From: Lee Jones <lee.jones@linaro.org>
To: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Cc: cw00.choi@samsung.com, myungjoo.ham@samsung.com,
linux-kernel@vger.kernel.org,
patches@opensource.wolfsonmicro.com, devicetree@vger.kernel.org
Subject: Re: [PATCH v3 6/7] mfd: arizona: Update DT doc for new mic detection bindings
Date: Wed, 24 Jun 2015 15:15:34 +0100 [thread overview]
Message-ID: <20150624141534.GN15013@x1> (raw)
In-Reply-To: <1434709467-28147-7-git-send-email-ckeepax@opensource.wolfsonmicro.com>
This requires a DT Ack.
[... which would be pretty difficult, as you didn't Cc them]
> Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
> ---
> Documentation/devicetree/bindings/mfd/arizona.txt | 16 ++++++++++++++++
> 1 files changed, 16 insertions(+), 0 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/mfd/arizona.txt b/Documentation/devicetree/bindings/mfd/arizona.txt
> index 32a71b7..8d92c92 100644
> --- a/Documentation/devicetree/bindings/mfd/arizona.txt
> +++ b/Documentation/devicetree/bindings/mfd/arizona.txt
> @@ -68,6 +68,22 @@ Optional properties:
> If this node is not mentioned or if the value is unknown, then
> headphone detection mode is set to HPDETL.
>
> + - wlf,micd-detect-debounce : Additional software microphone detection
> + debounce specified in milliseconds.
> + - wlf,micd-pol-gpio : GPIO specifier for the GPIO controlling the headset
> + polarity if one exists.
> + - wlf,micd-bias-start-time : Time allowed for MICBIAS to startup prior to
> + performing microphone detection, specified as per the ARIZONA_MICD_TIME_XXX
> + defines.
> + - wlf,micd-rate : Delay between successive microphone detection measurements,
> + specified as per the ARIZONA_MICD_TIME_XXX defines.
> + - wlf,micd-dbtime : Microphone detection hardware debounces specified as the
> + number of measurements to take, valid values being 2 and 4.
> + - wlf,micd-timeout : Timeout for microphone detection, specified in
> + milliseconds.
> + - wlf,micd-force-micbias : Force MICBIAS continuously on during microphone
> + detection.
> +
> - DCVDD-supply, MICVDD-supply : Power supplies, only need to be specified if
> they are being externally supplied. As covered in
> Documentation/devicetree/bindings/regulator/regulator.txt
--
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
next prev parent reply other threads:[~2015-06-24 14:15 UTC|newest]
Thread overview: 18+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-06-19 10:24 [PATCH v3 0/7] Add basic microphone detection bindings Charles Keepax
2015-06-19 10:24 ` [PATCH v3 1/7] extcon: arizona: Factor out initial GPIO state Charles Keepax
2015-06-19 12:29 ` Chanwoo Choi
2015-06-19 12:54 ` Charles Keepax
2015-06-19 10:24 ` [PATCH v3 2/7] extcon: arizona: Update to use the new device properties API Charles Keepax
2015-06-19 10:24 ` [PATCH v3 3/7] extcon: arizona: Add basic microphone detection DT/ACPI bindings Charles Keepax
2015-06-19 10:24 ` [PATCH v3 4/7] extcon: arizona: Convert to gpiod Charles Keepax
2015-06-19 10:24 ` [PATCH v3 5/7] extcon: arizona: Ensure variables are set for headphone detection Charles Keepax
2015-06-19 10:24 ` [PATCH v3 6/7] mfd: arizona: Update DT doc for new mic detection bindings Charles Keepax
2015-06-24 14:15 ` Lee Jones [this message]
2015-06-24 15:41 ` Charles Keepax
2015-06-25 8:53 ` Lee Jones
2015-06-25 8:53 ` Lee Jones
2015-06-19 10:24 ` [PATCH v3 7/7] mfd: arizona: Update several pdata members to unsigned Charles Keepax
2015-06-24 14:16 ` Lee Jones
2015-06-19 10:46 ` [PATCH v3 0/7] Add basic microphone detection bindings Charles Keepax
-- strict thread matches above, loose matches on Subject: below --
2015-06-19 10:33 Charles Keepax
2015-06-19 10:33 ` [PATCH v3 6/7] mfd: arizona: Update DT doc for new mic " Charles Keepax
2015-06-19 10:33 ` Charles Keepax
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20150624141534.GN15013@x1 \
--to=lee.jones@linaro.org \
--cc=ckeepax@opensource.wolfsonmicro.com \
--cc=cw00.choi@samsung.com \
--cc=devicetree@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=myungjoo.ham@samsung.com \
--cc=patches@opensource.wolfsonmicro.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.