on OF
+ help
+ Select this to get support for Atmel Flexcom. This is a wrapper
+ which embeds a SPI controller, a I2C controller and a USART. Only
+ one function can be used at a time. The choice is done at boot time
+ by the probe function of this MFD driver according to a device tree
+ property.
+
config MFD_ATMEL_HLCDC
tristate "Atmel HLCDC (High-end LCD Controller)"
select MFD_CORE
diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile
index 0e5cfeb..c666bf5 100644
--- a/drivers/mfd/Makefile
+++ b/drivers/mfd/Makefile
@@ -160,6 +160,7 @@ obj-$(CONFIG_MFD_SPMI_PMIC) += qcom-spmi-pmic.o
obj-$(CONFIG_TPS65911_COMPARATOR) += tps65911-comparator.o
obj-$(CONFIG_MFD_TPS65090) += tps65090.o
obj-$(CONFIG_MFD_AAT2870_CORE) += aat2870-core.o
+obj-$(CONFIG_MFD_ATMEL_FLEXCOM) += atmel-flexcom.o
obj-$(CONFIG_MFD_ATMEL_HLCDC) += atmel-hlcdc.o
obj-$(CONFIG_MFD_INTEL_MSIC) += intel_msic.o
obj-$(CONFIG_MFD_PALMAS) += palmas.o
diff --git a/drivers/mfd/atmel-flexcom.c b/drivers/mfd/atmel-flexcom.c
new file mode 100644
index 0000000..fb348d9
--- /dev/null
+++ b/drivers/mfd/atmel-flexcom.c
@@ -0,0 +1,97 @@
+/*
+ * Driver for Atmel Flexcom
+ *
+ * Copyright (C) 2015 Atmel Corporation
+ *
+ * Author: Cyrille Pitchen <cyrille.pitchen@atmel.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ */
+
+#include <linux/module.h>
+#include <linux/types.h>
+#include <linux/kernel.h>
+#include <linux/platform_device.h>
+#include <linux/of.h>
+#include <linux/of_platform.h>
+#include <linux/err.h>
+#include <linux/io.h>
+#include <linux/clk.h>
+
+#define FX_MR 0x0
+#define FX_RHR 0x10
+#define FX_THR 0x20
+#define FX_VERSION 0xfc
+
+#define FX_MR_NO_COM 0
+#define FX_MR_USART 1
+#define FX_MR_SPI 2
+#define FX_MR_TWI 3
+
+
+static int atmel_flexcom_probe(struct platform_device *pdev)
+{
+ struct clk *clk;
+ struct resource *res;
+ unsigned char __iomem *map;
+ unsigned int version, mr;
+ const char *mode;
+ int err;
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ map = devm_ioremap_resource(&pdev->dev, res);
+ if (IS_ERR(map))
+ return PTR_ERR(map);
+
+ clk = devm_clk_get(&pdev->dev, NULL);
+ if (IS_ERR(clk))
+ return PTR_ERR(clk);
+
+ err = of_property_read_string(pdev->dev.of_node,
+ "atmel,flexcom-mode", &mode);
+ if (err)
+ return err;
+
+ if (!strcmp(mode, "usart"))
+ mr = FX_MR_USART;
+ else if (!strcmp(mode, "spi"))
+ mr = FX_MR_SPI;
+ else if (!strcmp(mode, "twi") || !strcmp(mode, "i2c"))
+ mr = FX_MR_TWI;
+ else
+ return -EINVAL;
+
+ clk_prepare_enable(clk);
+ version = readl(map + FX_VERSION);
+ writel(mr, map + FX_MR);
+ clk_disable_unprepare(clk);
+
+ dev_info(&pdev->dev, "hw version: %#x, mode: %s\n", version, mode);
+
+ return of_platform_populate(pdev->dev.of_node, NULL, NULL, &pdev->dev);
+}
+
+static const struct of_device_id atmel_flexcom_of_match[] = {
+ { .compatible = "atmel,sama5d2-flexcom" },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, atmel_flexcom_of_match);
+
+static struct platform_driver atmel_flexcom_driver = {
+ .driver = {
+ .name = "atmel_flexcom",
+ .of_match_table = atmel_flexcom_of_match,
+ },
+ .probe = atmel_flexcom_probe,
+};
+
+module_platform_driver(atmel_flexcom_driver);
+
+MODULE_AUTHOR("Cyrille Pitchen <cyrille.pitchen@atmel.com>");
+MODULE_DESCRIPTION("Atmel Flexcom MFD driver");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:atmel_flexcom");
--
1.8.2.2
^ permalink raw reply related [flat|nested] 18+ messages in thread
* Re: [PATCH v2 0/2] mfd: flexcom: add a driver for Flexcom
2015-06-18 13:05 ` Cyrille Pitchen
(?)
@ 2015-06-18 13:09 ` Boris Brezillon
-1 siblings, 0 replies; 18+ messages in thread
From: Boris Brezillon @ 2015-06-18 13:09 UTC (permalink / raw)
To: Cyrille Pitchen
Cc: nicolas.ferre, alexandre.belloni, sameo, lee.jones,
linux-arm-kernel, linux-kernel, robh+dt, pawel.moll, mark.rutland,
ijc+devicetree, galak, devicetree
On Thu, 18 Jun 2015 15:05:08 +0200
Cyrille Pitchen <cyrille.pitchen@atmel.com> wrote:
> ChangeLog
>
> v2:
> - enhance the documentation of DT bindings and change the way the "ranges"
> property is used.
> - replace __raw_readl() and __raw_writel() by readl() and writel().
> - change the module license to "GPL" for v2 or later
> - print the selected flexcom mode after the hardware version
>
> v1:
> This series of patches a support to the Atmel Flexcom, a wrapper which
> integrates an USART, a SPI controller and a TWI controller. Only one
> peripheral can be used at a time. The active function is selected though
> the Flexcom Mode Register.
For the whole series,
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
>
> Cyrille Pitchen (2):
> mfd: devicetree: add bindings for Atmel Flexcom
> mfd: flexcom: add a driver for Atmel Flexible Serial Communication
> Unit
>
> .../devicetree/bindings/mfd/atmel-flexcom.txt | 58 +++++++++++++
> drivers/mfd/Kconfig | 11 +++
> drivers/mfd/Makefile | 1 +
> drivers/mfd/atmel-flexcom.c | 97 ++++++++++++++++++++++
> 4 files changed, 167 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/mfd/atmel-flexcom.txt
> create mode 100644 drivers/mfd/atmel-flexcom.c
>
--
Boris Brezillon, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: [PATCH v2 0/2] mfd: flexcom: add a driver for Flexcom
@ 2015-06-18 13:09 ` Boris Brezillon
0 siblings, 0 replies; 18+ messages in thread
From: Boris Brezillon @ 2015-06-18 13:09 UTC (permalink / raw)
To: Cyrille Pitchen
Cc: nicolas.ferre, alexandre.belloni, sameo, lee.jones,
linux-arm-kernel, linux-kernel, robh+dt, pawel.moll, mark.rutland,
ijc+devicetree, galak, devicetree
On Thu, 18 Jun 2015 15:05:08 +0200
Cyrille Pitchen <cyrille.pitchen@atmel.com> wrote:
> ChangeLog
>
> v2:
> - enhance the documentation of DT bindings and change the way the "ranges"
> property is used.
> - replace __raw_readl() and __raw_writel() by readl() and writel().
> - change the module license to "GPL" for v2 or later
> - print the selected flexcom mode after the hardware version
>
> v1:
> This series of patches a support to the Atmel Flexcom, a wrapper which
> integrates an USART, a SPI controller and a TWI controller. Only one
> peripheral can be used at a time. The active function is selected though
> the Flexcom Mode Register.
For the whole series,
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
>
> Cyrille Pitchen (2):
> mfd: devicetree: add bindings for Atmel Flexcom
> mfd: flexcom: add a driver for Atmel Flexible Serial Communication
> Unit
>
> .../devicetree/bindings/mfd/atmel-flexcom.txt | 58 +++++++++++++
> drivers/mfd/Kconfig | 11 +++
> drivers/mfd/Makefile | 1 +
> drivers/mfd/atmel-flexcom.c | 97 ++++++++++++++++++++++
> 4 files changed, 167 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/mfd/atmel-flexcom.txt
> create mode 100644 drivers/mfd/atmel-flexcom.c
>
--
Boris Brezillon, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
^ permalink raw reply [flat|nested] 18+ messages in thread
* [PATCH v2 0/2] mfd: flexcom: add a driver for Flexcom
@ 2015-06-18 13:09 ` Boris Brezillon
0 siblings, 0 replies; 18+ messages in thread
From: Boris Brezillon @ 2015-06-18 13:09 UTC (permalink / raw)
To: linux-arm-kernel
On Thu, 18 Jun 2015 15:05:08 +0200
Cyrille Pitchen <cyrille.pitchen@atmel.com> wrote:
> ChangeLog
>
> v2:
> - enhance the documentation of DT bindings and change the way the "ranges"
> property is used.
> - replace __raw_readl() and __raw_writel() by readl() and writel().
> - change the module license to "GPL" for v2 or later
> - print the selected flexcom mode after the hardware version
>
> v1:
> This series of patches a support to the Atmel Flexcom, a wrapper which
> integrates an USART, a SPI controller and a TWI controller. Only one
> peripheral can be used at a time. The active function is selected though
> the Flexcom Mode Register.
For the whole series,
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
>
> Cyrille Pitchen (2):
> mfd: devicetree: add bindings for Atmel Flexcom
> mfd: flexcom: add a driver for Atmel Flexible Serial Communication
> Unit
>
> .../devicetree/bindings/mfd/atmel-flexcom.txt | 58 +++++++++++++
> drivers/mfd/Kconfig | 11 +++
> drivers/mfd/Makefile | 1 +
> drivers/mfd/atmel-flexcom.c | 97 ++++++++++++++++++++++
> 4 files changed, 167 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/mfd/atmel-flexcom.txt
> create mode 100644 drivers/mfd/atmel-flexcom.c
>
--
Boris Brezillon, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: [PATCH v2 0/2] mfd: flexcom: add a driver for Flexcom
@ 2015-06-18 14:52 ` Alexandre Belloni
0 siblings, 0 replies; 18+ messages in thread
From: Alexandre Belloni @ 2015-06-18 14:52 UTC (permalink / raw)
To: Cyrille Pitchen
Cc: nicolas.ferre, boris.brezillon, sameo, lee.jones,
linux-arm-kernel, linux-kernel, robh+dt, pawel.moll, mark.rutland,
ijc+devicetree, galak, devicetree
On 18/06/2015 at 15:05:08 +0200, Cyrille Pitchen wrote :
> ChangeLog
>
> v2:
> - enhance the documentation of DT bindings and change the way the "ranges"
> property is used.
> - replace __raw_readl() and __raw_writel() by readl() and writel().
> - change the module license to "GPL" for v2 or later
> - print the selected flexcom mode after the hardware version
>
> v1:
> This series of patches a support to the Atmel Flexcom, a wrapper which
> integrates an USART, a SPI controller and a TWI controller. Only one
> peripheral can be used at a time. The active function is selected though
> the Flexcom Mode Register.
>
For the whole set:
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
--
Alexandre Belloni, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: [PATCH v2 0/2] mfd: flexcom: add a driver for Flexcom
@ 2015-06-18 14:52 ` Alexandre Belloni
0 siblings, 0 replies; 18+ messages in thread
From: Alexandre Belloni @ 2015-06-18 14:52 UTC (permalink / raw)
To: Cyrille Pitchen
Cc: nicolas.ferre-AIFe0yeh4nAAvxtiuMwx3w,
boris.brezillon-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8,
sameo-VuQAYsv1563Yd54FQh9/CA, lee.jones-QSEj5FYQhm4dnm+yROfE0A,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
robh+dt-DgEjT+Ai2ygdnm+yROfE0A, pawel.moll-5wv7dgnIgG8,
mark.rutland-5wv7dgnIgG8, ijc+devicetree-KcIKpvwj1kUDXYZnReoRVg,
galak-sgV2jX0FEOL9JmXXK+q4OQ, devicetree-u79uwXL29TY76Z2rM5mHXA
On 18/06/2015 at 15:05:08 +0200, Cyrille Pitchen wrote :
> ChangeLog
>
> v2:
> - enhance the documentation of DT bindings and change the way the "ranges"
> property is used.
> - replace __raw_readl() and __raw_writel() by readl() and writel().
> - change the module license to "GPL" for v2 or later
> - print the selected flexcom mode after the hardware version
>
> v1:
> This series of patches a support to the Atmel Flexcom, a wrapper which
> integrates an USART, a SPI controller and a TWI controller. Only one
> peripheral can be used at a time. The active function is selected though
> the Flexcom Mode Register.
>
For the whole set:
Acked-by: Alexandre Belloni <alexandre.belloni-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
--
Alexandre Belloni, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 18+ messages in thread
* [PATCH v2 0/2] mfd: flexcom: add a driver for Flexcom
@ 2015-06-18 14:52 ` Alexandre Belloni
0 siblings, 0 replies; 18+ messages in thread
From: Alexandre Belloni @ 2015-06-18 14:52 UTC (permalink / raw)
To: linux-arm-kernel
On 18/06/2015 at 15:05:08 +0200, Cyrille Pitchen wrote :
> ChangeLog
>
> v2:
> - enhance the documentation of DT bindings and change the way the "ranges"
> property is used.
> - replace __raw_readl() and __raw_writel() by readl() and writel().
> - change the module license to "GPL" for v2 or later
> - print the selected flexcom mode after the hardware version
>
> v1:
> This series of patches a support to the Atmel Flexcom, a wrapper which
> integrates an USART, a SPI controller and a TWI controller. Only one
> peripheral can be used at a time. The active function is selected though
> the Flexcom Mode Register.
>
For the whole set:
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
--
Alexandre Belloni, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: [PATCH v2 2/2] mfd: flexcom: add a driver for Atmel Flexible Serial Communication Unit
@ 2015-06-19 7:34 ` Paul Bolle
0 siblings, 0 replies; 18+ messages in thread
From: Paul Bolle @ 2015-06-19 7:34 UTC (permalink / raw)
To: Cyrille Pitchen
Cc: nicolas.ferre, boris.brezillon, alexandre.belloni, sameo,
lee.jones, linux-arm-kernel, linux-kernel, robh+dt, pawel.moll,
mark.rutland, ijc+devicetree, galak, devicetree
On Thu, 2015-06-18 at 15:05 +0200, Cyrille Pitchen wrote:
> --- /dev/null
> +++ b/drivers/mfd/atmel-flexcom.c
> +MODULE_ALIAS("platform:atmel_flexcom");
(The day before yesterday and yesterday I had a, well, lively
conversation regarding this macro. The interesting bits start at
https://lkml.org/lkml/2015/6/17/383 . Let's see how things go here.)
As I understand it, this alias is only useful if there's a corresponding
struct platform_device, somewhere. Ie, this alias implies a
platform_device that will fire of a "MODALIAS=platform:atmel_flexcom"
uevent when it's created. That would be a platform_device using a
"atmel_flexcom" name.
If that's correct, then I think this MODULE_ALIAS macro isn't needed
here, as I couldn't find a platform_device using that name. (But perhaps
a patch that adds it is pending, somewhere.)
Thanks,
Paul Bolle
^ permalink raw reply [flat|nested] 18+ messages in thread
* Re: [PATCH v2 2/2] mfd: flexcom: add a driver for Atmel Flexible Serial Communication Unit
@ 2015-06-19 7:34 ` Paul Bolle
0 siblings, 0 replies; 18+ messages in thread
From: Paul Bolle @ 2015-06-19 7:34 UTC (permalink / raw)
To: Cyrille Pitchen
Cc: nicolas.ferre-AIFe0yeh4nAAvxtiuMwx3w,
boris.brezillon-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8,
alexandre.belloni-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8,
sameo-VuQAYsv1563Yd54FQh9/CA, lee.jones-QSEj5FYQhm4dnm+yROfE0A,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
robh+dt-DgEjT+Ai2ygdnm+yROfE0A, pawel.moll-5wv7dgnIgG8,
mark.rutland-5wv7dgnIgG8, ijc+devicetree-KcIKpvwj1kUDXYZnReoRVg,
galak-sgV2jX0FEOL9JmXXK+q4OQ, devicetree-u79uwXL29TY76Z2rM5mHXA
On Thu, 2015-06-18 at 15:05 +0200, Cyrille Pitchen wrote:
> --- /dev/null
> +++ b/drivers/mfd/atmel-flexcom.c
> +MODULE_ALIAS("platform:atmel_flexcom");
(The day before yesterday and yesterday I had a, well, lively
conversation regarding this macro. The interesting bits start at
https://lkml.org/lkml/2015/6/17/383 . Let's see how things go here.)
As I understand it, this alias is only useful if there's a corresponding
struct platform_device, somewhere. Ie, this alias implies a
platform_device that will fire of a "MODALIAS=platform:atmel_flexcom"
uevent when it's created. That would be a platform_device using a
"atmel_flexcom" name.
If that's correct, then I think this MODULE_ALIAS macro isn't needed
here, as I couldn't find a platform_device using that name. (But perhaps
a patch that adds it is pending, somewhere.)
Thanks,
Paul Bolle
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 18+ messages in thread
* [PATCH v2 2/2] mfd: flexcom: add a driver for Atmel Flexible Serial Communication Unit
@ 2015-06-19 7:34 ` Paul Bolle
0 siblings, 0 replies; 18+ messages in thread
From: Paul Bolle @ 2015-06-19 7:34 UTC (permalink / raw)
To: linux-arm-kernel
On Thu, 2015-06-18 at 15:05 +0200, Cyrille Pitchen wrote:
> --- /dev/null
> +++ b/drivers/mfd/atmel-flexcom.c
> +MODULE_ALIAS("platform:atmel_flexcom");
(The day before yesterday and yesterday I had a, well, lively
conversation regarding this macro. The interesting bits start at
https://lkml.org/lkml/2015/6/17/383 . Let's see how things go here.)
As I understand it, this alias is only useful if there's a corresponding
struct platform_device, somewhere. Ie, this alias implies a
platform_device that will fire of a "MODALIAS=platform:atmel_flexcom"
uevent when it's created. That would be a platform_device using a
"atmel_flexcom" name.
If that's correct, then I think this MODULE_ALIAS macro isn't needed
here, as I couldn't find a platform_device using that name. (But perhaps
a patch that adds it is pending, somewhere.)
Thanks,
Paul Bolle
^ permalink raw reply [flat|nested] 18+ messages in thread
end of thread, other threads:[~2015-06-19 7:34 UTC | newest]
Thread overview: 18+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2015-06-18 13:05 [PATCH v2 0/2] mfd: flexcom: add a driver for Flexcom Cyrille Pitchen
2015-06-18 13:05 ` Cyrille Pitchen
2015-06-18 13:05 ` Cyrille Pitchen
2015-06-18 13:05 ` [PATCH v2 1/2] mfd: devicetree: add bindings for Atmel Flexcom Cyrille Pitchen
2015-06-18 13:05 ` Cyrille Pitchen
2015-06-18 13:05 ` Cyrille Pitchen
2015-06-18 13:05 ` [PATCH v2 2/2] mfd: flexcom: add a driver for Atmel Flexible Serial Communication Unit Cyrille Pitchen
2015-06-18 13:05 ` Cyrille Pitchen
2015-06-18 13:05 ` Cyrille Pitchen
2015-06-19 7:34 ` Paul Bolle
2015-06-19 7:34 ` Paul Bolle
2015-06-19 7:34 ` Paul Bolle
2015-06-18 13:09 ` [PATCH v2 0/2] mfd: flexcom: add a driver for Flexcom Boris Brezillon
2015-06-18 13:09 ` Boris Brezillon
2015-06-18 13:09 ` Boris Brezillon
2015-06-18 14:52 ` Alexandre Belloni
2015-06-18 14:52 ` Alexandre Belloni
2015-06-18 14:52 ` Alexandre Belloni
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.